Solar Reference Cells
See Also: PV Cell, References, Photovoltaic Reference Cells, Solar Simulators, Solar Irradiance
-
Product
Frequency Reference
E8-X
-
The Quartzlock E8-X is a breakthrough in exceptionally low cost, miniature, traceable, calibration-free, off-air frequency & time standards. These references maintain the high frequency & time accuracy required for demanding applications.
-
Product
Portable Engineered Test Cell
PET
-
PET is an innovative portable engine test cell. Most test cells are designed by an architect and built of conventional materials like bricks and mortar, making the cells immovable and inadaptable to changing requirements. Emprise has developed a practical alternative to this PET a portable and modular engine and component test cell.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Single Point Aluminium Load Cell
EST-2
-
Technopark Automation & Control
The EST-2 is a Single Point Aluminium Load Cell suitable for use on platform scales measuring 400x400mm. This load cell is available in capacities from 3kg to 100kg.
-
Product
Bending Beam Load Cell
EST-7
-
Technopark Automation & Control
The EST-7 is a Bending Beam Load Cell suitable for use on lower capacity weigh hoppers, filling machines, packaging machines and conveyor belt scales. This load cell is available in capacities from 10 kg to 200 kg.
-
Product
nVision Reference Recorder
-
AMETEK Sensors, Test & Calibration
Accurate enough to replace a deadweight testerRugged enough to sit in 3 feet of waterPortable enough to complete calibrations anywhere
-
Product
Test Cells
Emissions
-
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They \re calibrated according to the methodology of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing.
-
Product
Cell Site Test / BBU
-
VIAVI mobile base station test solutions are the industry’s most comprehensive and cost effective for installation, commissioning, and maintenance.
-
Product
Highly Collimated Solar Simulators
-
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
Product
Solar Simulator
-
It is the optimum light source for the evaluation of requiring high degree of parallelism close to sunlight. Irradiation area and parallelism are produced according to your request.
-
Product
AC Reference Generators
SR23
-
Computer Conversions Corporation
The SR23 Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation (2-115VAC) to synchros or resolvers in military and industrial control applications. They accept +/-15V DC or +/-12V DC power inputs and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
Emissions Reference Source (ERS)
Emissions
-
The ERS is a comb generator that radiates RF continuously every 2MHz over the range 30MHz - 1000MHz. Each 2MHz peak is precisely measured during the calibration process with the ERS orientated both vertically and horizontally. These measurements are correlated against a 3m OATS such that any fully implemented CISPR16 site, measuring at 3m and using height scanning, will read the same.
-
Product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
Relay
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
-
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
Carrier Board
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
Product
Ancillary Test Cell Products
-
In addition to our innovative and industry leading AccuDyne AC Dynamometers and DynoLAB Test Automation Systems, SAKOR fully integrates a complete range of ancillary products and subsystems necessary for an advanced test cell. Examples include:*Combustion air consumption measurement and conditioning subsystems*Exhaust handling systems*Fuel consumption measurement and conditioning subsystems*Coolant and oil conditioning systems*Throttle actuators*Spark/Fuel controls*Combustion analysis systems*Complete exhaust emissions analysis systems (per 40 CFR 1065 regulations)*Sound attenuating (up to STC 52) test cell enclosures with several fire suppression options*Process water evaporative cooling tower
-
Product
Solar Power Optimization
-
Accurate assessments of solar power resources at a potential site can support planning and provide information that ensures optimum solar power yield.
-
Product
Robotic Cell for Testing Car Multimedia System
-
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
-
Product
UV Solar Simulators
-
UV Solar Simulators - please contact the company directly for more information.
-
-
Product
Solar Simulation Systems
-
PET Solar Simulators consist of a Light Source with a built-in Lamp Power Supply. The Solar Simulator has an ellipsoidal reflector that surrounds the lamp and collects most of the lamp output. The radiation from the lamp is focused onto an optical integrator that helps produce a uniform diverging beam. The beam is diverted 90° by a mirror onto a collimating lens. Special filters are placed between the mirror and the collimating lens to shape the radiation spectra to match various air masses. The output is a uniform beam that closely matches the sun's radiation spectra for a given air mass. Various models offer different areas of illumination. Each model can be manufactured to simulate the sun's radiation for different air masses.
-
Product
Solar Turnkey Lines
-
Ecoprogetti offers complete solar turnkey lines for the manufacturing of photovoltaic modules. According to the customer's needs we customize the line in order to always give the best solutions.
-
Product
Solar Simulator
PEC-L15
-
●Light source/lamp house integrated compact design●Irradiation head rotates (downward, upward, sideways irradiation possible)●5cm square optical filter can be attached●Equipped with high-speed shutter (100ms)●Body weight is only 16kg.
-
Product
Standalone Terrestrial Solar Array Photovoltaic Simulator
TerraSAS (ETS Series)
-
AMETEK Programmable Power, Inc.
For microgrids, energy storage, and inverter test applications, the TerraSAS™ series photovoltaic (PV) simulators are specifically designed to emulate the dynamic electrical behavior of a terrestrial PV solar array. They offer low output capacitance and high closed loop bandwidth to keep up with the advanced Maximum Power Point Tracking (MPPT) algorithms used in today’s grid-tied inverters. The Embedded TerraSAS (ETS) is a high performance solution in a small form factor that combines an agile power supply with an innovative I-V curve generator in a single standalone unit.
-
Product
Ultra-Low Noise, Precision Voltage Reference
ISL21090
-
The ISL21090 is an ultra-low noise, high DC accuracy precision voltage reference with a wide input voltage range. The ISL21090 uses Renesas' advanced bipolar technology to achieve sub 1.0µVP-P (1.25V option) 0.1Hz to 10Hz noise with an initial voltage accuracy of 0.02% (2.5V option).
-
Product
Nonferrous Metal Reference Materials
-
NCS Testing Technology Co., Ltd.
Nonferrous Metal Standards
-
Product
Next Generation Subsea Attitude and Heading Reference Systems
TOGS
-
The new TOGS subsea navigation system is built on core TSS fibre optic gyro (FOG) navigation technology with significant improvements in efficiency and functionality. It is available in three standard heading accuracy variants: 0.1° (TOGS1), 0.3° (TOGS3) and 0.5° (TOGS5), all rated for operational depths to 4,000m or 6,000m. Attitude data is delivered via accurate roll/pitch measurement capabilities of 0.01° (TOGS1) and 0.05° (TOGS3 and TOGS5), and a heave performance of 5cm or 5%.
