Primary Current Injection Test
-
Product
Current And Voltage Input Sensors
-
Current input sensors monitor current from inverters in solar panel and wind turbine applications and turn the current into voltage which can be measured with an analog input type data acquisition module for analysis. Voltage Input Attenuators can be used to measure high voltages. Voltage Attenuators are designed for used in high-voltage applications. The current can be converted into +/-10 Vpp attenuated signal, so that a general electronic measuring device is able to read the signals.
-
Product
High Current DC Transformerd
-
High Current DC Transformer provides very accurate DC current measurements up to 3000 A with output current that varies directly with the input current in three ranges. This direct current transformer is designed with an open window to pass a single cable, set of cables, or buss bar that carry the direct current to be measured.
-
Product
DC Precision Current Sources
-
DC Precision Current Sources provides precise and very stable output currents from 3 A to 10,000 A. The 6623A-PCS Series provides the best uncertainties of any DC high current sources (i.e. < 5 ppm of precision and stability at 1000A). In addition this Series is modular and initial output currents can be expanded at any time.
-
Product
Voltage, Continuity & Current Tester
T5-1000
-
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
Product
Primary & Secondary Current Injection Testing Sets
-
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
-
Product
Communications Test System for Frontline Diagnostics
ATS3000P
Test System
The ATS3000P is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000P also includes the sophisticated IF and baseband I/Q DigitalSignal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easyto-use graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets are available for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Generator Of Direct Current And Voltage
GPTN
-
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
Product
NI-9208, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
785041-01
Current Input Module
500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The NI‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The NI‑9208 uses a standard D‑SUB connection for use with cables and connector blocks.
-
Product
Current Probes
-
Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.
-
Product
Current Input0 to 20mA
TGPR-0804
-
Current input data logger. A current input data logger that is housed in a robust, waterproof (IP68) rated case. The TGPR-0804 can be used to record the output from a number of industry standard 4-20mA sensors. Common applications include pressure and flow rate monitoring.
-
Product
Fuel Injection Tester
FIT13APB
-
This basic fuel injection tester includes large and small Schrader adapters, M6-1.00 O-ring adapter, and tee manifoldIncludes everything necessary to test the following systems: American Motors; Bosch AFC, MPC European and Japanese (except CIS- use our FIT447); Chrysler Corporation; Ford Motor Company; GM (except TBI- use our FIT446)
-
Product
Current Transformers
Sensors
-
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
-
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
Product
Current Meter
MTD32
-
The mezzanine module (mezzanine) MTD32 is designed to measure instantaneous current values over 32 channels.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-800B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
Current Clamp Adapter
-
PeakTech Prüf- und Messtechnik GmbH
It uses a pair of jaw which allow clamping around an electrical conductor to measure the current in a conductor without the need to make physical contact unlike a normal multimeter.
-
Product
Current Compression Flexure Testing Machine
CST-300/200
-
Jinan Testing Equipment IE Corporation
The Compression and Flexure Testing Machine is mainly designed for compression and bending tests of cement & mortar specimens. The Compression and Flexure Tester for Current can finish compression and flexure tests automatically by one-key action . Computer & software are also adopted to make the operation even easier. With new design and advanced technology, the series of Compression and Flexure Testing Machine have more advantages in appearances operation & applications. The Compression and Flexure Tester for Cement is an ideal tester for quality control at industrial & mineral enterprises, teaching in high schools, and technology researching al scientific industries.
-
Product
True RMS Current Clamps
-
PeakTech Prüf- und Messtechnik GmbH
Current clamps are ideal for current measurement in electrical systems and control cabinets, since only single wires are guided through the clamp jaws for contact-free current measurement and no electrical connections have to be disconnected. In addition, this model has extensive multimeter functions for voltage, resistance, frequency, capacitance and temperature measurement.
-
Product
High Frequency Current Transformers
-
Osborne High Frequency Current Transformers operate at frequencies higher than 50/60 Hertz. Their purpose is to reduce high frequency system currents to lower values that are appropriate for instrumentation and/or protection circuits. They have been designed to meet specified current ratios, and burden impedance at a specified transformation error. One area of unique Osborne expertise is in designing for phase shift when high frequency current transformers are to be used for power measuring applications.
-
Product
Integrated Two-Stage Current Sensors
-
If ultra-low noise performance is required, our integrated two stage devices are the number one choice. With input inductances from 24 nH to 1.8 µH and a flux-noise level as low as 0.8 µPhi0/sqrt(Hz) an energy resolution of about 45 h is attained. The devices consist of a 16 SQUID series array as amplifier stage and a single front-end SQUID.
-
Product
Pressure To Current Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Compact solution for testing Battery Packs with output power up to 110 kW and voltage range up to 1500 V
-
Product
Current Transformer Analyzer
CT Analyzer
-
Current transformer testing in a multifunctional instrument performing excitation, ratio, polarity and winding resistance tests on current transformers as well as burden impedance measurement.
-
Product
Current Transformer
ST-60CT
-
Standard Electric Works Co., Ltd
● 400/5A - 800/5A● 7.5-10V A● Class 1● Insulation 600V
-
Product
Current Sensors and AC Current Sensors
-
Current sensors are designed to monitor the presence or absence of AC or DC current and are available in an assortment of standard & custom models with hermetic or gasket seal models designed to withstand severe environmental conditions.
-
Product
Compact Functional Test System
E2230C / TS-5040
Functional Test
The Keysight TS-5040 functional test system is a robust, and reliable test system that ensures an economical ownership experience. When coupled with Keysight software such as KS8400A PathWave Test Automation with KS8328A PathWave Test Executive for Manufacturing (PTEM) or TestExec SL with TS-5000 libraries, it provides a streamlined development process and accelerated deployment. The TS-5040 seamlessly integrates into heavily automated production areas. It is a minimalistic one-box solution for automotive and industrial applications that saves valuable rack and floor space.
-
Product
Scienlab Battery Test System – Pack Level, 110 KW Compact Version
SL1710A
Test System
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
Product
Current Dataloggers
-
With our selection of current data loggers, you can meet requirements that include the single/split phase, three-phase, neutral, ground current and machine load monitoring. You can also utilize our current loggers for fault current detection, leak identification, and load profiling. We have compact models constructed to be weatherproof. Choose from stand-alone, handheld and clamp-on configurations. Our current data loggers are used in a broad scope of applications, trusted by technicians, electricians and engineers.
