Component
Testing of individual hardware or software components or groups of related components.
-
Product
Input Characteristic Analyzer of Electronic Ballast
UI2001
-
• 4 display windows for V (600V), A (2A), W, PF/Hz • THD, 0 to 39th harmonic components • Accuracy: ± (0.4% reading + 0.1% range + 1 digit) • Data and curves printable. All the data and curves can be displayed after being connected with PC
-
Product
Sensors, Probes And Coils For Component Testing
Sensors
-
Foerster Instruments, Incorporated
We offer a comprehensive range of standard and customised sensors, probes and coils for component testing. If the wide selection of standard sensors does not optimally solve your testing task, we offer you an individual new development specially adapted to your testing task. Thanks to our many years of experience, you receive reliable sensor technology for reproducible test results.
-
Product
Transportable Gas Analyzer
CGT-7100
-
The CGT-7100 analyzer measures the concentration of gases in a continuous way, using a ratio photometric non-dispersive infrared absorption (NDIR) method. All pretreatment parts required for measurement, such as the pump, filter, and electric dehumidifier, are built-in. The analyzer can measure three components including CO, CO2, or CH4 (any two of these) and O2, and is compatible with measurement at 100 vol%. The CGT-7100 has wireless communication capability, so measurement values and charts can be displayed on PCs or smart devices. And measurement data can be exported using a USB flash drive.
-
Product
4-in-1 OSLT Calibration Kit, DC to 50 GHz, 2.4 mm (m)
CK564A
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
Cable Assembly with 2.4mm Male Connectors
Y1740A
-
The Y1740A is a flexible cable with excellent phase stability. This cable is recommended for accurate S-parameter measurements using the following Keysight vector network analyzers: Streamline Series VNA, M983xA/M980xA Series PXIe VNA, or M981xAS series PXIe Vector Component Analyzer (VCA).
-
Product
Leak & Seal Integrity Tester
-
Saicheng Leak Tester is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Socket with Bifurcated Contact Solder Tail Pins
Series 0511
-
Strip-Line Sockets with Bifurcated Contact Solder Tail Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in solder tail or wire wrap pins. Consult Data Sheet No. 12009 for wire wrap pins. Optional spacer available for mounting on .300 [7.62], .600
-
Product
Photoelectric Sensors
-
*Visible red light for simple alignment*Versions for the use in high pressure cleaning applications*LED display to check operation, switching status and function*Setting process saves time and cost during set-up*Extensive range of system components for easy and secure mounting
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
Production Connectors
-
Production Connectors for the manufacturing and testing of component assemblies. Handheld Production Connectors for assembly lines. Machine Mounted Test Connectors. Part-in-Place detection.
-
Product
X-ray Inspection Performance
MXI Quadra 7
-
Ultimate image quality and magnification, Quadra 7 reveals quality defects as small as 0.1 µm. Ideal for root cause failure analysis, wire bond integrity checking, component cracking, MEMS inspection and wafer level components including TSV and wafer bumps.
-
Product
Bioprocessing And Medical Technologies
-
Parker designs breakthrough bioprocessing technologies to aid our life sciences industry partners in developing and manufacturing pharmaceutical products and also supports patient care by supplying essential components used in medical equipment.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
Benchtop Fiber Microscope
-
BL-C series X/Y Axial Adjustment benchtop fiber microscope is used to inspect the polished surface or cleaved ends of fiber optic connectors. With a critical view of fine scratches, the BL-C series benchtop fiber optic microscope is an ideal choice for factory post-polish, component assembly, QC inspection of fiber connectors.
-
Product
Precision IV Analyzer / 8 Slot Precision Measurement Mainframe
E5270B
Mainframe
Keysight E5270B Precision IV Analyzer is the complete solution for current-voltage characterization of a wide range of materials and devices. The E5270B supports multiple SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 0.1 fA. Its modular architecture allows you to configure or upgrade SMU modules for available eight slots. The EasyEXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU's versatile measurement capabilities and GUI based characterization software makes the E5270B the best solution for characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency.
-
Product
Finite Element Analysis (FEA) Solution
Femap
-
Siemens Digital Industries Software
Femap is an advanced engineering simulation software program that creates finite element analysis models of complex engineering products and systems, and displays solution results. Femap can virtually model components, assemblies or systems and determine the behavioral response for a given operating environment.
-
Product
Process Analyzers
MARGA
-
MARGA is a fully autonomous sampling and measurement system that continuously measures the water-soluble gas and aerosol components that have a direct effect on air quality. These results can then be used to study the formation of aerosols from their precursor gases and how their concentration and composition vary with diurnal and seasonal cycles.
-
Product
Industrial Ovens
-
Industrial ovens are heated chambers used for a variety of industrial applications, including drying, curing, or baking components, parts or final products.
-
Product
High-Speed Optical Delay Line
-
The Peregrine Optical Delay Line (1-cm, 60 ps delay) and the Gyrfalcon Optical Delay Line (2-cm, 120 ps) are high-speed, high precision, voice coil motor optical delay lines. They have zero-backlash and no hysteresis. Both have similar form factors that are compatible with 30-mm cage components and 1.035” – 40 threads. Both include full digital and analog control and include a USB interface.
-
Product
PXI Programmable Power Supply
Programmable Power Supply
PXI Programmable Power Supply modules feature multiplechannels that you can combine for higher voltage or current capabilities. Some modules include isolatedchannels and an output disconnect functionality that allows isolation from the device under test(DUT) when not in use and remote sense to correct for losses in system wiring. You can use these models to simplify the task of designing automated test systems for a wide range of applicationsfrom aerospace and defense to automotive and component testby eliminating the need to mix multiple instrumentation form factors in a given test system.
-
Product
Spectroscopy Software for Software Control and Data Acquisition
-
HORIBA Scientific offers a number of choices for software control and data acquisition for all of our components and custom spectroscopy solutions.
-
Product
End-of-Line IC & MEMS Tester
igentic® 841t
-
Integrated circuit (IC) and micro electro-mechanical system (MEMS) device manufacturers need to address the challenges of today's global market including increased functionality, speed and complexity while delivering components at reduced costs. Sterner Automation's igentic® 841t automated test systems meet these demanding requirements by providing a flexible platform for comprehensive end-of-line IC and MEMS device handling, testing, grading and packaging. The resulting improvements in quality assurance and process efficiency will maximize customer satisfaction and profitability.
-
Product
Basic Contact Probes (50 Mil) F05021S050L150
1010445
-
The Basic Contact Probes (50 mil) F05021S050L150 are essential components designed for precision in various applications, particularly in electronic testing and measurement. These probes boast a pitch of 1.27mm (50 mil), making them ideal for fine placements and critical connections. Engineered to perform optimally in temperature ranges from -45°C to +80°C, these probes ensure reliability in challenging environments.
-
Product
UltraScan VIS Spectrophotometer
Spectrometer
Hunter Associates Laboratory, Inc.
The UltraScan VIS easily measures both reflected and transmitted color as well as transmission haze and meets CIE, ASTM and USP guidelines for accurate color measurement. UltraScan VIS uses diffuse/8° geometry with automated specular component inclusion/exclusion. For transmission measurement, the use of a robust CIE-conforming sphere instrument (TTRAN Total Transmission mode) effectively negates the effects of minor scattering typically found in transparent samples.
-
Product
Optical Gas Imaging Camera
FLIR GF620
-
The FLIR GF620 is the first high-resolution, handheld camera from FLIR to detect methane and other volatile organic compound (VOC) emissions. With its ground-breaking 640 x 480 resolution IR detector, inspectors can check thousands of components and safely scan for gases from greater distances. It's also the first FLIR OGI camera to offer Quantification mode (Q-Mode) for streamlined set-up of the optional QL320 gas quantification system.
-
Product
Integrated Ultrasonic Level Gauge
HR9100T
-
HighReach Measuring & Controlling System Co.,Ltd
The circuit design selects high-quality power module components from the power supply part to select high-stability and reliable devices, which can completely replace the same type of imported instruments. The patented sonic intelligent technology software can perform intelligent echo analysis the debugging and the any OTHER Special the without Steps. This Technology has Dynamic Thinking at The Functions of the Analysis and Dynamic. Sound Wave at The Patented Technology of Our Company Makes at The Accuracy of at The Instrument Greatly Improved, at The Precision Liquid Level Reaches 0.25%, and IT CAN Resist various kinds of interference waves. This instrument is a kind of non-contact instrument, which does not directly contact with liquid., the instrument has a variety of installation methods. The user can use this manual to calibrate the instrument. All input and output lines Of the instrument have lightning protection and short circuit protection.
-
Product
Mass Air Flow Sensors
-
Mass air flow sensors are one of the essential components of an electronic fuel injection systems. They measure the amount of air entering the engine, or the air flow. Our reliable and accurate mass air flow (MAF) sensors help detect the mass of air flow in a variety of automotive, medical and industrial gas applications.
-
Product
Plugbord
3662-2
-
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
Product
Electromagnetic
Promis 10
-
The Promis device is a multi-frequency, multi-spacing 3 component slingram type EM System for sounding and profiling the soil. This system features a transmitter loop to produce a primary magnetic field that will induce eddy current in conductive materials. These eddy currents will generate a secondary magnetic field that will be measured with the receiver loop. This system measures the in-phase and the out-of-phase components of the secondary magnetic field.
-
Product
SMA Rotary Attenuator
WATT-6SR1101
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
