Active Filters
Require power to operate, using active devices and passive components in a frequency-selective network, only passing certain frequencies.
-
Product
1.5 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1500 is ideal for 1 GHz and lower oscilloscopes.
-
Product
CAT-5 Video Variable Filters
-
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
Product
5G 256-Element Active Antenna Innovator’s Kit
AWA-0134
-
The AWA-0134 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0134 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
Product
Single Channel USB Programmable High-Pass Filter
USBPHP-S1
-
The USBPHP-S1 stand alone USB controllable module provides a single channel of high pass filtering and high-quality instrumentation amplifier for front-end signal conditioning compatible with all popular A/D converter devices. The USBPHP-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPHP-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPHP-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
Product
Active Probe
Sonic
-
PMK Mess- und Kommunikationstechnik GmbH
The Sonic® 4000 active probe offers best-in-class performance and is easy to use to make in-circuit measurements. The DC to >4GHz bandwidth, high input impedance, low noise and ±8V dynamic range make the Sonic 4000 the ideal probe for use with any oscilloscope or other 50Ω measurement system. The Sonic® 4000's ±12V input offset capability extends the probe's input voltage range.
-
Product
Active Scanning Technology
-
ZEISS invented scanning in response to the drawbacks of single-point measurement nearly 50 years ago. This game-changing development enables the capture of thousands of data points within just a few seconds for truly reliable tactile quality assurance. It also saves time and money by delivering the high throughput and accurate results that are vital for manufacturing.
-
Product
Active Optical Connectors
-
Panasonic Industrial Devices Sales Company of America
All-In-One Design, Integrated Fiber Cable for High-Speed Transmission.Panasonic, a worldwide leader in Connector Products, offers the V Series Active Optical Connectors. Featuring a built-in Laser Diode and Photodiode along with an electrical/optical conversion function, the V Series is an all-in-one optical transceiver capable of transmission rates up to 8 Gbps.
-
Product
Dual Filter
Trig-TekTM 550D
-
Two channels with variable high pass and low pass filters in a module 7" high x 2.6" wide
-
Product
256-Element Active Antenna Innovator’s Kit
AWA-0142
-
The AWA-0142 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0135 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0135, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0142 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
Product
1 GHz, 1 MΩ, 0.9 pF Active Probe
ZS1000
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS1000 is ideal for 200–600 MHz oscilloscopes.
-
Product
Antenna, Active Loop
EM-6876 | 9 KHz – 30 MHz
-
The Electro-Metrics EM-6876 Active Loop Antenna is used with EMI Receivers and Spectrum Analyzers with 50 ohm input and covers the frequency range of 9 kHz to 30 MHz.
-
Product
Filtered Analog Input Expansion Board
MSXB 048
-
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
Ground EMI Filters
-
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
Product
Active Hot Parameters
S93110B
-
S93110B active hot parameters is available on PNA-X Series network analyzers (N524xB) and provides more accurate method to test hot S-parameters, gain and output power, etc. than traditional methods by utilizing X-parameter technologies.
-
Product
Active Air Speed Transmitter
HD103T.0
-
Active air speed transmitter with hotwire sensor. Probe with 5m cable. Speed 0.1…5 m/s. Outputs for temperature and airspeed.
-
Product
InfiniiMode Active Differential Probe, 3.5 GHz
N2751A
Oscilloscope Probe
The N2751A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2751A probe’s InfiniiMode provides the following modes of operation.
-
Product
Differential Active Probe, 500 MHz
DP0011A
Signal Probe
The Keysight DP0011A is the 500 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
Product
Low Frequency Active Antenna And Amplifier
Type NLF-2
-
A Hot, Active, Noise Reducing Antenna System that will sit on your desk and copy 2200, 1700, and 600 through 160 Meter Experimental and Amateur Radio Signals!
-
Product
Cell Fractionation Filter
CELLNETTA MZM1 Series
-
Cell sorters, magnetic beads, and gravity separation are common cell fractionation methods. CELLNETTA uses the micron size differences of cells to enable conventionally difficult high-precision fractionation and simple cell separation using an innovative fractionation filter.
-
Product
Active Probe, 5 Hz to 500 MHz
41800A
General Purpose Probe
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
Product
Gas Filter Correlation Carbon Dioxide Analyzer
Model T360
-
The Model T360 CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 2.56 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Particulate Filter Management System
PFS-ONE
-
The highly precise weighing of emission particles has become increasingly important due to new legislative regulations such as Euro 6, WLTP, EPA 1066 or PM 10. PFS-ONE, the Particulate Filter Management System offers different weighing methods. This supports full compliance with current legislation in the automotive and environmental industry and also allows for flexibility of internal testing processes. The system covers the measurement, organization, tracking and control of particulate filter weighing. Built as a modular system, the PFS-ONE can be expanded from a stand-alone installation up to a fully integrated laboratory module and can be used for manual weighing or automated weighing via a robot.
-
Product
High Impedance Active Probes
28 AND 29
-
Designed to serve the needs of integrated circuit engineers working in the most advanced high speed, submicron, MOS technology. These high frequency instruments include the attractive features of the Models 18C and 19 including full dc capability, negligible dc current drain, and extremely low input capacitance. In addition the frequency range of the Models 28 and 29 has been extended to a full 1 GHz.
-
Product
1 MHz Bandwidth Voltage Preamplifier with Bandpass Filter
EC6081 mk2 - preamplifier
-
The EC6081 mk2 (VP2000) is a 1MHz bandwidth voltage preamplifier with bandpass filter that is designed for uses in conjunction with piezoelectric hydrophones. VP2000 offers excellent low-noise performance over the entire frequency range; and adjustable gain selection. A range of 12 high-pass and 12 low-pass filters are available, these allow ideal band pass filter settings.
-
Product
SA1000X, 1 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe
784255-01
Oscilloscope Probe
1 GHz, ±8 V, 10X Attenuation, Single-Ended Active Oscilloscope Probe - The SA1000X is single-ended, active voltage probe that is used for many different high-speed measurement applications. The probe is powered by an included auxiliary power supply that is internationally compatible and certified. You can use it with oscilloscopes that provide 50 Ω input impedance.
-
Product
Low-PIM, High-Power Filter Solutions for Monitoring Broadband Emissions
-
Enables monitoring of PIM to 13 GHz; 100W CW and 1KW peakNear-end monitoring: Carriers rejected -90dB by the notchtravel through the bandpass filter to the low PIM termination.Far-end monitoring: Carriers rejected -90dB by the highpass,IM products passed are monitored by the spectrum analyzer.
-
Product
Diode Pumped Actively Q-switched Lasers
NL120 Series
-
NL120 series electro-optically Q-switched nanosecond Nd:YAG lasers provide up to 10 J per pulse with excellent stability. The innovative, diode‑pumped, self‑seeded master oscillator design results in Single Longitudinal Mode (SLM) output without the use of expensive narrow linewidth seed diodes and cavity‑locking electronics.
-
Product
Wide Band Filters (multi-octave)
NANO-ERF® Series
-
The NANO-POLE® Extended Range Series of tunable filters was developed to address applications needing an extremely small surface-mount package with low power consumption. Wide tuning range is accomplished with careful design to minimize size and power consumption.
