-
Product
FaithTech Ultra Low Voltage And High Current DC Load
NZ/N Series
-
Shenzhen FaithTech Technology Co., Ltd.
Ultra low voltage and high current DC electronic load is a high reliability and high performance electronic load product derived from FT conventional electronic load for low voltage and high current test scenarios such as fuel cell test and CPU power supply device test. For different current levels, this product includes two series: NZ and N. The voltage is 0-20V or 40V, in which the NZ series can be loaded with 0V full current, and the N series can be loaded with ultra-low voltage and full current. The load capacity is up to 0V@1200A and 0.2V@5000A . This series of products has high precision and high cost performance, which is your good choice for testing.
-
Product
3CT Method Clamp Tester
MCL-4000F
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*3CT method enabled easy AC leakage current measurements with simple clamping of each phase conductor by 3 CTs or 4 CTs.*Use 4 CTs for 3phase/4wire power system.*Load current measurements for each phase conductor up to AC 800A.*Filter rejection for high frequency noise.*DC mV output for recorder.
-
Product
STM32 Arm Cortex MPUs
-
As Industrial, Consumer, Smart Home, Health and Wellness systems are growing more connected, certain embedded designs are now required to manage high processing loads and complex applications with rich Human Machine Interfaces (HMI). Under these conditions, the ability to harness open-source software stacks while maintaining low power and real-time performance are key requirements.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UTT 306 x 248 mm
MG-02-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 4 interface blocks of 160 signals• All interface blocks can be customized
-
Product
Load Shedding System
-
An advanced smart load preservation solution must dynamically determine the optimal system response to a variety of system changes and disturbances. Utilizing model-driven foundation with embedded predictive analytics, and optimization algorithms, ETAP's adaptive Intelligent Load Shedding (ILS) solution makes Faster than Real-Time decisions.
-
Product
Circuit Tester "Light and Sound" Hook Probe
TE6-0708C
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Tests 6/12 volt circuits with POWER ON.*Interchangeable tips allow tool to be used as a probe- or pierce-type tester.*Retains wire for perfect pierce with one hand.*Hook grabs hard-to-reach wires.*Durable insulated clip and heavy-duty cord for professional use.*Spring loaded strain relief prevents cord pull out and damage.*High intensity glow for under hood and under dash visibility.*Easy-to-hear buzzer provides quick circuit test confirmation.
-
Product
Resistance Measurement
PROMET
-
High-precision micro-ohm measuring systems with adjustable DC test current for determining resistances on circuit breakers or inductive loads such as transformers, for example. The high-precision ohm meters of the PROMET series are used to determine very low electrical resistances in the µΩ range. The adjustable test current of up to 600 A in combination with a four-wire measuring method delivers measurement results which meet stringent accuracy requirements. State-of-the-art power electronics coupled with a robust design guarantee excellent reliability for use as a portable device in switching stations and industrial environments. Typical applications include determining the contact resistance of switchgear devices and determining the resistance on inductive loads such as transformers.
-
Product
Power Supplies
-
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load.
-
Product
50 KN Capstan Grips For Rope
-
These 50 kN (11,000 lbf) capstan grips are designed specifically for testing the tensile properties of rope with a diameter between 8 and 28 mm (0.31 and 1.1 in). The upper and lower grips incorporate an easy-to-load split drum and the upper grip has a counterweight attached to maintain alignment of the grips with the axis of the universal tester during testing.
-
Product
Telemetry Handheld Display
TW-3.0-T
-
The TW-3.0-T Telemetry Handheld Display is a modern, slimline, multifunctional load monitoring device which is unique to DLM.This innovative design is built with the user in mind. It has a large, high quality LCD screen which is optically bonded removing the need for a back light and improving clarity in bright sunlight. There are 12 devices on the network which can each be given a customisable friendly name made visible on the screen to make instant identification possible.
-
Product
Partial Load Failure
PLF Device
-
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Quad Core KeyStone™ DSP + UltraScale™ FPGA Module
SMT6657-KU35
-
Sundance Multiprocessor Technology Ltd.
The SMT6657 DSP+FPGA module is a reliable and flexible platform for digital signal processing applications requiring high-performance integer and floating-point computation.It is applicable to both symmetric multiprocessing applications in which the computational load is shared by the two DSPs and asymmetric applications where one of the DSPs is responsible for hard real-time processing and the other acts as a supervisor, handling all non-deterministic communication and optionally running under control of an operating system.
-
Product
230V / 36 Amp Load
EL08-230M
-
For High Voltage UPS Battery Testing and Power Supply testing. This particular Load has been designed to operate with UPS Battery Systems and Telecom Rectifiers and Power Supplies with output Voltages in the range of 153V to 230V and is extremely cost effective.
-
Product
2 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 2 Ports
GPS202
-
INSTOCK Wireless Components, Inc
PS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Time Domain Reflectometer
ETDR 10A-2
-
Compact dual channel precision full function portable easy to useTDR for fault location on balanced loaded and unloaded cables.
-
Product
Low-Barrier Schottky Diode Detector, 10 MHz to 12.4 GHz
423B
-
The Keysight 423B Low-Barrier Schottky Diode detector has been widely used for many years in a variety of applications including leveling and power sensing. It offers good performance and ruggedness. Matched pairs (Option 001) offer very good detector tracking. A video load (Option 002) extends the square-law region to at least 0.1 mW (-10 dBm).
-
Product
Fatigue Rated Low Profile Cells
-
Fatigue rated load cells are specifically designed for component durability and fatigue test machines where highly cyclical loading is present. These rugged load cells are extremely resistant to extraneous bending and side loading forces. They are used for material testing, component life cycle testing and structural testing. All fatigue rated load cells are guaranteed against fatigue failure for 100 million fully reversed cycles.
-
Product
Universal Relay Driver Control - PXIe, 32 Channel Direct Relay Drivers
33011
Relay Driver
PXI-e based universal relay control for semiconductor load boards, 32CH direct relay drivers, 2 lanes of SPI relay control interface
-
Product
Waveguide Loads
-
Smiths Interconnect offeres high power Waveguide loads that can with stand up 200Watts at 18 GHz
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
PoE LLDP Emulation (PD) & Analysis for 802.3at & 802.3bt
802.3at and 802.3bt PD Emulation and Protocol Analysis
-
Integrated PoE LLDP and Load Emulation in a Single Instrument. IEEE 802.3at and 802.3bt LLDP Compliance Analysis. Independent, Per-Port 802.3at and 802.3bt LLDP Emulations. Flexible Single and Dual Signature PD LLDP Emulations. One-Click LLDP Protocol Capture and Analysis. Pop-Up Excel Spreadsheet Reports Assess Protocol Content and Timing. Enables One-Click Emulated Power-Ups and Standard Waveforms with LLDP Power Granting PSE's. Enables 2-Pair and 4-Pair PSE Conformance Test Suties with LLDP Capable PSE's. Enables 2-Pair Multi-Port Suite with LLDP Capable PSE's. Available for PSA-3000 and PSL-3000 Platforms.
-
Product
Archival Storage Rooms
-
Darwin Chambers Company’s NFPA, GSA, and NARA Directive 1571-compliant Archival Storage Chambers are engineered to provide maximum value, efficiency and conformance with all applicable standards and codes. Archival chambers provide environmental controls for storing records and materials (including paper documents and items with high fibrous content, various films, microfiche, and photographic materials) that require permanent protection for storage and preservation. Our high-performance systems are offered with nearly unlimited operational fail safes, includ- ing full system and control redundancy. In addition to keyed entry, numerous security options are also available, due to the often irreplaceable nature of the materials to be stored and preserved in this type of chamber. Our chambers are engineered to accommodate the loads and unique requirements of the specific materials to be stored, with industry-leading control and uniformity of both temperature and humidity variables. Design considerations include both functional and operational efficiencies and reliability, the safety and comfort of operating personnel, and the ongoing protection of the archived materials from fire, water, light degradation, pests, mold and natural contaminants, pollutants and other man- made threats.
-
Product
Power Monitor, AC- or DC-Powered
109
Power Monitor
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
Product
Power Supply System
PL516
-
The PL516 is a high sophisticated, high density, programmable 16-channel with full redundancy low-voltage power supply system. Using the remote monitoring and control features it can be used to supply a large numbers of external load- channels with high power consumption also over long distances.
-
Product
Load Banks
-
Power Test Dynamometer offers a complete high capacity load testing solution with our load bank and gen set testing systems. Capable of testing generators and AC/DC power sources, our load bank systems safely apply electrical loads across the entire spectrum of operation. By offering a one-stop-shop for your Load Bank and it's accompanying data acquisition software, Power Test is committed to Making Your Testing Easy.
-
Product
Thermal Cycling and Humidity-Freeze Test
-
King Design Industrial Co., Ltd.
*10.4" TFT LCD, touch-type Chinese/English display controller.*Temperature/humidity setting procedure, LCD curve display device (set to “curve display”).*Chinese/English/LCD operation/troubleshoot/guiding window.*State-of-the-art intelligent auto-dispatch “heat load value” coolant servo valve flowrate algorithm control.
-
Product
Development Test Stands for Electric Motors
-
Development test stands from imc are characterized by high flexibility in electric motor trials. A comprehensive variety of motor types can be tested and a complete range of tests carried out. The mechanical configuration consists of a test bed with a load machine and a torque measuring shaft. The load machine and torque sensor shaft are mounted on a linear guide and precisely aligned axially by means of laser. It can be moved towards the test object on ball bearings, as a complete unit. Especially time-saving: no need to realign the load machine assembly when changing the torque sensor.
-
Product
Arbitrary Load Control For Modulation Distortion
S94570B
-
Extend the modulation distortion application by computing figure of merits such as EVM and ACPR for any desired load with arbitrary load control (ALC). Modulation distortion with ALC integrates the powerful capabilities of the PNA-X with an electromechanical tuner so a non-50 Ω load can be presented to the DUT and changes in device performance or sensitivity to varying load conditions can be accurately measured.
