-
Product
OpenSpace QuantumTX
-
Kratos Defense & Security Solutions, Inc.
OpenSpace® quantumTX is a fully virtualized wideband software transmitter that addresses the needs of today’s current and next-generation of Earth Observation (EO) and Remote Sensing Satellites (RS) for more agile, cost-effective and scalable ground infrastructure.
-
Product
Franklin Tester
TF-100
-
The measuring device Franklin tester is designed to measure the insulation resistivity of coating and its mineral components on the surface of electrotechnical steel sheet as well as applied enamel to generator stator core laminations according to the ASTM A717/ A717 M - 95 Standard. The device contain series connection which allow the data transmittion to PC.
-
Product
Transmitter
MXT4
-
The C.Scope MXT4 Transmitter is designed for use alongside an MXL4 Locator. It enables a far more flexible approach to pipe and cable location enabling the operator to accurately detect, pinpoint, trace and identify the widest range of pipes and cables.
-
Product
Wet/Wet Differential Pressure Transmitter
655
-
The Series 655 Wet/Wet Differential Pressure Transmitter converts a positive or a positive differential pressure measurement into a standard 4-20 mA output signal. Designed for use as a wet/wet differential pressure transmitter, units can be used to measure gas or liquid pressures compatible with 316/316L stainless steel wetted parts
-
Product
Frequency Counter with Rubidium Timebase
SR625
-
Stanford Research Systems, Inc.
The SR625 Frequency Counter is a NIST traceable frequency counting standard for calibarating base stations, transmitters and many other types of communication systems.
-
Product
PSS Portable Oxygen Transmitter
OxyTrans-PSS
-
The OxyTrans-PSS uses a special micro-fuel cell to measure the oxygen concentration. The sensor meets the industrial requirements for accuracy, sensitivity, easy to use and has a long operating life.The calibration of the instrument for trace oxygen measurements in gas should be done with a known calibrated gas. The concentration can be chosen freely within the measuring range.
-
Product
Sonde Point Transmitter
-
Sondes are used to trace the path of non-metallic pipes and locate line blockages.
-
Product
Input High Temperature Liquid Level Transmitter
HR8005
-
HighReach Measuring & Controlling System Co.,Ltd
HR8005 input high temperature liquid level transmitter is used to measure the water level and water temperature change of high temperature surge well, digital temperature error compensation in full temperature zone, and store the compensation parameters in non-volatile memory.
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Active Antenna Combiner
M2C
-
The M2C active antenna combiner is designed as an ideal matching component to Lectrosonics digital transmitters. Up to eight transmitters can feed a single antenna to minimize cabling in multi-channel systems. The inputs are isolated to minimize crosstalk and IM (intermodulation) between RF channels.
-
Product
Humidity and Temperature Transmitter
T3111Ex-4
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Transmitter Control Subsystem (TCS)
Loran C Accufix 7500
-
USCG Loran Transmitter Control and Display stations modernized and upgraded to state-of-the-art processor controlled technology. Fully redundant system with comprehensive built-in performance monitoring. Automatic switchover upon detection of error, high single point failure tolerance. Long distance communications link supports remote station operation on a continuous basis. Built-in fault detection and monitoring enables dynamic re-allocation of failed subsystem modules, and fault isolation to major replacement assemblies.
-
Product
Advanced Monitoring Probe
DVB-C QAM
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-C and DVB-C2 signals at transmitter outputs, through its RF inputs (up to 4 in 1RU), as well as at modulator input and at Head-End/distribution links, through its ASI and IP inputs.
-
Product
High Powered External IP Transmitter
PowerSting
-
The PowerSting is a series of external high power transmitters (5kW, 10kW, and 15kW) for the SuperSting R8/IP/SP and SuperSting R1/IP/SP. The PowerSting system is a fully programmable constant voltage//constant current source. The PowerSting system comes with an SGS generator and a wireless repeater box, and operates in both wired and wireless modes. The applications of the PowerSting-SuperSting system include vertical electrical sounding, 2D electrical imaging, 3D electrical imaging, 3D offset electrical imaging of a 2D survey line in both manual and automatic modes.
-
Product
HFC 7 Ways Return Path Optical Receiver 1 Way Reverse Optical Transmitter
HR2071A, HR2071B
-
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2071 series of HFC seven-way return path receiver, one way reverse optical transmitter, mainly used at the head-end to convert upstream optical signal to RF signal at the user side. Moreover, send back the data at sub-HE to main head-end through one way of DFB return path transmitter. Eight independent units integrated into a 1RU 19" casing to provide service for HFC network terminal of ONTs. The receivers’ low noise design of -22dBm receive sensitivity, allow to supply service to farther distance. There are two versions of this receiver. HR2071A with LCD on the front panel, HR2080B without LCD. All receivers are temperature tolerance type can be installed in any network surroundings including out-door type. Both of these two types can adopt SNMP function, which can control the front panel to realize optimization work at the head-end and remote installment.
-
Product
Voltage Controlled GUNN Oscillators
GV-8 / GV-6
-
Voltage controlled GUNN oscillators provide optimal electronic tuning by coupling GUNN with tuning varactor. Oscillators provide low AM and FM noise, making them suitable as local oscillators or transmitters.
-
Product
Coupler
-
Couplers are RF passive devices used for coupling a specific frequency from inputted RF signal.This product is used for power level control of transmitter.
-
Product
4-20 mA Loop Powered Two Wire Oxygen Transmitter
OxyTrans
-
The Edgetech Instruments Model OxyTrans is an easy to use, accurate and economical way to measure Oxygen at trace and % levels. A simple display and one point calibration allows for a quick start of the instrument.
-
Product
VLF Receiver
T-Vlf
-
The VLF receiver is specially designed for high productivity surveys, in ground water and mining exploration. No orientation of the operator with respect to the direction of the transmitter is required since three magnetic sensors measure the components of the VLF field. Tilt or horizontality of the sensor unit is neither required since two inclinometers correct for tilted position.
-
Product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
-
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
Product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
-
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
Product
Temperature Transmitter
T4111
-
Transducer is designed for temperature measurement at C or F by means of an externaltemperature probe with Pt1000 sensor. Measured temperature is converted to linearized unified signal 4-20 mA. Measured values are displayed on LCD display. It is possible to switch OFF theLCD at all. Current loop has two-wire connection and requires power from evaluation device.
-
Product
Plug-In Temperature Transmitter
HR6200
-
HighReach Measuring & Controlling System Co.,Ltd
The HR6200 input-type integrated temperature transmitter uses an imported temperature sensor and output RS485 standard signals or 4 to 20 mA standard signals through a built-in microprocessor. The product uses a 316L stainless steel casing, and the temperature probe is placed at The front end, which can be customized according to the requirements of the user.
-
Product
Universal Differential pH Water Quality Sensors
SD7500CD
-
Continuous online pH monitoring in wastewater and coating industrial applications leads to contamination and eventually requires sensors to be replaced. A differential pH sensor utilizes a measurement technique designed to extend the working lifetime of sensors in challenging applications. Replacing the sensor reference (salt bridge) and buffered electrolyte solution can prevent sensor replacements, saving time and money. Our SD7500 Series features a combination sensor output; these differential pH sensors can be used with any conventional pH/ORP transmitter.
-
Product
Modbus Transmitter for LPPHOT01 Probe
LPPHOT01S
-
The transmitter LPPHOT01S converts the mV analog signal generated by the illumination probe LPPHOT01 into a digital signal suitable to be transmitted over a serial line RS485 with MODBUS-RTU protocol.
-
Product
Temperature Transmitter
T0418
-
For exacting interiors in building energy management and HVAC systems. Are designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets.
-
Product
Intrinsically safe humidity and temperature transmitter
T3110Ex
-
Built-in relative humidity, temperature sensors. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Radio Modules
-
Welcome to RF Solutions’ comprehensive selection of high-performance radio modules. We offer one of the widest ranges of reliable, innovative, and fast RF modules available online. Explore our extensive collection of transceiver radio modules, FM and AM transmitters and receivers, as well as the latest encryption integrated circuits (ICs).
-
Product
Power Meters & Power Sensors
-
Keysight’s power meters and power sensors measure the power of RF and microwave signals accurately with sensors of various types (CW, average, and peak and average), covering numerous frequencies and power ranges. We offer a wide selection of power meters and power sensors for nearly all application needs — wireless communications, radar pulse measurements, component test, and more. Applications include testing the output power of communication base-station transmitters, radar system equipment, wireless devices, and much more.
-
Product
RF Training Kit And Lab Sheets
Y1800A
-
The RF transceiver kit consists of a transmitter unit and a receiver unit in superheterodyne architecture. The transceiver units are made up of various RF building-block modules such as filter, low noise amplifier, power amplifier, mixer and oscillator. The RF transceiver kit is controlled by a Windows-based Control Panel software via USB. A Measurement Automation Program is provided to demonstrate automated characterization and test of RF circuits. A signal generator and a spectrum analyzer are required to run this program.
