PMC
PCI Mezzanine Card
-
product
PMC
LinkedHope Intelligent Technologies Co.,Ltd.
PMC is the de facto standard for mezzanine cards used in the VME, CompactPCI and VPX ecosystems. PMC offers system designers a reliable form factor with the high-performance of the PCI bus.
-
product
PMC Module
PMC-SCC04-IO
The PMC-SCC04-IO module is a Quad Channel serial communication controller with 64 Byte Fifo per line. The PMC-SCC04-IO is based on the XR17D154. The device support autoconfiguration registers for plug-and-play installation. This module provide 4 Asynchronous ports up to 6.125MBps .
-
product
Remote mount PMC
PMC-Extend-IO
PMC-ExtendIO-II provides a 32/33 - 64/66 extension between a PMC and Host. Any combination of PMC PCI bus speed and data width can be accomodated. With 66 MHz implementations cable lengths may be restricted compared to 33 MHz usage.
-
product
PMC Module
PMC-CycloneII-64LVTTL
User Programmable Altera Cyclone II FPGA 672 BGA, EP2C35, EP2C50, EP2C70, Stand alone possibility, Single wide PMC Module, 64 LVTL, Optional User clock oscillator
-
product
PMC Module
PMC-1553-PLX
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
product
PMC Module
PMC-MON16LED
• Fully compatible withGE Fanuc / RamixPMC498• PCI MezzanineCard (PMC) IEEE1386• 16 LEDs• Two RotarySwitches for 256Combinations• Read / Writeable• Monitoring LEDs• Front panel I/Oaccess
-
product
PMC-Parallel-485
The PMC compatible PMC-Parallel-485 design adds 32 [RS-485 /RS-422] differential IO lines to one slot of your carrier board. 2 additional differential pairs are available for a clock & clock enable. The signals can be used to capture data with an external reference or programmed to be references for the rest of the system.
-
product
PMC Carrier Card
APC-PMC
This board provides an easy and low cost solution that enables use of a PMC mezzanine I/O module in a standard PCI computer system. The carrier card acts simply as an adapter to route PCI bus signals to and from the PMC module through the PCI card slot edge connector.
-
product
PMC Carrier PXIe x4
Looking for a way to plug your PMC mezzanine card into a computing platform with a 4-Lane PXIe slot?Well, the CC_PXIeG1x4_to_PMC is your answer! It is effective, field tested and compliant with all applicable standards.
-
-
product
PMC Compatible Wizard Interface
PMC-Wizard
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
product
PMC Module
PMC-SCC04-IO
The PMC-SCC04-IOmodule is a QuadChannel serialcommunication controllerwith 64 Byte Fifo per line.The PMC-SCC04-IO isbased on the XR17D154.The device support autoconfiguration registers forplug-and-play installation.This module provide 4Asynchronous ports up to6.125MBps .
-
-
product
PMC
A PCI Mezzanine Card or PMC is a printed circuit board assembly manufactured to the IEEE P1386.1 standard. This standard combines the electrical characteristics of the PCI bus with the mechanical dimensions of the Common Mezzanine Card or CMC format (IEEE 1386 standard).
-
product
PCIe Carrier For PMC And PrPMC
PCI104
The PCI104 is a PCIe carrier for PCI Mezzanine Cards (PMC) or Processor PCI Mezzanine Cards (PrPMC). The PCI104 carrier allows simplified testing of PMC/PrPMCs and their associated PMC I/O Modules (PIMs) by using a PC environment during board development or deployment. The PCI104 can also reduce the costs of manufacturing PMC/PrPMCs by allowing manufacturers to use off-the-shelf PCs for functional testing. The PCI104 converts the PCIe x4 edge connection to PCI-X via a PCIe to PCI-X bridge. The trace lengths to the PMC/PrPMCare kept to a minimum so the PMC/PrPMC can run with a133MHz PCI-X clock speed. The J4 connector of the installed PMC/PrPMC is routed to a 96-pin DIN connector per theVITA-35 specification. The PCIe to PCI-X bridge can run in either transparent or non-transparent mode and can also operate in forward or reverse mode. The PCI104 has a fan mounted on the board to cool the PMC/PrPMC. The fan can easily be removed for testing and probing of hosted card.
-
product
PMC Carrier for 3U CompactPCI
TCP270
The TCP270 is a standard 3U CompactPCI carrier that provides front I/O and rear I/O for a single width PMC module. This PMC to 3U CompactPCI adapter is used to build modular, flexible and cost effective I/O solutions with PMC devices in CompactPCI systems.
-
product
PMC Modules
ARINC 429
Sycos range of ARINC 429 PMC modules offer the user up to 32 channels on a single width PMC module. Each channel can be programmed independently to operate at either high or low speed. Firmware options available for Tx Error Insertion and Rx Error Reporting are available.
-
product
PMC Module With 2 Or 4 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation Of Avionic CAN Bus Systems
AMC825-x
ARINC825 (CAN bus) Test & Simulation module for PMC with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AMC825-x PCI Mezzanine Card (PMC) can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
Video Mixer PMC
PMC-285
Curtiss-Wright Defense Solutions
The PMC-285 video mixer PMC is one of a range of video products from Curtiss-Wright Defense Solutions that facilitate the implementation of complex video systems, meeting the needs of systems integrators that have requirements for switching and routing video and for more complex operations such as multi-video windowing.
-
product
PCIe Adapter for PMC
PCIeBPMCX2
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
product
32-bit / 33 MHz PMC to PCI Adapter
4933
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
product
PMC SpaceWire
PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues
-
product
PMC Module
PMC-1553-TACEx
Operating temperatureCommercial: 0 to +70 °COptional: -40°C to +80°C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 20’000 ft
-
product
80-Channel Reconfigurable Digital PMC
2979
The 80-channel Reconfigurable Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring high speed single-ended operation. 64 of the 80 signals are available out the PN4 connector, while all 80 signals are wired to the front panel connector.
-
product
PMC-BiSerial II-NG1
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
product
cPCI to PMC Adapter / Carrier
cPCI2PMC
The cPCI2PMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCI2PMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation. The PMC user IO connector Pn4 is optionally connected to J2 for rear panel IO.
-
product
PMC Carrier with 2 positions
PMC-MC-X2
The PMC-MC-X2 adapter / carrier converter card provides the ability to install up to 2 (two) PMC cards into a small enclosure. The PMC-MC-X2 has one PMC card slot mounted front and rear to create a compact arrangement with 2 PMC slots. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
product
PCI Express x1 PMC Carrier
TPCE261
The TPCE261 is a standard height PCI Express Revision 2.0 compatible module that provides one slot for a single-width PMC module used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. The TPCE261 is a versatile solution to upgrade well known PMC I/O solutions to the PCI Express signaling standard.
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
Rugged Embedded MIL-STD-1553Conduction Cooled PMC Card
AMCE1553-x
Rugged embedded MIL-STD-1553 conduction cooled PMC card.
