CompactPCI Chassis
A metal frame that serves as the structural support for a CompactPCI bus. (sbc.webopedia.com)
-
product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
product
6 Slot PXIe Based Chassis with Embedded Controller
PXE6410
The PXE6410 is a PXIe based 6 based slot Gen 3 x4 chassis, that supports the Tabor Proteus Family of AWG’s and the TE330x family of PXIe RF amplifiers. The Chassis allows you to purchase any Proteus PXIe module and later add or up-grade to more channels, higher sample rates or higher output power.
-
product
Chassis - Built as 60 or 75 ohm Matrix Configuration Switch Modules for High Bandpass
CXG Matrix
These Chassis are built as 50 or 75 ohm matrix configurations of 4x8 or 8x8 using tree switch configuration switch modules for high bandpass. The internal matrix block is wired out to BNC, SMA or other 50 or 75 ohm connectors. LEDs on the front panel show switch and power status. Add a Control Module to complete the system.
-
product
2-Slot USB/LXI Modular Chassis
60-104-001
This 2-slot USB/LXI modular chassis offers a small lightweight form factor, making it ideal for portable, benchtop, and space restrictive applications. The chassis is designed for desk or rack mounting and features remote control via USB or LXI Ethernet. Remote control over a network enables the switching function of a test system to be located as close as possible to the target equipment. The 60-104 chassis supports one or two 3U PXI modules and accepts Pickering's PXI products, it is the perfect platform to construct small scale applications. Possible systems include switching matrices up to 1104 crosspoints, 396 channel multiplexer or up to 36 channels of programmable resistor/sensor emulation.
-
product
cPCI Serial Chassis 4 Slots
4U 32HP
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 4 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 4 slot PCIe Gen3 backplane with full mesh topology, powered by a 180W ATX power supply.
-
product
cDAQ-9184, 4‑Slot, Ethernet CompactDAQ Chassis
782069-01
4‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9184 is a CompactDAQ Ethernet chassis designed for small, remote, or distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use a combination of modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers built in. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement. With multiple timing engines, you can run seven hardware‑timed operations simultaneously, with three independent rates for analog input.
-
product
Eighteen Slot PCXI/PXIe Full Hybrid ABex Chassis with up to PCIe x4 Connectivity on Each Slot
ABex PXIe Rack 18
Fully featured 7U ABex chassis with 18 slots. This variant allows maximum flexibility and upgrade possibilities. The 18 slot PXIe/PXI hybrid backplane supports also large-scale embedded PXIe controller that requires up to three additional slots on the left side. In addition, Konrad PXIe embedded controllers or MXI interfaces are supported. The ABex PXIe Rack 18 can be combined with a robust VPC interface system.
-
product
PXIe-1088, 9-Slot (8 Hybrid Slots), Up to 8 GB/s PXI Chassis
784782-01
PXIe, 9-Slot (8 Hybrid Slots), Up to 8 GB/s PXI Chassis - The PXIe-1088 features an all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
product
CXAR Custom Chassis
Cytec has a complete metal fabrication shop and a laser etching machine so we can build custom systems with very low NRE. Module arrangement, custom labeling, custom configurations are done fairly easily and nearly 50% of the systems we build are not shown in our standard product line. Don't see what you need? Just ask!
-
product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
product
14 Slot, 3U, 350W, PXI Chassis - 3 Speed Fan Option
40-914-101
This PXI chassis includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 13 more 3U peripheral modules.
-
product
PXIe Chassis: 18-slot, 3U, 24 GB/s, Gen 3
M9019A
The Keysight M9019A PXIe 18-slot Gen 3 chassis delivers the flexibility, compatibility, and performance required for demanding applications. With 16 PXIe hybrid slots, it gives the system designer more flexibility to mix and match the number and location of PXIe and hybrid-compatible modules. The ultra-high performance, PCIe switch fabric can operate up to Gen 3 providing up to 24 GB/s of system data bandwidth. Combine the M9019A with the M9022A/23A/24A PXIe System Modules and M9048B/49A PCIe Desktop Adapters to achieve up to a Gen 3 x16 PCIe link to an external PC.
-
product
NI-9159, 14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis
781315-01
14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis - The NI‑9159 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9159, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9159 chassis in a single chain and connect up to eight chains to a single controller.
-
product
CompactPCI
CPCI-ADDA
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
product
2U Wall-Mount/Tower Embedded Mini-ITX Chassis With One Dual Expansion Slot
RK-200I
- Supports one dual slot expansion card(Low Profile)- Reserved for 2 USB, 2 COM, and 2 antenna punchouts.- One 3.5” drive bay and one 2.5’’ drive bay. (Compatible for three 2.5’’ drive bays)- 8cm two ball bearing PWM fan ( 42.5 CFM)- Support both Flex ATX power supply & AC-DC power adaptor
-
product
PXIe Full Hybrid Chassis, 18-Slot (Gen 2)
42-926-001
Our 42-926 high-performance PXIe Chassis provides one PXIe system slot, one PXIe timing slot and 16 hybrid compatible slots for application flexibility. The chassis utilizes a single PCI segment with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI-specific high accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane.
-
product
Chassis - up to Two 8x1 Modules, Four 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration
CXAR/16-MF
These Chassis controls up to two 8x1 modules, four 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton Manual control is optional.
-
product
PXIe-1086DC, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis
787137-01
PXIe, 18-Slot (16 Hybrid Slots, 1 PXI Express Slot), DC Power Supply, Up to 12 GB/s PXI Chassis - The PXIe‑1086DC incorporates hot-swappable, redundant DC power supplies as well as hot-swappable, front-accessible, redundant cooling fans. These high-availability features improve the mean time between failure (MTBF) and mean time to repair (MTTR) of the PXI system. The PXIe‑1086DC monitors power supply health/voltages, air intake temperature, and fan health/speed; it provides any failure feedback with the status LEDs located on the chassis. This chassis is ideal for test, measurement, and control applications with demanding system uptime requirements.
-
product
NI-9154, 8-Slot, Virtex-5 LX50 FPGA, MXI-Express CompactRIO Chassis
782457-01
8-Slot, Virtex-5 LX50 FPGA, MXI-Express CompactRIO Chassis - The NI‑9154 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9154, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9154 chassis in a single chain and connect up to eight chains to a single controller.
-
product
AXIe 5-Slot Chassis
M9505A
The M9505A AXIe Chassis is fully compatible with the AXIe 1.0 specification. It includes an embedded system module (ESM) that does not take up an instrument slot. This system module performs the chassis management functions contained in the AXIe specification. Additionally, it provides PCI and LAN interfaces for connection to an external computer, external clock and trigger connectors, and Keysight-exclusive, inter-chassis synchronization connectors. The local bus implemented in the M9505A provides the maximum 62 pairs allowed by the AXIe specification. Combine the M9505A with the M9048A PCIe Desktop Adaptor to achieve the highest system bandwidth.
-
product
12-Slot PXI chassis
PXCe4012
The PXI chassis of the PXC family are very space-saving, since the measuring cards are installed horizontally instead of vertically in contrast to the usual PXI chassis. Instead of the usual 4-6 U, only 1/2 U are required in the test system.
-
product
3U / 6U PXIe Chassis
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
product
PXIe Chassis: High-Power, 18-slot, 24 GB/s
M9046A
The Keysight Technologies, Inc. M9046A PXIe 18-slot chassis delivers the power and cooling required for high-performance applications with 3 PXIe hybrid slots and Gen 3 backplane (maximum 24 GB/s system and 8 GB/s slot-to-slot) with a two-link (x8, x16) system slot and x8 links to the PXIe slots
-
product
PXI Chassis, 19-Slot
40-923A-001
The 40-923A includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 18 additional 3U peripheral modules.
-
product
cPCI Serial 4U 84HP 9 Slots
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by two 300W cPCI Serial power supplies.
-
product
CompactPCI Serial Chassis
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections. CompactPCI Serial was officially adopted by the PCI Industrial Computer Manufacturers Group PICMG as PICMG CPCI-S.0 CompactPCI Serial in March 2011.
-
product
Chassis
With over 20 different chassis configurations, our Smart PXI chassis product line (3U chassis, 6U chassis, 3U/6U chassis) offers the most features, slot configurations, UUT interface options, system power, and embedded / external controller options in the industry.
-
product
CompactPCI Boards
*CompactPCI (cPCI) boards are 3U or 6U boards connected via a passive PCI (Peripheral Component Interconnect). Up to 8 boards can be connected together in a segment. Segments can be connected through bridges. *They are grouped into four categories: CPU, Communication, Input/Output, PMC carrier.
-
product
14-Slot Combination PXIe Chassis
GX7100e Series
The GX7100e Series are 14-slot combination PXIe chassis that accommodate a 3U PXIe embedded controller or a MXI express controller as well as 3U & 6U PXI / PXIe insruments in 4U of rack space. The GX7100e’s unique format includes seven 6U slots and seven 3U slots arranged horizontally to reduce the overall size of the chassis, providing the versatility and high-density necessary to address many PXI / PXIe applications and requirements. The backplane architecture supports Gen 2, 4x4 PCI Express bus signaling and the use of both x1 or x4 system controllers. By offering a combination of PXI-1, Hybrid, and Express slots, the GX7100e offers users the ultimate in flexibility for general purpose as well as high bandwidth test needs.
-
product
19-Slot 3U PXI Chassis with AC
PXIS-2719A
The ADLINK PXIS-2719A is a 3U PXI chassis with a series of advanced features:*An innovative cooling mechanism to deliver efficient and uniform heat dissipation*Superior stability within an extended temperature range*Intelligent chassis management that dynamically monitors and manages fan speed, system voltages, and internal temperature*Remote management via standard RS-232 monitoring port
