Emulator Adapters
-
Product
On-Chip Debugging Emulator
E2 Emulator
-
The new E2 emulator is an advanced on-chip debugging emulator and flash programmer developed based on a concept of "improvement of development efficiency". The download speed is up to twice as fast as the E1 emulator. Moreover, new solutions contributing to reduction in development time will be available.
-
Product
32/64b 33/66 MHz PCI-x to PMC-x Adapter
8098a
-
The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot while providing a migration path for PCI-X board suppliers to port their products to a PMC-X form factor.
-
Product
Test Adapter
-
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
Product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
-
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
-
-
Product
64-Bit PMC to PCI Adapter
4954
-
This 64-bit PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications. PMC suppliers can introduce products to desktop packaging without having to maintain two PCI-based designs ? one for standard PCI and a second for PMC.
-
Product
Flexible x1 PCI Express to MiniPCI Adapter
SKU-067-0X
-
Flexible x1 PCI Express to MiniPCI Bus Adapter (Adapter) was designed to convert PCI Express bus into standard MiniPCI bus. It allows connection of a standard 124-pin MiniPCI add-in board to a motherboard PCI Express connector.Adapter includes a MiniPCI Adapter board (downstream), x1 PCI Express host board and flat PCI Express cable.
-
Product
PCIe OCP 3.0 Ethernet Adapter
N1100G
-
Based on Broadcom’s scalable 10/25/50/100/200G Ethernet controller architecture, the NetXtreme®-E Series N1100G 1x100G OCP 3.0 adapter is designed to build highly scalable, feature-rich networking solutions in servers for enterprise and cloud-scale networking and storage applications, including high-performance computing, telco, machine learning, storage disaggregation and data analytics.
-
Product
Fiber-Optic/Copper Signal Adapters
-
Fiber-optic and copper signal adapters extend the functionality of Arbiter Systems® Timing and Frequency solutions. These products support conversions between fiber-optic and copper wire distribution networks. They may be used with Arbiter products as well as other third party devices.
-
Product
2.5-inch IDE Disk Adapter
4946
-
The HDD is positioned midway such that the PMC component envelope is not violated. Furthermore, steel rails are attached to the printed circuit board, allowing for a secure, robust installation of the hard disk drive. This is a superior mechanical approach, compared with other printed circuit board-based solutions available on the market.
-
Product
PCI Adapter for cPCI
PCI2cPCI
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
PathWave BenchVue Advanced Battery Test And Emulation Software For A Single Instrument
BV9211B
-
Achieve higher accuracy, repeatability, and safety with an emulation based on a unique battery model. Your model will allow you to determine your device's power consumption, emulate an actual battery, and import existing battery models.
-
Product
8-Port RS-422 Async Serial Communications Adapter PMC
2316
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS422 signaling levels
-
Product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Maxi Relay Adapter
190-8
-
The relay in question is a popular 50 Amp relay used on heavy duty, equipment, automotive branch circuits and other higher current applications. The Maxi relay has two large legs and two smaller legs on it,
-
Product
XMC-to-PCI Express (PCIe) Adapter
8613
-
Our Reverse Compact XMC-to-PCI Express (PCIe) Adapter 4X (8613) permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported.
-
Product
Adapters & Converters
-
Using our prebuilt, off-the-shelf standard adapters, custom converters, or custom adapters, incorporate performance and process data from across your enterprise, without having to disrupt your manufacturing line or change the outputs or your manufacturing process.
-
Product
PCB Adapter, Receiver, SIM, VTAC, 96 Pos, 14 Slot, to (1) 12x InfiniBand
510170108
-
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single 12x InfiniBand connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
Product
Calibration Hex Step Adapters
-
When performing torque wrench calibration or testing, adapters are often needed, especially with torque wrenches that have open-end heads. Mountz’s calibration hex step adapter features four common sizes, which will increase the productivity of your torque wrench calibration process. This adapter will make testing and calibration simple and efficient.
-
Product
Adapter / Carrier Converter Card
PCIBPC104pET
-
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
Product
Test Adapter
FECVF1600
-
Frothingham Electronics Corporation
The VF1600 Test Station is a high current forward pulser designed to be used in conjunction with our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of much higher forward current. The VF1600 station can produce a maximum current of 1600A at up to 5V using an 8.3 mS half sine waveform at the built in test station, and THETA and DVF tests at up to 500A at 10mS pulse width. It is derated for wider pulses. For rectangular VF pulses at 300us or 1ms, it can produce up to 2000A. The station can also test all of the usual FEC200 tests in the same test program.
-
Product
Flexible MiniPCI to PCI Express Adapter
SKU-037-XX
-
The Flexible MiniPCI to PCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a PCI Express bus. It allows you to connect a x1 PCI Express add-in board to a motherboard that has a standard 124-pin MiniPCI connector.The adapter includes a MiniPCI host board, x1 PCIe (x4 PCIe is optional) adapter board and a PCI Express flat cable.
-
Product
1x/2x/4x/8x Fibre Channel SAN Emulator
VirtualSANTM
-
VirtualSAN is a high-performance Fibre Channel SAN Emulator that replicates real world network effects such as latency and errors on user traffic in a controlled environment. The VirtualSAN emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualSAN emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
PCI-104 Adapter for PMC
PC104p2PMC
-
PC104p2PMC ( PCI-104 to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard PCI-104 slot. Suitable for PCI operation with 32 bit data and 33 or 66 MHz bus operation.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8464
-
The Technobox, Inc P/N 8464 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths.
-
Product
JTAG Emulator
Blackhawk XDS560v2
-
The Blackhawk XDS560v2 STM emulator has System Trace capability, along with USB powered and LAN interfaces.
-
Product
USB Adapters
-
DekTec's classic and iconic portable adapters for USB bus are well known tools in the industry. Some of them can be considered essential tools for every DTV engineer! DekTec is proud that it has won prestigious awards at NAB and IBC for several of its USB adapters.
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
-
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Relay Buddy Adapter Set
190-4
-
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
Product
MCB Test Option, Monitor Voltage Adapter
PTE-FCB
-
The PTE-FCB / PTE-FCD can be used to effectively reduce the sensitivity of the monitor input. The monitor input detects the relay’s operation and stops (or starts) the chronometer when testing with the PTE-100-C, PTE-50-CE, PTE-50-CET, and all LETs excluding the LET-400 (which lacks a chronometer).
