Collectors
-
Product
Differential Temperature Controller
-
Normal temperature controller acts on one single input and tries and maintain that temperature at a pre programmed constant level. A differential temperature controller as the name suggest, takes two temperature inputs and tries to maintain the difference between these two temperatures as constant. This is widely used in today’s innovation Solar Energy Systems to provide maximum operating efficiency and flexibility. It automatically maintains the difference e.g., In case of self powered solar box furnace or in case of a solar water collector. By automatically switching on a fan or a pump the temperatures can be equalized.
-
Product
DCDC
JA/JP Series
-
The 15-Watt JA/JP series operates over an ultra wide range of 9-36 Vdc or 20-72 Vdc. Efficiencies of 80% are typical over varying load conditions of 25% to 100%. Additional features include input reverse polarity protection, remote on/off control, logic compatible with CMOS or open collector TTL, short circuit protection with auto restart, overvoltage protection, and an operating temperature range of -25°C to +71°C with no derating. Units are packaged in a six-sided continuous shielded case for EMI/RFI protection and measure 2.0” x 2.0” x 0.40”.
-
Product
PXI H. Density Digital I/O Module 32 Bit O/C
40-410-002
Digital I/O Module
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface. Two choices of output drive are available: TTL for interacting with external logic and Open Collector Transistor for operating external devices with voltages to 50VDC and currents to 500mA.
-
Product
Triaxial Wireless Accelerometer
-
Our Triaxial Wireless Accelerometer is a vibration sensor specially designed for vibration analysis with universal compatibility. WiSER 3x is a wifi accelerometer that sends 3 axis vibration data + 1 additional channel simultaneously to any data collector in the market. Also, WiSER 3x is a wireless ultra-low noise accelerometer with 15 kHz bandwidth that exceeds the characteristics above all of most conventional accelerometers.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Portable Ultrasound Instrument
SDT270
-
The SDT270 Platform gives customization with the opportunity to upgrade as your program grows. Choose from six base formats, then add sensors and software to build a collector unique to your needs. SDT270 is even more powerful with UAS software . UAS forms a synergistic partnership between your SDT270, your PC, and your PdM team.
-
Product
Wireless Data Logging System
MicroLogPLUS
-
A wireless data logging system for remote monitoring of up to 200 data loggers via the cradle technology and transmitting all real-time measurements to the PC. Handles data from up to 200 MicroLogs at up to a distance of 300m (120m US Version). Two open collector output for controlling other devices set at low and high alarm levels
-
Product
Handheld Analyzers
CoCo-80X/90X
-
The CoCo-80X is a handheld data recorder, dynamic signal analyzer, and vibration data collector. It is ideal for a wide range of industries including machine condition monitoring, automotive, aviation, aerospace, electronics, and military.
-
Product
Incremental Photoencoders
-
Citizen Chiba Precision Co., Ltd.
*Ultra-small and ultralight weight*High resolution*Open collector output*Best suited for high accuracy positioning applications
-
Product
Vibration Meters
-
Is a multi-function portable meter that bridges the gap between the basic Vibration Meter and advanced FFT data collector / analyser.
-
Product
16 Thermocouples/RTD Ch
APCI-3200-16
-
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel16 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 8 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
Product
Carbon Strips Quality Tester
MR12SPX
-
The MR12SPX and its measuring probe are used for inspection and quality control of carbon strips of current collectors used by electrical powered trains, electric trams, trolley buses and similar vehicles. Here the current collectors are preferably roof mounted. Due to the often pairwise mounting of the carbon strips, there is little space between the lowered collectors. Therefore the measuring probe itself is very small. The design can be modified for your needs.
-
Product
PoKeys I/O devices
-
This board allows expanding the number of outputs of the Pokeys by using the PoExtBus. This board incorporates 16 high current/voltage open collector outputs which suits applications such as lamps, relays.
-
Product
IP Parallel HV
-
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
Product
Modules - Modules, IGBT
-
Vishay's IGBT modules are available with several different configurations, including half-bridge, full-bridge, chopper, and 6PAK inverter. A wide collector current range, up to 200 A, is available.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
20kV 4 Collector Test Set
-
Polarity designs and manufactures the most reliable Microwave Tube Test Sets in the industry. Polarity understands the delicate structure of microwave tube devices and has built an extensive product line supporting the manufacturing process.
-
Product
Metering Terminals
-
Shenzhen Star Instrument Co., Ltd.
Concentrator comes with replaceable modules. It uplinks the master station via GPRS/3G/$G or Ethernet and downlinks the energy meter or collector using the PLC/G3 or PLC/RF module.
-
Product
Route Based Vibration Data Collector
-
The Crystal Instruments CoCo series are portable devices for vibration monitoring and predictive maintenance applications. The system consists of a CoCo analyzer and the Engineering Data Management (EDM) software. The CoCo is used to make field measurements and the EDM software in Vibration Data Collector (VDC) Mode is used to setup the CoCo hardware and define routes before field measurements, and to download data from the CoCo to analyze and archive afterwards.
-
Product
2-Axis Automation
ASX-6300 Series
-
The ASX-6300 series fraction collector gathers up to eight fractions from a digester or other source. Waste is minimized by returning unused material to the source. It is designed to be sturdy, reliable, and easy to use. The fraction collector is typically interfaced to and controlled by the same computer which controls the rest of the system.
-
Product
4 Thermocouples/RTD Ch
APCI-3200-4
-
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel4 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 2 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
Product
Fraction Collectors
Foxy Series
-
Durability and reliability are built into all three of Teledyne LABS fraction collectors, the Foxy® R1, R2 and R2 High Flow. Designed for accuracy and speed, these fraction collectors represent state-of-the-art functionality and innovation. The Foxy R1 and R2 fraction collectors are liquid distribution instruments with the ability to divide the liquid into multiple collection vessels, switching vessels on time, drops, volume, peaks, or a combination of these parameters. Collection vessels can be test tubes, vials, mini-wells, bottles, or funnels. The touch screen display simplifies set-up for a variety of collection routines.
-
Product
Tracker
-
For regions with stable weather conditions, PSE provides two outdoor bi-axial trackers, which keep test samples perpendicular to the sun. PSE trackers are designed for outdoor testing and certification of both solar thermal collectors and PV modules. With our trackers it is possible to test more than one collector at the same time. Simultaneous collector testing can allow direct comparison of different collector designs under identical conditions or increase the measurement throughput of collectors and modules. In our product line we offer the following tracking systems:
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Industrial IoT Edge Gateway
-
Advantech IoT Edge Gateways help bridge data from edge devices to cloud, acting as protocol converters, data collectors, or data loggers.
-
Product
Doorbell And Telephone Detector
ELK-930
-
he ELK-930 performs three functions. It can detect ring activation from one or two doorbell buttons and a single telephone line. It conveniently isolates the voltage and current and produces an open collector (pull to ground) output which can be used to trigger an automation controller, relay, timer, etc.
-
Product
Steady State Solar Simulator
-
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
Product
Split type Pulse Current Sensor
CTF-05M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Pulse current detection for power demand meter.*Through hole type CT.*Open collector output.
-
Product
High Collector To Emitter Voltage
-
High collector-to-emitter voltage photocouplers (optocouplers) are optically coupled isolators containing a GaAs infrared light emitting diode and an NPN silicon Darlington connected phototransistor. The isolation voltage during input and output and the voltage between the collector and the emitter of the transistor are both high.
