Open Short
Pinpoint open circuits.
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
Open-Short-Load RF calibration kits
-
Open-Short-Load RF calibration kits from Fairview Microwave are available with Type N or 7/16 DIN connectors. Type N open-short-load RF calibration kits have male or female genders, 7/16 DIN open-short-load kits are male gender. Type N open-short-load (OSL) calibration kits for RF have a minimum frequency of 0 (DC) and a maximum frequency range between 4 GHz and 6 GHz. Type N open short load kits for calibration have a maximum power handling of between 1 Watt and 2 Watts.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
Product
x1149 Boundary Scan Analyzer
N1125A
Boundary Scan Analyzer
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
Product
LAN Cable Tester
PA-01D
-
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
Circuit Breaker Tester
LAN & Breaker
-
Find opens, shorts and mis-wired cable installations with quick go/no-go tests, using an Amprobe LAN tester. Identifying circuit breakers is efficient when you use an Amprobe breaker tracer.
-
Product
LAN Cable Tester
21-8569-00
-
Open / Short / Misswiring test?BNC / RJ45 each pin connected display?No wire or termination?Isolation Resistances 50K ohms test
-
Product
External Powered IEPE Signal Conditioner
ADAM-3017
-
IEPE current support: 4, 6, 10 mAExternal powered operation eliminates line noiseLED indicator for sensor open, short and normal
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16 (female)
85038F
Mechanical Calibration Kit
The Keysight 85038F calibration kit contains only female calibration devices (open circuit, short circuit and termination) and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
-
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
Product
HDMI Cable Tester
MT-7062
-
Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.
-
Product
Line Loop Tester
8455
-
Simpson?s Model 8455 Line Loop tester detects line shorts, opens and multiple ringers, DC voltages and loop resistance. It can measure DC voltage up to 100 volts and loop resistance to 2 megohms. A front panel ?reverse polarity? switch allows changing polarity positions quicker and easier than manually switching test leads when making line checks.
-
Product
Audio Cable Testers
AudioJog Pro 5
-
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
Product
1 Mm Calibration Kit
85059B
Mechanical Calibration Kit
The Keysight 85059B is a 1.0 mm calibration kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. The opens, shorts and loads in this kit are optimized to provide accurate and traceable calibrations over the specified frequency range. The 85059B with 85059V 1 mm Verification kit are replacements for the 85059A 1 mm calibration/verification kit.
-
Product
Network Cable Tester
AVJoG Rack
-
*A single box solution for testing AV cables. *Easy to use with only one button operation. *Detects Open, Short and Crossed circuits. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *40+ preprogrammed cable types.
-
Product
Cable/Harness Tester
IST-380
-
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 9 GHz, Type-N(m), 50 Ohm
85514A
Mechanical Calibration Kit
Easily calibrate non-insertable devices with a type-N (m) 50 Ω open, short, load, and through in a compact unit
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (f)
CK058F
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
Product
Lan Cable Tester
-
Shanghai Beha Electronics Co., Ltd.
Is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc., By comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit., Provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
Product
Multimeter Network Tester
VA16
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
Product
Multi-Modular Cable Tester
MT-7051N
-
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
Product
4-In-1 OSLT Mechanical Calibration Kit, DC To 18 GHz, Type-N (f) 50 Ohm
85519A
Mechanical Calibration Kit
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
Product
Rack Mount Cable Tester
AudioJog Rack
-
There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections.
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
-
Product
Digital In-Circuit tester
MTS180/300
-
Analog in-circuit inspection and function inspection are realized on this inspection equipment. IC pin float function is standard equipment. The MTS180 is a press type jig, and the MTS300 is a vacuum type jig. In the board mounting process at the production site, electrical inspection is performed on the mounted board after component mounting, and non-defective or defective products are automatically judged. The main inspection contents are short / open inspection, analog inspection of resistors, capacitors, coils, diodes, etc., lead floating voltage measurement of QFP and BGA, Digital IC inspection, frequency measurement.
-
Product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
Signal Module
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
