-
Product
Memory Test System
T5835
Test System
The new T5835 has full testing functionality, from package testing to high-speed wafer testing, for any memory ICs with operating speeds up to 5.4 Gbps, including all next-generation memories from NAND flash devices to DDR-DRAM and LPDDR-DRAM. It can handle 768 devices simultaneously for final package-level testing. It additionally features functions such as an enhanced programmable power supply (PPS) for advanced mobile memories, and a real-time DQS vs. DQ function to improve yield.
-
Product
FPGA Test System
DO-254/CTS
-
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
Product
Test System
RF-1 ATS
-
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Circuit Breaker Test System
TDR900
-
It operates and records a circuit breaker’s contact timing, motion, velocity, main contact engagement & synchronization, trip and close coil initiation and currents.
-
Product
Fuel Cell Test Systems
-
Fuel Cell Test System is a complete test station for operation and measurement of PEM/DMFC fuel cells.
-
Product
Double Lift Zero-distance Drop Test System
KRD42 series
-
KRD42 series double lift zero drop tester is mainly suitable for large size packaging products to resist drop impact performance, its powerful power system and unique sample support for easy loading and unloading of oversized, overweight items, and automatically rise to the set height, complete the drop test.
-
Product
High Power & Voltage Pack Testing System
FTF
-
Drive simulations with standard Electric Vehicle tests: FUDS, SFUDS, GSFUDS, DST and ECE-15LDrive Cycle TestingIntegration with motor test benchesCycle testing of EV/HEV Battery Packs
-
Product
Portable Test System
MT686s
-
Actual value, vector, curve displaypower generationerror measurementMeasurement of harmonics up to the 40thVoltage supply via existing measurement voltage
-
Product
Automatic Tablet Testing System
UTS 4.3
-
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
Product
Vehicle Electromagnetic Field Test System
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are the daily means of transportation for our public, and the electromagnetic pollution in vehicles has received more and more attention from the public. The newly revised mandatory standard GB27630-201X "Air Quality Evaluation Standard for Passenger Cars" intends to require the electromagnetic field in the vehicle as one of the indicators. The measurement method measures the magnetic field strength in the vehicle. Within the frequency range of 10Hz-400kHz, the electromagnetic field measurement results should meet the requirements of the public limit of electromagnetic exposure in GB8702-2014.
-
Product
Test System Mainframe
ITC59000
-
The ITC59000 Test Platform is a desktop DynamicParametric Test System mainframe. The ITC59000Test Platform accepts up to four Test MeasurementUnits (TMUs) that perform transient measurements onsemiconductor devices such as power MOSFETs,IGBTs, and diodes.
-
Product
PXI Instrumentation Modules For Automated Test Systems
-
PXI-based test systems often require a variety of general-purpose instrumentation such as digital I/O, waveform generators, voltage & current sources and DUT power supplies.
-
Product
High Voltage Switching Test System
-
The advanced development of new technologies, such as SiC and GaN, have opened the opportunity for more efficient and higher voltage/power performance in switching and power management circuits. Their high cutoff frequencies, low on-state resistance, and very high breakdown voltages can increase power supply power handling densities approaching hundreds of watts/inch. Reliability of these new technologies and techniques is critical for realizing practical applications. While Silicon devices have a rich history of proven reliability, these newer compound semiconductor technologies are too new to have a reliability history and have not been well proven. Further, process variations, even in well-controlled lines, yield widely varying results. This has driven the need for additional testing and to burn-in devices prior to delivery.
-
Product
FADEC/EEC Test Platform
Test Platform
The FADEC/EEC Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of full-authority digital engine control (FADEC) and electronic engine control (EEC) units of both rotary- and fixed-wing airframes. The system simulates one or more turbofan engines, including its sensors and actuators for use with the most sophisticated FADECs and EECs on the market. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
Product
Electrodynamic Vibration Test Systems
PET-series
-
Vibration controller: Enables complicated vibration tests being coupled with the vibration controller.
-
Product
Circuit Breaker Test Systems
-
Crest has over a decade of experience of designing and manufacturing test systems for testing all the different kinds of switchgear and controlgear.
-
Product
Measurement System For Testing & Binning Of Back-End LEDs
TP121-TH
-
The photometric specifications of LEDs must meet very high tolerance requirements regardless of whether they are to be used in general, automotive or other specialist lighting applications. This is often a problem since the manufacturing tolerances of LEDs can be higher than those permitted in the end-use applications. Also, LED binning by LED manufacturers in order to classify LEDs based on their tolerances is performed with flash mode testing using pulsed current flow. However, end-use applications of the LEDs often operate in constant current mode and with significant thermal effects. The sophisticated LED processing industry therefore requires measurement devices that can be used for both manufacturer-compliant pulsed mode, as well as constant current operation mode. When the LEDs are run in constant current mode, the junction temperature has significant influence on the performance and lifetime of the LED. Therefore, test systems should be able to test the LEDs at specific junction temperatures.
-
Product
Wireless System For Test And Measurement
TM400 Compact
-
The TM400 system was designed to provide the ideal link between calibrated test microphones and measurement equipment such as SIM®, SIA SMAART Live®, TEF® or other systems. By using a radio link, long cables can be eliminated thus saving time and providing opportunities for additional measurements to increase accuracy. The microphone can even be moved around in the venue while the audience is present – something that is impossible with a cabled measurement microphone.
-
Product
Lamp Cap Temperature Rise Test System
CX-T1
-
Shenzhen Chuangxin Instruments Co., Ltd.
Lamp Cap Temperature Rise Test System is according to IEC60360-1998 and GB2512-2001(Standard method of measurement of lampcap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards
-
Product
High Power LED Test System
Lumere-GM
-
Evolusys Technologies Sdn. Bhd.
Lumere GM is a LED test and measurement system for various parameters of LED light. It is a high-accuracy system with a temperature-controlled CCD, its geometry conforms with CIE-Publication 127, and the test program is easy to configure and adjust. The Lumere GM is used in laboratory applications and in the production of high-power LEDs.
-
Product
ESD & Latch-Up Test System
-
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Product
Pneumatic Horizontal Shock Test System
KRD12 series
-
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
Product
Test Case Management System
Kiwi TCMS
-
The leading open source test case management system. *Efficiently manage test cases, plans and runs*Improve testing productivity & reporting*Integrates with popular issue trackers*External API interface*GPL 2 licensed
-
Product
Horizontal Vibration Test Systems
G-3 Series
-
This series was used for the special structure of airbearing guide of inspection for Seismic Detectors andcharacterized is large displacement and high-accuracywaveform. In addition, the use of the Windows seismicdetector controller is easy to operate it.
-
-
Product
Environmental Test Systems
-
Manufactured products can be exposed to both thermal and mechanical stresses.These should not be considered separately, as the effects may be linked.IMV can supply vibration-test systems combined with climatic chambers to provide complete vibration, temperature and humidity environmental testing.These systems can be custom-designed to meet your application.
-
Product
Ice Profiler
IPS
-
Estimate ice forces for design of offshore platforms and operational planningDetermine the extreme thickness of ice for pipeline installationsExamine in detail the underside of sea-iceUnderstand the dynamics and thermodynamics of the sea ice regime for scientific research.Climate change studies
-
Product
16-Station Testing System
-
The ElectroPuls 16-Station testing system performs high cycle fatigue testing on multiple samples simultaneously, with a fatigue-rated load cell included on each station. The fixture uses a carousel designed with high stiffness and low mass to enable high frequency testing and reduce test time.
-
Product
(1000kN) Fatigue Testing Systems
8805
-
The 8805 is a 4-column, 1000 kN servohydraulic fatigue testing machine. It features a high-stiffness and precision-aligned load frame, with hydraulic lifts and locks, and an actuator in the upper crosshead.
