Voltage Amplifiers
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
Product
Isolation Amplifiers
-
Isolation Amplifiers provide power supply designers with a higher performing, single chip alternative to isolation techniques based on optocouplers and shunt regulators. Analog Devices ADuM3190 and ADuM4190 isolated error amplifiers have a 400 kHz bandwidth, with 0.5% typical initial accuracy at 25°C and 1% total accuracy over the extended temperature range of –40˚C to +125˚C. This provides manufacturers of ac-to-dc and dc-to-dc power supplies with a significant upgrade in speed and operating temperature range, as well as a 5× improvement in transient response.
-
Product
Voltage Detectors
JSC
-
The JSC family of devices provides a highly reliable way to determine if voltage is present downstream of the disconnector or circuit breaker knives during zero-energy shutdowns. They dramatically increase the safety of personnel performing maintenance on electrical equipment. When voltage is present downstream of the disconnector knives, one or more LEDs on the JSC-88A will remain illuminated. The JSC's compact design allows for direct installation on the disconnector door, starter, or control panel.
-
-
Product
Ytterbium-doped Fiber Amplifier
YDFA
-
Ytterbium-doped Fiber Amplifier (YDFA) is another Amonics specialised product line. Like our highly recognized optical amplifiers, the YDFA offers high output power and high gain with exceptional reliability. ideal for high power YDFA applications. The turnkey microprocessor controlled benchtop YDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition. Available options include single frequency operation, linearly polarized operation.
-
Product
Low Noise Amplifiers
WA Series
-
WA series low noise amplifiers are the balance type LNA with alarm capability in some of the products. Besides offering very low noise figure and wide bandwidth, the LNA have high linearity with unconditional stable design. The noise figures are from 0.40 dB to 1.0 dB and IP3 from 30 dBm to 40 dBm.The amplifiers cover the frequency bands of VHF, UHF, Cellular, GSM, DCS, PCS, 3G, C, and wireless LAN. The built-in alarm capabilities include Branch 1 and Branch 2 alarms, Soft Failure alarm, Hard Failure alarm, Soft alarm Open-Collector, and Hard alarm Open-Collector.
-
Product
40mA One-Channel Amplifiers
-
Piezo amplifiers/controllers are designed for high precision low to mid-speed positioning of low-voltage piezo actuators. These amplifiers are tuned for extremely high output stability and extremely low signal noise at the output. A low amplifier signal-to-noise ratio is very important because it determines the total resolution of the actuator. The nearly unlimited resolution of piezo-electric actuators using these amplifiers results in ultra-precise movement.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.
-
Product
Shortwave Power Amplifier
OM4001HF
-
The OM Power model OM4001HF is designed for all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands) and all modes. It is equipped with a two ceramic tetrodes FU-728F.
-
Product
Driver Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
Low frequency Amplifiers
-
Low-frequency amplifiersCurrent sourcesSystems with multiple amplifiersCustomized systems
-
Product
Switching Amplifiers
-
*One- or two-channel design*Small design requiring only very little space*Programmable output function*Relay or transistor outputs*Easy mounting on DIN rail
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
5B Measuring Amplifiers
MA Series
-
Highest aim of our connection technology is user-friendliness. Very comfortable is the connection of our products to the most various sensors and signals.
-
Product
Amplifiers
-
CAES manufactures custom amplifiers in a wide variety of configurations from LNA (Low Noise Amplifiers), Medium and High Power, and wideband solutions.
-
-
Product
Amplifiers
-
We have designed and manufactured amplifiers using all major semiconductor materials, LDMOS, GaN, GaAs, and InP, to produce narrow, wideband, and pulse, receive and transmit amplifiers from 1 MHz to 220 GHz and power levels from mW to over 10 kW.
-
Product
Amplifiers
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik GmbH offers a large portfolio of high performance broadband RF amplifiers. Optimized for linearity, high dynamic range and low noise, they cover all widely used radio standards like cellular, satellite radio, TETRA/BOS, GNSS, GPS, 802.11, including the new bands for LTE-U. They amplify wideband radio signals from shortwave over UHF, VHF up to 18 GHz in 50 Ohm technology (I-band, G-band, P-band, L-band, S-band, C-band and X-band). They are used as compact RF drivers, antenna pre-amplifiers or RF boosters in a variety of applications ranging from tunnel radio coverage extension, over airspace radio monitoring to in-ear monitoring and can also be offered as 1U 19” rack variants. Due to their advanced design, the power consumption is significant lower than typical industry alternatives, saving cost at customers with respect to cooling.
-
Product
Waveguide Amplifiers
-
VDI offers waveguide amplifiers for various applications. Waveguide amplifiers are able to boost a small input RF signal to a large output RF signal. For sample data on waveguide amplifiers, please refer to the Waveguide Amplifier Product Manual (also located under Resources). Please contact VDI for more information.
-
Product
Power Amplifiers
-
In this product category you find highly linear power amplifiers for digital and analog data transmission, power amplifiers for CW applications and for laboratory use, which stand out due to its liability, robustness and long-term availability and which are based on the semiconductor technologies which are actually available on the market.
-
Product
Analog Summing Amplifier
SIM980
-
Stanford Research Systems, Inc.
The SIM980 Summing Amplifier has four input channels that can be added or subtracted from each other. The output noise is less than 60 nV/√Hz, and crosstalk between channels is less than -80 dB. With a bandwidth of 1 MHz, a slew rate of 40 V/ms, and input offsets that are trimmed to ±100 µV, the SIM980 is extremely useful in many analog applications.
-
Product
The SoundCheck Amplifier
SCAmp Audio Test Amplifier
-
SC Amp is the world’s only dedicated audio test amplifier. Specifically designed for the audio test market, it incorporates several features unique to the needs of audio test and measurement, and unnecessary features found in regular audio amplifiers have been eliminated to keep production line operation simple and error-proof.
-
Product
Portable 4-Quadrant Power Amplifier
PIV270
-
PONOVO POWER's PIV270 Power Amplifier is equipped with feature of high power, large current, high voltage, high precision, high speed etc. It can meet different application on power and precision requirements.
-
Product
Amplified Noise Modules
NC1000 Series
-
The NC1000 Series amplified noise modules produce AWGN as high as +13 dBm, and have bandwidths up to 10 GHz. The high power modules are designed to test noise immunity for Cable TV equipment, secure communication channels, and military jamming systems. The lower power modules, <= 0 dBm, are random jitter sources for many applications including, PCIexpress, Infiniband, and 10 GigE.
-
Product
Power Amplifiers
-
Your ultimate solution for sound distribution in the contractor/install market.
-
Product
Voltage Stabilizer
MS 7643
-
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
Product
Amplifier Module
LNAM-B
-
Fully differential ultra-low-noise voltage amplifier module (LNAM) with selected bipolar rf transistors at the input stage. The amplifier exhibits ultra-low voltage noise, very high speed, and good dc precision. 50 Ohm input termination realized by negative feedback allows for the lowest possible noise temperature.
-
Product
RF Amplifier
SA812
-
Hangzhou Softel Optic Co., Ltd.
SA812 860mhz CATV outdoor trunk amplifier are mainly used for Bidirectional trunk transmission for CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
Product
Amplifier Gain Blocks
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a wide portfolio of Amplifier Gain Blocks for RF, microwave, and millimeter wave applications. Our amplifier gain blocks cover frequencies ranging from DC to 45 GHz. MACOM’s gain blocks are used in a variety of 50 Ohm and 75 Ohm applications including; Networks, Commercial and Aerospace and Defense. Leveraging the latest innovative technology these products are available in both standard plastic packaging and bare die.
-
Product
Separate Amplifier Pressure Sensor
AP-40 Series
-
Separate Amplifier Pressure Sensor. The industry's smallest and lightest air pressure sensor head, weighing only 7g. The super-small sensor head can be mounted close to the detection point decreasing response time.
-
Product
Variable Gain Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a broad family of Variable Gain Amplifiers (VGAs) for RF, microwave, and millimeter wave applications. Our VGAs cover frequencies from 50 MHz to 40 GHz and are used in a variety of Network, Commercial and Aerospace and Defense applications. These products are available in industry standard plastic packaging and are designed for both 50 Ohm and 75 Ohm applications.
