Product

Phase Noise Measurement Solution, 50 kHz to 110 GHz

E5505A

-

Keysight Technologies

E5505A - Keysight Technologies

The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.

Product

Impedance Standards and Calibrators

-

MEATEST, s.r.o.

MEATEST, s.r.o.

Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.

Product

Standard Voltage 37 Pin D-Type Cables - Connector to Unterminated for Pickering

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.

Product

Portable Single Phase Power Factor Meter

-

Supreme Instrument Laboratories

Supreme Instrument Laboratories

Portable Electro-dynamometer type single phase single element Power Factor Meter laboratory type for horizontal use, housed in laminated wooden cabinet size 235 mm length x 200 mm width x 180 mm height, with detachable lid, black bakelite panel fitted with anti-parallax mirror scale, knife edge pointer, rubber footings, carrying handles, locking arrangements. The power Factor Meters are fitted with an iron shielded Electro-dynamometer type cross coil system.

Product

Single Phase Energy Meter Test Bench Type KP-S1000-A

-

Bofa Instrument & Equipment Co., Ltd

Bofa Instrument & Equipment Co., Ltd

Single phase test bench, type KP-S1000-A, is a new generation, high precision energy meter calibration equipment. It can test mechanical energy meter and electronic energy meter, in spite of open or closed test link (I-P link). It is an ideal testing equipment for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.

Product

3 Phase Power Monitors

-

Outram Research Ltd (ORL)

Outram Research Ltd (ORL)

The PM7000 portable monitor, the PM7503 panel mounted monitor and the PM7000 Fault Level Monitor have 4 current inputs and 4 voltage inputs while the PM3000 portable monitor has 3 current and 3 voltage inputs. All 4 different models record data using our patented Single Cycle Adaptive Store recording regime whereas the PM7000, PM7503 and PM7000FLM also have 3 other unique and distinct recording regimes:

Product

Standard Ground Lead for PP0x7 Series

PK007-002

-

Teledyne LeCroy

PK007-002 - Teledyne LeCroy

Standard ground lead for PP0x7 Series

Product

Hydrogen Frequency & Time Standard

CH1-1033

-

VREMYA-CH JS Company

CH1-1033 - VREMYA-CH JS Company

The hydrogen frequency and time standard Ch1-1033 is designed for precision storage and reproduction of the size of frequency and time units as part of measures and reference complexes. Main areas of application: – public service of time and frequency; – ground control complexes of radio navigation systems; – radio interferometry with extra long base.

Product

Standard Magnetizers

-

Magnetic Instrumentation Inc.

Magnetic Instrumentation Inc.

The selection of a magnetizing system begins with an analysis of the production requirements, including magnet material, magnet size, magnetizing orientation, number of poles, production speed, magnet measuring, and other operations that are necessary. After careful evaluations of these factors, and reviews of samples and/or drawings, our application engineers can recommend a system that will meet your requirements.

Product

Uniformity Calibration Standards

-

Gigahertz-Optik GmbH

Gigahertz-Optik GmbH

Integrating sphere light sources with halogen lamps or LEDs for generating luminous fields with uniform luminance distribution. Traceable calibrations of luminance or spectral radiance in the wavelength range from 250 nm to 2500 nm.

Product

Suitable For RTD Sensors Approved To ATEX And IECEx Standards

TTR200X -

-

Labfacility Ltd.

TTR200X - - Labfacility Ltd.

The TTR200X is our mid range transmitter for RTD or Slidewire sensors approved to ATEX and IECEx standards. It can accept many different types of RTD sensor such as Pt100, 500, 1000 etc and slidewire sensors up to 100K Ohm

Product

Rail Wheel Testing Using Phased Array System

ECHOMAC® PA Wheel Tester

-

Magnetic Analysis Corp

ECHOMAC® PA Wheel Tester - Magnetic Analysis Corp

MAC introduces two versions of Rail Wheel Testers using ECHOMAC® PA platform based on customer requirements. One is a semi-automated solution using local immersion technique. Used for tread inspection of new and/or reprofiled wheels. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread inspection. The second solution is a fully automated immersion tank. Performs tread and face inspection of rail wheels using two phased array probes simultaneously. This solution meets or exceeds EN13262, ISO5948 or AAR M-107/M-208 standards for tread and face inspection, while monitoring the backwall on the face side per EN 13262.

Product

Single Phase Multi-rate Static kWh Meter

SY 1035

-

Hong Kong Songyang Industrial Ltd.

SY 1035 - Hong Kong Songyang Industrial Ltd.

Adopt ADE7755 measurement chip. High accuracy class. Large overload times. Can sum up the absolute value of positive and negative energy. Record power energy of this month, last month, and the month before last.

Product

Additional Products: Standard Voltage 9 Pin D-Type Connectors

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

GFS Primary Gravimetric Flow Standard

-

Fluke Calibration

Fluke Calibration

The GFS dynamic gravimetric mass flow calibration system allows users to maintain the accuracy and traceability of molblocs or other high precision devices using the same primary reference used by Fluke Calibration. GFS is a true mass flow reference suitable for use in premier measurement institutes who require the lowest measurement uncertainty.

Product

Inductance Standard

1482 Series

-

IET Labs

1482 Series - IET Labs

The GenRad 1482 Standard Inductors are the standard of choice in metrology labs. Used today by national metrology institutes and primary standards bodies around the world, these inductors have no peer or equivlent.

Product

Standard Light Source

SLS-50W

-

Lisun Electronics Inc.

SLS-50W - Lisun Electronics Inc.

OSRAM Standard Lamp to calibrate the spectrum and luminous flux with Lisun Lab certification. The data can be traced NIM. The Standard Lamp Source is used to calibrate the integrating sphere system. The different size of Integrating Sphere should choose the right power of standard lamp source.

Product

Dual Channel HV Amplifier with Phase Inverter

A800DI

-

Pendulum Instruments

A800DI - Pendulum Instruments

This unit contains two independent A800 amplifiers that share common ground reference and power supply. Please see A800 page for technical details.It features also a low voltage phase inverter that inverts the signal applied to the input of channel 1. The resulting signal can then be connected to the input of channel 2 by means of a short BNC cable (supplied). As a result the two outputs operate in counter-phase.

Product

800MM 31.5In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles IP54 Standards

DL411

-

Advance Plus Trading Co., Ltd.

DL411 - Advance Plus Trading Co., Ltd.

Model Number: DL411 Key Specifications/Special Features: 800MM 31.5INCH Digital Level with level bubbles, 2 hand shanks, LCD bright backlight display, IP54 standards 1. 800mm 31.5inch level with 2 bubbles, 800*28*64mm（L*W*H）, net weight: 700g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. 2pcs Handshanks design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.