Translators
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Contacting Single-turn
-
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustments. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
Product
Interface and Isolation
-
Analog Devices offers a wide range of digital interface and digital isolators with iCoupler® technology covering the industry’s field bus and peripheral communications standards. Digital isolators, isolated transceivers, isolated A/D converters and isolated gate drivers utilize the award winning iCoupler® and isoPower® technologies for isolation solutions without many of the constraints found in optocouplers. Find design solutions for interface devices including keypad controllers, level translators, and high voltage protection products (channel protection, fault protection, overvoltage protection), and latch-up proof switches and multiplexers.
-
Product
IR Thermometer
DIT-500
-
Temperature meters operating in the infrared are used to determine the temperature of the surface of the item. The optical system of the device detects the emitted, bounced and sent energy, which is collected and concentrated on the detector. Electronic system translates optical data into temperature value. In order to increase accuracy the laser pointer is built-in the device.
-
Product
97 lane, 25 port, PCI Express
PEX 9797
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Test Studio Dev Edition
-
Test Studio Dev Edition is a Visual Studio extension allowing software engineers to create functional automated UI tests in Visual Studio using C# or VB.NET. It is designed to provide ready-to-use Visual Studio automated testing functionality across web and desktop. Applications that are built with the Telerik and Kendo UI controls can be automated in a snap, by way of built-in native component translators.
-
Product
CAD / BOM Translation Software
ProntoTEST-FIXTURE
-
In minutes the Unisoft ProntoTEST-FIXTURE software translates CAD and Bill of Materials (BOM) files into real reference designators, netlists, X/Y component pin geometries, values, tolerances, part numbers, etc. This data is then used by Test Engineers to program their ATE (Agilent/Hewlett Packard "board & board x/y", Teradyne "ipl", Genrad ".ckt"), MDA, and flying probe test equipment and design the "Bed of Nails" test fixtures.
-
Product
Data Gateway
SCADA
-
The SCADA Data Gateway can be used as a data concentrator or a data translator or both at the same time. Check out the features of this advanced, yet affordable Gateway.
-
Product
Analog Ultrasonic Inspection System
ULTRAPROBE 100
-
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
Product
Radio Frequency (RF) And Microwave Products
-
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
Product
VectorPro - Simulation Cyclizer for VCD to WGL/STIL
VectorPro
-
VectorPro is a low-cost, intuitive test development tool used to translate VCD/EVCD simulations into cyclized ATE Test Vectors in either WGL or STIL formats. This highly versatile tool reads in both VCD and EVCD formatted design simulations, and through the use of its flexible GUI, users are able to view and modify the simulation to fit the needs of their Test Environment.
-
Product
Ultra-High Vacuum Ф4 Scanning Kelvin Probe
-
The Ф4 Ultra-high Vacuum Scanning Kelvin Probe system gives the user full access to work function measurements under vacuum with the ability to alter the temperature from 77 K to 860 K. The Kelvin Probe measurement has resolution of 1 - 3 meV for a 2 mm tip on a conducting sample. The sample is mounted on a plate that is located on a motorized (x, y, z) translator attached to a stainless-steel vacuum chamber. Phi 4 also comes with a photoemission spectroscopy system with a tuneable source (3.4 - 7.0 eV). The deep ultra-violet (DUV) light spot measures approximately 3 x 4 mm. Absolute work function measurements can be obtained with this system in the range of 4.0 - 6.5 eV with an accuracy of 0.05 - 0.1 eV.
-
Product
Non-Contacting Single-turn
-
A rotary position sensor translates angular positions to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for a different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
Product
Test Engineering
-
TestEdge engineers have an average of 17 years of engineering experience in test, packaging, and fixturing. This experience is across a wide spectrum of products, customers, and ATE platforms. We have experience in all of the following:Digital, analog, mixed-signal, RF Test programming servicesRemote test capability Semi-automatic test generation Automatic data collection and reduction High performance test fixturing Format independant vector translation High power testing with liquid cooling
-
Product
Precision Studio Monitor
Amie
-
Amie unleashes your creative power by extending the accurate translation of the Meyer Sound Acheron screen channel loudspeakers to smaller studio environments.
-
Product
PXI Digital Multimeters - DMM
-
All three PXI-DMMs deliver market-leading speed at their price points, measuring up to 15,000 readings/s with a maximum single-reading rate of 66 µs. These fast reading speeds translate into higher test system throughput and lower cost of test. Advanced triggering, enhanced functionality, and a full suite of free software simplify system integration and operation.
-
Product
Quadrature Digital Up Converters
QDUC
-
Analog Devices digital up/downconverters serve as the frequency translator and digital filter between data converters and DSP blocks. These innovative products enable highly programmable and configurable receive and transmit signal chains, allowing multichannel, multicarrier radio platforms in 3G wireless base stations. They also meet the digital data conversion requirements for many other communications applications.
-
Product
Weather Radar Receiver
-
This is an example of a custom four-channel C-Band Receiver uses a single conversion technique to translate incoming 5.56 GHz radar signals to a 60 MHz IF. The Receiver is divided into two polarization sections, each with a dedicated channel for the received signal and a second channel for a reference signal originatingfrom the transmitter. There are two identical circuits in the Receiver, one reserved for vertically polarized signals, and the second for horizontal signals.
-
Product
65 lane, 17 port, PCI Express
PEX 9765
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
Level Translators
-
ADI’s level translators offer the most flexible level translation solutions in the industry. The ADG3241 series translators allow direct 3.3 V to 1.8 V translation by means of the innovative SEL pin function while allowing bidirectional data transfer. The ADG3231 series allows wide range 1.65 V to 3.6 V translation and the ADG3308 series allows the industry's widest 1.2 V to 5.5 V up or down translation while permitting bidirectional data transfer.
-
Product
49 lane, 13 port, PCI Express
PEX 9749
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe.
-
Product
Camera Link Translators
CLT-303
-
The CLT-303R and CLT-303L Camera Link Translators convert RS-422 & LVDS to Camera Link, enabling the use of cameras incorporating traditional RS-422 and LVDS parallel digital interfaces with Camera Link frame grabbers. The “R” and “L” versions support RS-422 and LVDS cameras, respectively. These Camera Link converters are extremely flexible and can convert a wide range of cameras from parallel digital output to Camera Link base configuration with up-to 24-bit data.
-
Product
Distance Measuring Equipment (DME)
MS 2002
-
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
Product
Eyepiece-less Stereo Microscopes
-
Vision Engineering’s eyepiece-less stereo microscopes are better for users and for business. Their ergonomic design lets the operator sit back in a comfortable position, and the expanded pupil technology delivers an enhanced 3D view of the subject. The relaxed natural posture makes it easy and to work with tools and to manipulate the subject. Greater comfort and ease of use directly translate into greater productivity and quality.
-
Product
Protocol Converter
MACC2
-
When designing or upgrading avionics systems we are often faced with the task of integrating components that were not originally designed to work together.A control computer that communicates using RS-232 may need to control component that expects MIL-STD-1553 messages or an INS may put out ARINC-429 labels, which are needed by Multi function Display designed around RS-422.Faced with problems like these, integrators must choose between two poor options. They must either give up on one of the units in favor of another unit that may be less suitable but uses the appropriate communications spec; or they must add a computer system – often PC104 – which can translate from one unit to the other. These computers are generally large, heavy, hot, and require substantial power.
-
Product
High Speed Logic and Data Path Management
-
The ADI Data Path Management portfolio offers Data Path Signal Conditioners, Digital Crosspoint Switches, Level Translators, Serializer/Deserializer & Selector Muxes and Track/Hold Amplifiers for meeting the tight requirements of modern high data rate system. ADI's system solution focused products are easy to integrate to any signal chain with single supply usage while achieving low jitter, high output swing, fast rise/fall time.
-
Product
8 Channel NIM-ECL/ECL-NIM Translator
V538A
-
The Model V538 A is a 1-unit wide VME module housing 8 independent logic level translators. Each of the 8 channels accepts a NIM or ECL signal and provides two NIM and two ECL outputs (OUT 0÷7 A, B). The NIM and ECL inputs of each channel are ORed prior to fan-out.
-
Product
Multiphoton Laser Scanning Microscope
FVMPE-RS
-
The Olympus FVMPE-RS multiphoton imaging system is purpose-built for deep imaging in biological tissue, aimed at revealing both detail and dynamics. Innovative features for efficient delivery and detection of photons in scattering media enable high signal-to-noise ratio acquisition. This translates to bright images with precise details — even from deep within the specimen. High sensitivity is matched with high-speed imaging to capture rapid in vivo responses. For advanced applications, dual-wavelength excitation extending to 1300 nm is available. Independent control of visible or multiphoton laser light stimulation and the ability to synchronize with patch clamp data are also possible.
-
-
Product
UVM Register Generator
IDesignSpec™
-
IDesignSpec is an award winning product that helps IP/SoC design architects & engineers to create simple yet powerful specification in MS Word, Excel, Libre Office or plain text. The specification is content aware and any conflict in address is checked and highlighted in the specification itself. Any change done in the specification automatically gets translated into code.
