Brake
-
Product
Brake Testing Technology
-
Maschinenbau Haldenwang GmbH & Co. KG.
The brake test technology is mainly used to test the effectiveness of the braking system of motor vehicles. Depending on the application, roller brake testers or a deceleration measuring device are used. These are available in different versions depending on the type of vehicle and the structural situation.
-
Product
1650 HP Water Brake Chassis Dynamometer
TD-36X3
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 45 mph (1,230 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 6 fixed rolls to accommodate axle spreads from 48 to 74 in. (1,219 to 1,880 mm) tandem centers and 50 to 64 in. (1,270 to 1,626 mm) tridem centersPit Required Depth: 35 in. (889 mm)
-
Product
550 HP Water Brake Chassis Dynamometer
TD-24S
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 8,700 lb (3,946 kg)Capacity: 550 hp at 35 mph (410 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rollsPit Required Depth: 27 in. (686 mm)
-
Product
Brake Test Systems
-
Worldwide, high-speed transport is getting more important. Only through continued improvement and expansion of braking systems, will suppliers all around the world provide a solid foundation for safe traffic. HORIBA has been successfully making brake test stands for more than 90 years.
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-24
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred
-
Product
Connect Series Brake Testing Product Family
-
Maschinenbau Haldenwang GmbH & Co. KG.
MAHA Connect Series Brake Testing Product Family
-
Product
Electronic Brake Meter for Forklift Trucks
BrakeCheck FLT
-
The BrakeCheck FLT is our portable brake tester designed specifically for forklift trucks.The Bowmonk BrakeCheck FLT is a fully self-contained, user-friendly, portable brake tester, which has been developed with a leading forklift truck manufacturer to take account of the slow speed and tilt of forklift truck vehicles. The instrument records the braking efficiency and percentage of braking imbalance in a matter of minutes.
-
Product
Brake Testers
-
Orbit Controls Decelerometers are mobile measuring devices for measuring the braking behavior of road or rail vehicles as well as trailers depending on the braking force and pressure in the air or hydraulic braking system.
-
Product
Tire & Brake Examiner
-
A laser-enabled tire tread depth & brake disc wear examiner that provides users with quick and accurate wear measurements. Measure brake disc wear without having to remove tires.
-
Product
Multi-Purpose Brake Dynamometers
GIANT 6000 Series
-
The GIANT 6x00 product line is a multi-purpose, full-size inertia brake dynamometer for performance and NVH tests of brake systems from passenger vehicles to truck brakes, commercial vehicle assemblies and high-speed railway applications. The GIANT 6x00 product line offers a complete range of test functions for fully automated performance tests and basic NVH investigations and can be designed to fit the requirements of our customers.
-
Product
Water Brake Dynamometers
TD Series
-
With a versatile variety of six models, TD Series Water Brake Dynos offer are well-suited for both steady state and modest transient testing in a wide range of medium- to heavy-duty applications.
-
Product
Electronic Brake Meter Quarry & Plant Vehicles
BrakeCheck4Quarries
-
The BrakeCheck4Quarries is our portable brake tester designed specifically for quarry and plant vehicles (including mobile cranes). The Bowmonk BrakeCheck4Quarries is a fully self-contained, user-friendly, portable brake tester, suitable for quarries, coal sites, concrete plants, brickyards, recycling plants and HGV workshops. The instrument records the braking efficiency in a matter of minutes, and can optionally record the percentage of braking imbalance.
-
Product
Water Brake Engine Dynamometers
Hydraulic Dynos
-
Ideal for a wide range of markets, water brake engine dynamometers churn water inside the housing and transfers energy by momentum exchange and water shear. The more water flowing through the dyno, the greater the braking force exerted on the device under test.
-
Product
1650 HP Water Brake Chassis Dynamometer
TD-24X3
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 35 mph (1,230 kW at 56 kph)Rolls: 24 by 34 in. (610 by 864 mm) 4 front fixed rolls, 2 sets of 2 rear rolls to accommodate axle spreads from 48 to 66 in. (1,219 to 1,676 mm) tandem centers and 52 to 62 in. (1,321 to 1,575 mm) tridem centersPit Required Depth: 27 in. (686 mm)
-
Product
Digital Controller
SPARC Controller
-
SPARC Brake is a digital controller optimized for Inertia Brake Dynamometers. As a member of the SPARC family of universal controllers, SPARC Brake is using a modular design to enable more flexible configurations to fulfill any specific test environment.SPARC Brake uses sophisticated control algorithms and provides superior and intelligent control of brake actuators with highest control accuracy to cover the wide range of brake test applications. From simple static brake testing to high dynamic simulation procedures, it is able to meet the highest demands for today’s and tomorrow’s brake test requirements, for example GM-TIP.
-
Product
7 Flat (Spade) Pin Trailer Circuit Tester
PT7893
-
Easily test trailer plug circuitry on most new light trucks, SUV's and RV's. Just plug the plug tester into the trailer plug socket and activate the lights, brakes, turn signal etc.
-
Product
Metallurgy Products
-
Our market-leading electromagnetic stirring and braking solutions (EMS) deliver metallurgical improvements that are proven to increase productivity, end-product quality and reduce operating costs for electric arc, ladle and aluminium furnaces, as well as thick and thin slab and billet and bloom casters.
-
Product
Advanced Driver Assistance System (ADAS)
-
Cars have come a long way since they first came on the road in the 19th century. The first semiconductor-based noteworthy assistance was GPS-based car navigation systems toward the end of ´80s. Today, in almost every car, ABS (Anti-Lock Braking System) and ESP (Electronic Stability Program) are also contributing toward the driver and car passenger’s safety using high quality electronics. After all, the dreams of automated cars from the ´60s are now becoming true — it is only a matter of a few years.
-
Product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
-
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
Product
Super MUTT Head Portable, Remote Controlled Diagnostic Trailer Tester
#9005A
-
Innovative Products of America
The Super MUTT Head is a portable, remote controlled diagnostic trailer tester for inspecting lighting, ABS and air brake systems on commercial type trailers. Specially designed for service trucks and offsite inspections, the Super MUTT Head is powered by an (optional) internal 12v battery, or external power source such as a service truck battery, using the supplied external connector and requires shop air for air brake application.
-
Product
Technician Tools
-
Besides DG’s vehicle network engineering tools, DG Technologies also offers a variety of diagnostic pass-thru tools for technicians. DG’s hardware and software products are used by a variety of aftermarket customers such as: Mechanics, Technicians, Locksmiths and Vehicle Security Professionals. DG has diagnostic and reprogramming products for automotive vehicles, heavy-duty vehicles and everything in between; all with coverage for engine, brakes, transmission & body. Each of these pass-thru translator tools comes with their own standard diagnostic software and can be used in conjunction with most OEM software to reflash and translate the more detailed manufacturer-specific information acquired from DG’s hardware.
-
Product
2WD Dynamometers
MD-600 Series
-
The MD-600 is capable of measuring 2,000 horsepower and a top speed of 200-mph. A single eddy current PAU gives this dyne 900-hp of braking, while adding another PAU doubles this to 1,800-hp of loading capacity for steady state tuning and loaded mode testing.
-
Product
Water Brake Engine Dynamometers
DH Series
-
Ideal for gasoline engines and lower-horsepower diesel engines, Taylor Dynamometer’s DH Series Water Brake Engine Dynos can operate at speeds up to 5,500 rpm. Choose from three different models with capacities ranging from 270 to 805 hp (201 to 600 kW).
-
Product
550 HP Water Brake Chassis Dynamometer
CM-51S
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
Product
MBT 2000 Series
-
Maschinenbau Haldenwang GmbH & Co. KG.
The individual tester from the seriesincluding brake testers up to testing lanes
-
Product
Acceleration Simulation Mode (ASM) Roller Set
ASM-P-PLUS | VP 230047
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-P-PLUS roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The increased tractive force of its eddy current brake means that the ASM-P-PLUS is also suitable for power measurements at constant speed and constant tractive force.
-
Product
Heavy Duty Dynamometers
MD-7500-HD
-
Today’s Fleet Managers are faced with many challenges – most important of which is maintaining a healthy bottom line. With fuel costs at an all-time high, these challenges have become increasing difficult. Fleets being transitioned from fossil fuels to electric propulsion also face challenges with durability and range to make sure routes can be completed on time each and every day. To help combat these problems and others facing fleet managers today, Mustang Dynamometer offers the MD-7500-HD Series Chassis Dynamometer – which features the most advanced diagnostic capabilities in the industry. The MD-7500-HD is designed to simulate the driving conditions that fleet vehicles encounter on the road every day in a safe and controlled shop floor environment so that critical engine and drivetrain systems can be evaluated to insure vehicles are performing properly and at maximum efficiency. What’s more, the MD-7500-HD offers several levels of testing capabilities in a modular, compact package and with capabilities that can be upgraded in the future as your needs change. Every vehicle in your fleet can now be tested and validated before and after a repair to ensure proper diagnosis and repairs have been performed. In addition to testing repaired vehicles, the MD-7500-HD can be used to test vehicles on a regular basis as a preventative maintenance measure which decreases unexpected breakdowns and allows fleet management to control fuel costs while reducing repair costs. Periodic testing keeps fuel consumption to a minimum and helps technicians identify suspect components before they fail. A proactive approach to Fleet Service can prevent unexpected engine and or drive-train failure which saves organizations thousands of dollars in lost fair revenues. At the heart of the MD-7500-HD is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) – more than enough to simulate a fully loaded transit bus. As the systems PAU’s (brakes) are air-cooled, no water is required to or from the device – eliminating the high cost of water consumption and/or the cost of an expensive water recovery system – which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements. AC Motors can be added to simulate regeneration and validate range for organizations that have transitioned to carbon free electric propulsion. The 7500 is the best solution for fleet managers looking to improve their bottom line and offer disruption-free public transportation.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 4.0 W250 | VP 210157
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans, and with high vehicle throughput and increased loads.
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-36
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
