References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Reference Oscillator
REF Series 1.5” x 1.5” x 0.6”
-
*Connectorized Package *Free Running *Low Phase Noise *Output Power to +12 dBm Available
-
Product
NI-9775 , ±10 V, Up to 20 MS/s/ch, 14-Bit, 4-Channel C Series Digitizer Module
784539-01
Digitizer
The NI-9775 provides referenced single-ended analog inputs with two timing modes for applications such as fault detection in electrical transmission lines or structural failure events. You can use the NI-9775 to measure finite samples up to 20 MS/s/ch to capture fault detections or to measure continuously at up to 4 MS/s. You also can use the built-in analog reference trigger to assist with high speed phenomena. Additionally, the NI-9775 supports waveform streaming at a lower sample rate.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 3U VPX
Model 52690
-
- Accepts RF Signals from 925 to 2175 MHz- Programmable LNA boosts LNB (low noise block) antenna signal levels with up to 60 dB gain- Programmable analog downconverter provides I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGA- 2 GB DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- Clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Industrial Internet Testbeds
-
Industrial Internet Consortium
A testbed is a controlled experimentation platform, conforming to an Industrial Internet Consortium reference architecture, where solutions can be deployed and tested in an environment that resembles real-world conditions. Testbeds explore untested technologies or existing technologies working together in an untested manner. Testbeds generate requirements and priorities for standards organizations, and culminate in new (potentially disruptive) products and services..
-
Product
2-Ch 500 MHz A/D w/ DDC & 2-Ch 800 MHz D/A w/ DUC, Virtex-6 FPGA - 3U VPX
Model 52651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- Up to 2 GB of DDR3 SDRAM or 16 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
UV Fluorescence Sulfur Dioxide Analyzer
Model T100
-
The Model T100 uses the proven UV fluorescence principle, coupled with a state of the art user interface to provide easy, accurate, and dependable measurements of low level SO2.Exceptional stability is achieved with the use of an optical shutter to compensate for PMT drift and a reference detector to correct for changes in UV lamp intensity. A hydrocarbon ‘kicker’ and advanced optical design combine to prevent inaccuracies due to interferents.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel using NumaView™ Software, or via RS232, Ethernet, or USB com ports, either locally or by remote connection using the included NumaView™ Remote PC Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.The Model T100 comes with NumaView ™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView ™ Software.
-
Product
PXIe System Sync Module, 2 Port
M9032A
System Sync Module
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
Product
Temperature Calibrators
-
Ensuring process temperature accuracy involves calibrating not only the system’s electronic temperature signals, but also the very temperature sensors that initiate those signals. Rugged Fluke handheld temperature calibrators source and measure RTDs and thermocouples, power transmitters, and store data. Fluke Calibration temperature sources cover temperatures from -45 °C to 1200 °C and include handheld, portable, and benchtop calibrators. Infrared thermometer calibrators and reference measurement thermometers ensure every necessary tool is available to you.
-
Product
Rectangular Horn Antennas
-
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
Product
QuartzXM Carrier Design Package
Model 4801
-
- Pin definitions and electrical specifications of all signals on the module- 3D models of the module- Thermal profiles of the module and components- Carrier reference design schematics- PCB stack-up recommendations- PCB design guidelines and routing rules- Operating systems and bootstrap guidelines- Additional electrical and mechanical engineering guidance
-
Product
Quality Control
Sandwich Box
-
Housed in a ruggedized box, the VQC Sandwich Box is a field-proven acquisition unit for testing all aspects of vibrator performance, providing real time display of accelerometer and reference signals during the sweep.
-
Product
nVision Reference Recorder
-
AMETEK Sensors, Test & Calibration
Accurate enough to replace a deadweight testerRugged enough to sit in 3 feet of waterPortable enough to complete calibrations anywhere
-
Product
Sensor Bodies
-
The armature - assembled sensor body - is the central component of an inline photometer. We have already designed more than 1000 different sensor bodies and more than 50 types are always on stock. All optek inline sensor bodies are made from high quality materials and are machined with extreme precision. The quality-tested manufacturing tolerances allow optical path lengths of up to 1000 mm, for which the accuracy of the incoming and outgoing light beam is ensured by testing a laser-based coaxiality tolerance test to the reference axis. To cover a wide spectrum of different process conditions, optek sensor bodies can be manufactured from various materials (also for aggressive chemicals or with NACE MR 0175) and adapted with regards to:
-
Product
Battery Rapid-Tester
Spectro CA-12
-
Spectro CA-12 battery rapid-tester estimates CCA and capacity. CCA (Cold Cranking Amp) refers to the ability to crank the engine; capacity, also known as reserve capacity, estimates electrical storage capability.
-
Product
PXIe-6614, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module
782353-01
Counter/Timer Module
PXIe, 5 V, 8-Channel, Precision Reference PXI Counter/Timer Module—The PXIe‑6614 is a high-precision counter/timer module that performs encoder position measurement, event counting, period measurement, pulse-width measurement, pulse generation, pulse-train generation, and frequency measurement. It features eight counter/timers, digital debouncing filters, and TTL/CMOS‑compatible digital I/O. The PXIe‑6614 offers industrially rugged features for a wide array of applications such as automotive/aerospace, industrial/motion control, and manufacturing test. Measurements are highly accurate and precise over longer periods of time because of the oven‑controlled crystal oscillator (OCXO) in the module.
-
Product
Power Line Isolators & Conditioners
-
A power line conditioner (also known as a line conditioner or power line conditioner) is a device intended to improve the quality of the power that is delivered to electrical load equipment. While there is no official definition of a power conditioner, the term most often refers to a device that acts in one or more ways to deliver a voltage of the proper level and characteristics to enable load equipment to function properly.In a nutshell, poor incoming electrical power converted to good output power.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
-
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
Product
Multimeter
CMM-10
-
*Autoranging/manual range selection.*DATA HOLD function, for holding measured values.*REL function, which allows you to make measurements relative to a stored reference value.*Continuity test with acoustic signalling (beeper).*AUTO-OFF function.*Display 3 7/8 digits (5000 max).
-
Product
Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um
AKSM13(A)-40
-
Model:AKSM13(A)-40 Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2umDetails&Spec: Please refer to KSM13(A)-40 Specification,It is combinated by2pcs KSM13(A)-40 (C,SR,SL) and 1pc KSM13(A)-40CZ(as vertical stage)
-
Product
FPGA Mezzanine Card
FMC176
-
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users.
-
Product
SMA Male to SMA Male Cable, 50 Ohm, 12.7 cm
763443-01
Coaxial Cable
The SMA-SMA Coaxial Cable, sometimes referred to as SMA100, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths.
-
Product
1-2 Independent, Dual Redundant 1553 Channels on Small Mezzanine
MEZ-E1553
Ethernet Interface
From our popular ENET product, the MEZ-E1553 is a small, rugged mezzanine product that can easily be integrated into your system design. Alta provides full reference schematics, design notes, STEP 3-D Files, and sample ESS test programs. Guaranteed 1553A/B/C compliant with AS4111 5.2 Protocol Test reports.
-
Product
SMB Female to BNC Female Cable, 50 Ohm, 61 cm
763389-01
Coaxial Cable
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. NI offers this 50 Ω cable in different lengths and quantities.
-
Product
1100-Channel GSM Channelizer wih Quad A/D - 3U VPX
Model 52663
-
- Complete GSM channelizer with analog IF interface- Four 180 MHz 16-bit A/Ds- Two banks of 375 DDCs for upper GSM band- Two banks of 175 DDCs for lower GSM band- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express Gen. 2 x4- 3U VPX form factor provides a compact, rugged platform- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Industrial CT Scanning Services
-
Computed tomography (CT) is also referred to as industrial x ray and industrial imaging. It is an x-ray methodology yielding 3-dimensional (3D) results by placing an object on a rotational stage between an x-ray tube and x ray detector, rotating the object 360 degrees and capturing images at specific intervals—such as every degree or every half degree.
-
Product
Adjustable High Frequency Reference Ballast
HCS-109A
-
HCS-109A Adjustable High Frequency Reference Ballast also called High Frequency Current Source. Comparing to IEC Test Method, HCS-109A is an Equivalent Test Method which is economic solution. HCS-109A equipped with Spectrophotometer & Integrating Sphere Test System. It can also measure the photo, color and electricity parameters for high frequency fluorescent lamp.Specifications: • Input voltage: 200V~240V, 50/60Hz • Input Power: 80 W max • Output Current: 130mA~400mA (Adjustable), accuracy: +/- 1% • Output Frequency: 25kHz< +/-2.0% (Adjustable), accuracy: +/- 0.3kHz • Output current total harmonic wave distortion: THD<2.5% (HF current wave)
-
Product
IP67 DC Blocking Splitter Combiner
PD5033
-
INSTOCK Wireless Components, Inc
PD5033 is an IP67 outdoor, weather resistant, DC blocking, three way, RF broadband, 50 ohm, power divider, power combiner furnished with N type coaxial connectors. The passive Wilkinson design passes RF and the 10 MHz reference signal through both ports while blocking DC current. This configuration is typically used in combining applications to prevent passing DC to the sum and adjacent ports. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5033 is a bidirectional device capable of 40 W max microwave input power levels in both power splitter and combiner apps. See 3 way power divider input rating tables for additional power handling info.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 0.5m
40-971B-200D-0.5m-MM
Cable Assembly
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
Product
GFS Primary Gravimetric Flow Standard
-
The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.
