Magnetic Field Meters
Measure magnetic flux density/field strength.
See Also: Magnetic Field, Magnetic Field Mapping, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test
-
Product
EMC Near Field Probes
TBPS01
-
The TBPS01 EMC near field probes H20, H10, H5 and E5 are magnetic field (H) and electric field (E) probes for radiated emissions EMC pre-compliance measurements. The probes are used in the near field of sources of electromagnetic radiation.
-
Product
Measuring Device For Measuring Residual Magnetism
Teslameter M-Test LL
-
Measure residual magnetism on ferromagnetic materials precisely and reliablyquick detection of residual magnetismreproducible measurement results through automatic storage of the maximum valuesdefined measuring distance of 0.5 mm from the Hall probe to the measuring surfacemeasuring static and alternating magnetic fieldsselectable units: A / cm, Gauss, mTwear-resistant test sample
-
-
Product
Hand-hold Field Intensity Meter
LM870-N
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Spectrum displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
Product
Complete Field Meter Site Testing Solution
7 Series
-
We raised the industry standard by introducing the PowerMaster 7 Series as a true 3-phase analyzing reference standard with internal 3-phase current and voltage source capability. The innovative design of the PowerMaster® 7 Series allows utilities to fully test a metering installation with one piece of equipment. Customer load meter testing, phantom load meter testing, CT burden and ratio testing, CT de-magnetization, PT ratio testing, and transducer testing can all be performed with one solution. In addition, vector diagrams, voltage and current waveforms, and harmonics data up to the 100th harmonic can all be analyzed to complete a true wiring verification.
-
Product
Polarisation Mode Field Diameter
MA500
-
MA500 is our polarisation mode field diameter (MFD) and effective area (Aeff) measurement system, specially designed to measure large effective area and high NA single mode fibers with its enhanced dynamic range and high-resolution scanning optics.
-
Product
RFID-Coded and Magnetically Coded Safety Sensors
-
- Actuation possible from different directions- Meets the interface description CB24I from ZVEI- Can be connected in series- Conceal behind stainless steel for enhanced tamper prevention- Meets highest safety levels to ISO 13849-1 and SILCL 3 to IEC 62061
-
Product
Meters
-
Get a precision DMM, a touchscreen display, and fast, accurate digitizer: the Keithley DMM7510 7½-Digit Multimeter.
-
Product
Cryogenic Low Noise Magnetic Field Transducer
K3A
-
The SENIS K3A cryogenic low noise magnetic field transducer is engineered to deliver highly accurate measurements of the amplitude and direction of magnetic fields at extreme cryogenic temperatures, extending down to approximately 1 K. This innovative instrument features a compact sensor head boasting dimensions of just 4.5 x 4.5 x 9 mm, integrating a robust 3-axis Hall sensor that guarantees precision in magnetic field readings. Notably, it incorporates the world’s smallest field-sensitive volume, measuring less than 0.6 mm³, making it a premier choice for applications requiring compact and efficient magnetic field measurements.Equipped with cutting-edge electronics, the K3A transducer provides exceptionally low drift and ultra-high resolution in its measurements. The device outputs an analog voltage for each magnetic field direction (Bx, By, Bz), facilitating accurate assessment of magnetic fields. Optional high precision calibrations are available, achieving an impressive accuracy of 0.25% and accommodating magnetic fields up to ±9 T, even at cryogenic temperatures as low as 4 K. This instrument is ideal for researchers and engineers needing reliable and precise magnetic field measurements in challenging environments.
-
Product
MCB Thermal + Magnetic Characteristic Test Bench
-
The test system is a special version of the thermal + Magnetic test test system. The single power source able to deliver either thermal or magnetic test parameters set on the PC by the user.
-
Product
Field Machine
-
The Portable Field Machine is our most versatile full specification corrosion testing instrument. Its rugged construction and protective water resistance IP68 enclosure enables it to be operated at extreme locations throughout the world. This instrument takes laboratory precision outdoors to oil rigs, pipelines, concrete walls and just about anything that needs corrosion monitoring in situ. The potentiostat, ZRA, integral Frequency Response Analyser and Sweep Generator are exactly as provided in the laboratory Gill 8 model ensuring the most accurate testing available. The choice of tests is not limited; the AC, IR Compensation and DC tests plus the Sequencer and Analysis that are supplied with this field instrument are the same as supplied with the laboratory instruments.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1A
-
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Magnetic Particle Flaw Detector
MT-1C
-
MT-1C magnetic particle flaw detector adopts high-capacity lithium battery pack, can convert DC to AC through variable-frequency, provide magnetic powder flaw detector with magnetic power supply. With low power consumption, it can continuous work for more than four hours after charging. It is especially proper for working in the wild and aerial area.
-
Product
Photonic Electric Field Sensor System
Model No. 200-04
-
SRICO Model No. 200-04 Photonic Electric Field Sensor System has the ability to measure electric field with minimal disturbance to the field. The lightweight fiber-optic cables allow for easy placement of the E-field probe, allowing it to be unencumbered by the use of heavy coaxial cables that may disturb the field being measured. The dielectric E-field probe is electrically passive.
-
Product
Field Installable Connectors
-
Factory terminated and polished to make fiber terminations fast, easy and reliable.
-
Product
Frequency Conversion Rotating Magnetic Fla
MT-2XCF
-
MITECH MT-2XCF rechargeable frequency conversion rotating magnetic flaw detector is based on principle that the leakage magnetic field can absorb the magnetic powder. Make use of magnetic yoke magnetized the workpiece of ferromagnetic material. If there has defects it will produce leakage magnetic field that will adsorb magnetic powder. We could detect the flaw by observing the density of adsorption magnetic powder. It adopts large capacity lithium battery. By the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 6 hours. And the battery can be charged when the detector is on and off. Especially suitable for the field testing. It can choose the current frequency according to the flaw depth with unique frequency conversion communication design, that improve the detection sensitivity. It’s widely used in aircraft manufacturing, boiler and pressure vessels and other fields. It is a necessary professional precision instrument of quality control, in-service safety monitoring and life assessment.
-
Product
Vector Field and Multi-Axis Systems
-
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
Product
Probes, Magnetic Field
EM-6880 | 9 KHz – 520 KHz
-
The EM-6880, EM-6881 and EM-6882 Magnetic Field Probes operate in conjunction with any 50 ohm input impedance receivers.
-
Product
Cryogen-Free DR With Integrated Magnet
-
Magnet thermally linked to cryocooler 2nd stage Ideal for smaller magnets up to 17 T or small vector magnets up to 7T / 2T / 2TSingle pulse tube cryocooler for cooling both magnet and DRMagnet operation at 700 mK or 4 KUse with top-loading probeFast Sample Change
-
Product
Magnet Testing
m-cat
-
m-cat is a magnetic field mapper for magnetrons which measures the magnetic stray field data of magnetrons on all three spatial axes and also calculates geometric data. This allows sputtering processes to be monitored and optimized, since the setting or status of the magnetron is critical to the subsequent outcome of the coating process.
-
-
Product
Handheld Meters
-
Omega carries a wide variety of handheld meters including anemometers, temperature and humidity meters, clamp meters, vibration meters, gauss meters, hardness meters and many more.
-
Product
L20 Meters
Model L20 pH/ORP
-
The Model L20 pH/ORP/Temperature meter is an AC line powered or battery powered precision instrument. The Model L20 features auto buffer recognition during calibration for both USA Standard and NIST pH buffers. The L20 has automatic temperature compensation and it monitors the electrode’s slope and offset reporting the electrodes efficiency assuring that the measurement is correct.
-
Product
pH Meters
-
pH meters are used to measure the acidity and alkalinity of liquid or semi-solid samples across many industries, this device has ORP measurement that is widely used in aqueous samples such as oil emulsions, unclean water it is majorly applied in waste water, drinking water, food and beverage, chemical and pharmaceutical testing.
-
Product
Digital ESD Field Meter
FM-1126
-
Now with an ionizer probe attachmentIndicates voltage and polarityDigital display is updated every three secondsNon-contactPower on/hold and zero buttonsEasy to read 3.5" LCD displayRange: 1-20,000v1" spacer bar9v batteryLeather case includedProduct conforms to the ESD S.20.20 spec standardsChecks for class zero conformance
-
Product
Broadband Field Meter
NBM-550
-
*Intelligent probe interface detects probe parameters*Fully automatic zero point adjustment*Memory for saving up to 5,000 measurement results*PC software for convenient data management*Voice recording for comments*Conditional logging: Measured value saved when a threshold value is exceeded
-
Product
Analog Meter
-
Basic functions:DC current: 2.5/25/500mADC voltage: 2.5/10/50/250/1000VAC voltage: 10/50/250/1000VResistor: R x 1/R x 10/R x 100/R x 1000Special functions:Continuity buzzerLow battery displayMulti-protective circuitGeneral characteristics:Color: yellowNet weight: approximately 130gWindows size: 75x57mmSize: 123x84x34mmPower: 2 x 1.5V, 5#Packing contents:360Trx analog meterPacking cartonEnglish manualTest leadPacking:Carton size: 440x355x275mm
-
Product
Electric Meter
DDS38
-
SHANGHAI POWOO INDUSTRY CO., LTD
The DDS38 single phase static watt-hour meter is designed for measurement of electric energy flowing in one or two directions in households and at commecial customers in single phase 2 wire networks. It complies with IEC61036 standard and is manufactured in compliance with the ISO9001 standard.
-
-
Product
Haze Meters
-
Shenzhen ThreeNH Technology Co., Ltd.
3NH offers a wide range of haze meters. They include various benchtop and portable models. Our haze meters are specially designed for testing haze, transmittance, and clarity in glass, plastics, films, and transparent packaging materials.
