Cable Fault Locators
Use time domain reflectometry to locate signal loss or a Murray loop bridge.
See Also: Cable TDR, Cable Sheath
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-194A-001
Fault Insertion Unit
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
Fault Insertion Unit
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
PXI Dual Bus 32-Chan 2A Fault Insert Switch
40-190B-202
Fault Insertion Unit
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-401
Fault Insertion Unit
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch, N/O Through Relays
40-190B-501
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally open through relays, so in the default state, there are no paths between inputs and outputs for any signal channel. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
40-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
-
Product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
Fault Insertion Unit
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
Fault Insertion Unit
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
Product
Cable Test Van
Titron
-
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
Product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
Fault Insertion Unit
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
Product
8-Pin Power D-Type Cable, Female to Unterminated, Cut Ends, 1m
40-972-408-1m-FU
Cable Assembly
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Cable Assy 9-Pin D-Type, M/M, 1m
40-970-009-1m-MM
Cable Assembly
A 9-Pin Cable Assembly suitable for general use and constructed from PFA insulated wire. The connector assembly can be sured to the product by screwlocks.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH w/ 4-40 Jackscrews
540005010105
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH w/ 4-40 Jackscrews
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 68-Pin Male SCSI
540118050203
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 68-Pin Male SCSI.
-
Product
68-Pin SCSI Micro-D M to 2x34 0.5m
40-971-068-0.5m-MF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
Product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 1m
40-971B-200-1m-MF
Cable Assembly
This male rear exit to ribbon cable 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 2m, 250 Port
A500RMR-500RMR-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 2 RJ45 Plugs
540224010140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 2 RJ45 Plugs
-
Product
Cable Assembly, 50-Pin D-Type, Male to Female, 0.5m HV
A050DM5-050DF5-HA050
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, 192-Pin Receiver, QuadraPaddle, 20", 160-Pin Female DIN, for Pickering
540069040140
Cable Assembly
Cable Assembly, Receiver, 20", QuadraPaddle,160-Pin Female DIN.Uses the 40-960-160-F kit for Pickering instruments.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 36", 68-Pin Male VHDCI
540120040240
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 36", 68-Pin Male VHDCI
-
Product
MCX Male to BNC Male Cable, 50 Ohm, 1 m
188375-01
Coaxial Cable
MCX Male to BNC Male Cable, 50 Ohm, 1 m
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Ferrules, 2m, Spring Latch
A068SFR-F-5B200
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly, 60", 68 Pin Female SCSI, 68 Pin Male SCSI
Cable Assembly
Cable Assembly, 60", 68 Pin Female SCSI, 68 Pin Male SCSI.
-
Product
24-Pin GPIB Male/Female to 24-Pin GPIB Male/Female, Stackable, Double-Shielded GPIB Cable
763061-003
GPIB Cable
The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. This cable features 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. Additionally, the 24M/F-24M/F X2 Cable is available in different lengths.
-
Product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Tinned Ends, 2 Amp, 2m, 250 Port
A500RMR-T-5C200
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
Product
Cable Assembly, 104-Pin D-Type, Male to Unterminated, Tinned Ends, 2A, 2m
A104HMR-T-0A200
Cable Assembly
This 2m long male to untermiated 104-Pin D-type Cable Assembly is suited for direct connection to various products using the 104-Pin connector. It is constructed from high-flexibilty, high-specification fully screened cable and is unterminated with tinned ends.
