Locators
are used to find or position.
-
Product
25-Watt Transmitter
Loc3 25W
-
The powerful 25-watt transmitter is the go-to transmitter for cable fault locating, finding holidays on coated pipes, problematic deep-buried lines, and long-distance pipe and cable locating. The Loc3-25Tx is also well suited for applications for cathodic protected longline pipelines and gas distribution in city areas needing a low-frequency high output transmitter.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
LAN Cable Tester
PA-01D
-
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
Product
Pipe & Cable Locators
-
Schonstedt Pipe & Cable Locators have been setting the standard for reliability and dependability in locating buried utilities – water pipes, sewer pipes, cable, electrical lines, and gas —quickly and easily.
-
Product
SparkFun Triple Axis Accelerometer Breakout
LIS3DH
-
The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF, or 3 Degrees of Freedom. Inertial Measurement Units (or IMUs) can provide additional space location data, such as gyroscopic or magnetometric. The LIS3DH provided on this breakout operates under the same principles but gives a few analog inputs to play with, and it has some built-in movement detection abilities.
-
Product
Flow Monitor
B2900
-
Blancett B2900 flow monitor offers advanced digital signal processing technology in an easy-to-access package. Enclosed in a spacious polycarbonate NEMA 4X housing, the electronics are located on a single board, designed for straightforward and convenient field installation. The B2900 enclosure features an LCD display with push button programming as well as a pre-drilled hole for external wiring connections, such as Modbus RTU and other outputs.
-
-
Product
Thermal Imaging Camera
-
Zhejiang ULIRvisionTechnology Co., LTD
A thermal imaging camera is a device that uses infrared and thermal imaging technology to convert the image of the temperature distribution of the target object into a visible image through detecting the infrared radiation of the target object and applying signal processing and photoelectric conversion. The thermal imaging camera accurately quantifies the actual detected heat and images of the entire object in real-time in the form of a surface, thus accurately identifying the suspected fault area that is heating. The operator initially judges the fever condition and the fault location through the image color and hotspot tracking display function displayed on the screen of the thermal imaging detector, and strictly analyzes it, thereby embodying high efficiency and high accuracy in confirming the problem.
-
Product
Cable & Antenna Analyzer
iVA Series
-
VSWR, Return Loss Measurement & Distance to Fault. The iVA Series Cable & Antenna Analyzer is an exciting new product from Kaelus that enables users to accurately measure VSWR/return loss and the location of the VSWR/return loss faults in their RF infrastructure. The wireless connectivity allows unprecedented measurement flexibility and opens up new & important possibilities in sweep testing and multi-port testing.
-
Product
Satellite Based File Transfer
SatDrive™
-
Copy files from one computer to another via satellite. Rugged and easy to use. The SatDrive is a great solution for sending files from remote locations.
-
Product
Fault Locator
WEEZAP
-
WEEZAP is an LV vacuum circuit breaker combined with advanced measurement and protection capability.
-
Product
Bluetooth® Enabled Dissolved Oxygen (DO) & Temperature Pen
UltrapenX2™ PTBT5
-
*Industry Leading Accuracy*Display DO in Concentration, % Saturation, or Both*Adjustable for Altitude and Salinity*3 Calibration Methods: Air, Water and 0 ppm DO*Dynamic Membrane Temperature Correction*Measurement Storage with Time, Date and Location*Export Stored Measurement Data Via Email*Live or Hold Mode – User Selectable*Proprietary Sensor Design*Rugged Design with Aircraft Aluminum Body*Durable, Epoxy Encapsulated ElectronicsWaterproofPowered by One N Type Battery (Included)
-
Product
Audio Circuit Tester
25500
-
Handy device for locating short and open circuits. Horn sounds when circuit is complete. Long 5 foot leads permit technicians to work around corners, under dash boards and in trunks. For use on all 6 and 12 volt circuits.
-
Product
Audio Frequency Generator
TM530
-
TM530 Audio Frequency Generator is provided with Pinpoint Fault Locator for pinpointing the low resistance fault and detecting cable route. When detecting, TM530 will inject a signal current of 1kHz audio frequency into the cable, and accordingly a magnetic wave of the corresponding frequency will be generated on the cable. Pinpoint Fault Locator will collect this magnetic signal, thus obtains the information of the cable fault and the route.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Health Physics Systems
-
Detection and quantification of radioactive material within the body is a key factor in determining internal personnel contamination and dose assessment. These measurements can be made on body fluid samples using lab instrumentation or through direct measurement of personnel. The measurement of body fluids is generally less attractive due to the bio-hazards and lack of immediate results unless non-gamma emitting nuclide measurements are required. The direct measurement of personnel for gamma emitting radioactive material provides rapid results, can determine where the material may be located within the body, and does not require mobility of the material through body fluids for detection.
-
Product
Polarity Tester
PT-1
-
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
Product
Cable Test Van
Titron
-
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
Product
Time Domain Reflectometer
IRG 4000
-
Cable fault location with the BAUR IRG 4000. The IRG 4000 time domain reflectometer is integrated in BAUR cable fault location systems and is used in combination with the system software for locating cable faults in single and three-phase cable systems. Thanks to the novel operational concept, cable faults can be located more rapidly and easily with IRG 4000. The high-performance industrial PC and improved measurement parameters allow for a precise cable fault location in all cable types. The well-proven and continuously enhanced methods are available for the cable fault location as well as the newly developed Conditioning SIM/MIM** method which makes it even more effective and quick to locate wet cable faults that are difficult to detect. The SIM/MIM technology with 20 reflection measurements per HV pulse allows for selecting the best reflection image for a very precise determination of the fault distance.* Easy operation thanks to intuitive operational concept*Maximum precision with high resolution and sampling rate*Precise fault location methods for every type of fault
-
Product
Angular Interferometer
10770A
-
The Keysight 10770A Angular Interferometer is a high accuracy plane mirror interferometer ideal for use in precision calibration applications. Used with the 10771A Angular Reflector in an 5530 Laser Calibration System, the interferometer measures pitch and yaw motions along each axis that a machine tool or measuring machine travels. The system can help quickly locate and evaluate unwanted angular motion.
-
Product
Portable Spectrum Analyzer
-
Help you to easily scan, classify and locate signals of interest in the field environment.
-
Product
Marine
-
It’s all about location, location, location. With Trimble marine construction systems, you’ll never have to worry about yours. Trimble offers flexible, high-performance positioning systems to meet the unique needs of marine construction on both simple and complex projects. Our solutions include both hardware and software, and can be easily integrated into third-party systems.
-
Product
Other Material Analyzers
-
GAOTek portable material analyzers deliver instant, relevant data for quick decision making in critical situations. Combining advanced technologies with an incredibly easy-to-use interface, our portable analyzers provide rapid, reliable chemical identification and material verification to increase throughput, increase quality and reduce risk. It can be used in any location, field environment or weather condition.
-
Product
Cable Tester
-
The MapMaster™ mini detects faults and locations of RJ45 network cables. Good terminations, causes of faults and locations of cables are displayed on an LCD display. A set of five mapping remotes is included for locating cables terminated in wall jacks or patch panels. A built-in tone generator with 4 different tone combinations can be used with a tone probe to detect where a cable is routed and the location of the end of the cable.
-
Product
Service
-
With facilities located in the U.S., France, and China, we offer exceptional global services and support for every machine shipped. DWFritz owns your problem from concept to delivery, through installation and service, using a collaborative and consultative approach to provide design for manufacturability feedback and deliver optimal solutions.
-
Product
Digital E-Gun Sweep
XYC-20
-
The XYC-20 E-beam evaporation controller is in a class by itself. The unit can be calibrated by the user to their specific system and e-gun. An algorithm determines the beam error from front to back and side to side within the pocket, eliminating pocket overshoot and burn-thru. The pattern control is effectively made linear saving time in programming and setup. Beam dwell time can vary at each location to compensate for variation in beam density. Six pocket sizes and two shapes can be selected.
-
Product
Critical Process ESD Monitor
Novx Series 7000
-
Simco-Ion's Novx Series 7000 Process Monitor is a multi-purpose microprocessor based instrument for monitoring critical electrostatic related parameters in work station and process environments. The six dedicated use channels provide the flexibility to customize the instrument for the monitoring capability and communication required at each location.
-
Product
Visual Fault Locator
FFL-310-U
-
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
Product
Cable and Pipe Locating Equipment
-
The most advanced locating kit combining the functions of three devices: cable locator, water leak detector, non-metal pipe locator.
-
Product
Printed Circuit Board
RISER-PPM-1
Printed Circuit Board
WINSYSTEMS’ RISER-PPM-1 boards are designed to provide extra space in a PC/104-Plusstack. They are printed circuit boards (PCBs) with PCI-104 mounting holes and bus connectors. They allow a board with either tall components or heat sinks to be placed in a stack of boards in a location other than only at the top. The additional separation is 0.60 inches using standard PC/104-type spacers.
