Cages
-
product
Die-cast Rotor Tester
AIP868X series
Qingdao AIP Intelligent Instruments Co., Ltd
Introducing the international testing technology and developing special sensor according to digital signal processing method, the die-cast rotor tester able to automatically analyze and judge the filling quality of die-cast rotor.This system is applied to all kinds of cast aluminum and copper rotors, such as: cast aluminum rotor of compressor motor, cast aluminum rotor of washing machine motor, cast aluminum rotor of fan motor, cast aluminum rotor of pump motor, rotor of automobile motor and three-phase asynchronous motor, etc. The main detection functions are: broken bar, fullness of the bar (thin bar, hole, bubble and porosity ), leakage between the squirrel cage and lamination, squirrel cage eccentricity, slot deviation.Test items: broken bar, thin bar, maximum amplitude value, minimum amplitude value, comprehensive value.
-
product
Single Truck Steri-Dry™ Sterilizer
The Gruenberg Steri-Dry™ Dry Heat Lab Animal Science Sterilizer provides the lab animal science market with equipment to sterilize habitat cages through the process of dry heat sterilization. These sterilizers are designed and built for lab animal science applications.
-
product
VME Test Extender 3U/220mm Universal
110EXT3122-10xx
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
VME Test Extender 3U/220mm J1
111EXT3122-11XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Analog Output Industry Pack Module, 12-bit D/A
IP220A
The IP220A outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
product
Picoamp Booster and Faraday Cage
CHI200(B)
With the CHI200(B) Picoamp Booster and Faraday Cage, current down to a few picoamperes can be readily measured. The CHI200 is compatible with the Model 600/A, 700/A series of instruments, while the CHI200B is compatible with Model 600B/C and 700B/C series. When used with 700/A/B/C series bipotentiostat, the Picoamp Booster will affect the primary channel only.
-
product
Fiber Optic Connectors & Cages
Pulse Electronics Networking BU supplies high-quality fiber optic connectors and cages to innovative ODMs, OEMs and other manufacturers designing today’s most demanding network products. Our line of 40+ fiber optic connectors include SFP, SFP+, and QSFP connector and cage products.
-
product
Freestanding Modular Faraday Cage
Holland Shielding Systems B.V.
A freestanding (independent of the host building) prefabricated modular Faraday cage provides a superior screening of RF-signals and is applicable in a wide range of situations for a wide range of purposes as described below.
-
product
Airlock Control System
The system is built on the basis of a panel computer with a touch screen, performing the functions of a user interface and recording the measured parameters. The stand is equipped with gate drives and a set of sensors (pressure, flow rate, force). Real-time gate control is implemented on the basis of the R-series board; for input and conversion of analog signals from the sensors, an expansion cage of the cRIO-9151 R-series boards is used.
-
product
Crowbar Resistors
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
product
Reduced Voltage Motor Starting Panels by Auto-Transformers
Reduced Voltage Motor Starting Panels are designed for starting of squirrel cage induction and synchronous motors. A RVMS Panel reduces the torque by temporarily reducing the voltage and/or current input. It reduces voltage applied to the motor during start up causing lower starting currents from the connected grid.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
Multi-Truck Steri-Dry™ Sterilizer
The Gruenberg Steri-Dry™ Dry Heat Lab Animal Science Sterilizer provides the lab animal science market with equipment to sterilize habitat cages through the process of dry heat sterilization. Gruenberg dry heat sterilizers are designed for lab animal science applications.
-
product
Small Form Factor (SFF)
The modular design of the Mini ATR platform allows for various configurations. The chassis can easily be scaled up or down while using the same side walls. DC and AC power variations as well as custom front I/O configurations are available. Elma also offers a wide selection of backplanes in various architectures and has different milled card cage sizes off-the-shelf.
-
product
68-Pin SCSI Micro-D Male Connector Block
40-965-068-M
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
37-Pin D-Type Connector Block
92-965-037-M
This connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
product
96-Pin Micro-D Connector Block, Male With Backshell
40-965-096-M
This connector block provides a simple method of connecting to 96-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
VME Test Extender 9U/220mm Universal
110EXT9122-0000
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Type 39 CompacFrame Development Platform, 1 - 4 Slot 3U VPX Power And Ground Backplane
39P01BWX6ZY2VCC0-Tx
Elma’s slimline CompacFrame is the next-generation platform designed to accelerate development and test of Plug-In Cards (PICs). The 3U card cage in the platform is tilted upward by 5º for easier card access and accommodates backplanes up to 4 slots.
-
product
VME Test Extender 6U/400mm J1/J2
111EXT6140-012X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
5 Slot VME64 Portable Tower Development Platform
32V05MMX36N3VCC0
Elma Type 32V with superior cooling and accepts 6U cards mounted vertically with or without rear I/O card cage, VITA & IEEE standards, heights are 63HP and 84HP (HP=.2”) and widths 3U, 4U and 6U.
-
product
25-Pin D-Type Male Connector Block
40-965-025-M
This connector block provides a simple method of connecting to 25-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties. Connector blocks have higher losses than a cable connection and the breakdown voltage is controlled by clearances to the metal shell. The metal shell includes an internal insulation barrier under the carrier board.
-
product
160-Pin DIN41612 Connector Block, Female
92-965-160-F
This connector block provides a simple method of connecting to high density DIN41612 connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
VITA, Type 32V, Portable Tower Family
32V-VITA
Elma Type 32V family of enclosures provide a lightweight, tower platform for packaging portable system applications. Designed to meet VITA & IEEE specifications. Systems can be configured with or without rear I/O card cage.
-
product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-F
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
product
68-Pin SCSI Micro-D Female Connector Block
92-965-068-F
This connector block provides a simple method of connecting to 68-Pin SCSI Style Micro-D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage.
-
product
VME Test Extender 6U/220mm 64X w/o P0
116EXT6122-012XR
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Fibre Channel Modules
AIM’s Fibre Channel test, simulation and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with one dual core RISC processor per port, massive and scalable DDR3 memory and IRIG-B time encoder/decoder functions are standard. The new ultra high performance intelligent 4-lane PCIe 2.0 interface modules offer 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The dual core processor provides onboard processing and data transfer capabilities for the most demanding Fibre Channel applications including upper layer protocol support done on board level. Large and high data throughput DDR3 RAM is accessible for the onboard processor as is a high performance FPGA implementing the customized Fibre Channel interfaces enabling the board to analyze incoming and modify outgoing data in real time. Each module provides 2 Fibre Channel compliant full duplex ports, implementing the full link level services. SFP cages make it suitable for different media types as optical or electrical network technologies. Ports operate either in Traffic Simulator or Analyzer/Monitor mode with support for port related Frame Statistics. Sophisticated packet capturing mechanism and monitoring features are complimented with powerful triggering and filtering capabilities.
-
product
Type 12R2, 8U, 19" Rackmount, MIL-Rugged, Vertical
12R2-8U-V
The 8U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
product
Type 12R2, 14U, 19" Rackmount, MIL-Rugged, Vertical
12R2-14U-V
The 14U, 12R2 was designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs.Shock isolated versions are designed to attenuate 25G shock to the chassis to less than 10Gs at the card cage and PSU tray.
