Regulators
-
Product
Mass Spectrometry
-
Mass spectrometry isn’t just for academics and R&D labs anymore. Analytical testing labs across, food, cannabis, environmental and industrial testing face stricter, evolving regulations that demand lower detection limits and have high throughput requirements. We have the technologies, capabilities and services to address these challenges – with ease and reliability.
-
Product
Insulation & Multifunction Tester (LCD Display)
4153 IN
-
Standard Electric Works Co., Ltd
Microprocessor-controlled. Measures Insulation Resistance, voltage (AC-DC) measurements with automatic hold facility, diode, ohm, and continuity with a short circuit current of minimum 220mA. Auto-off function. Energy conservation feature. Ener-Save™ limit the test duration to about 10 Seconds. Quick Test and EnerSave™ are unique features. Both saves energy. No moving parts. All calibration are saved internally in a non volatile memory. Easy calibration at any facility around the world. Operates with rechargeable batteries, alkaline or low cost general purpose batteries. Low cost maintenance, calibration, and ownership. Complies to all the latest regulations, including UK.
-
Product
High Voltage Power Supplies
-
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
Product
Programmable Multi Output DC Power Supply
LQ6324P
-
- Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation
-
Product
Process Gas Condenser/Chiller
-
Process gas chillers are designed to condense vapors out of a process gas stream so it may be collected and properly disposed.This chiller condenses Styrene (a gas that is regulated by the E.P.A.) out of a process gas stream. The chiller operated continuously at a -25C (-13F) outlet air temperature as long as the process gas stream was flowing.
-
Product
Stealth Large Bag Metal Detector
-
Stealth Large Bag metal detectors are custom manufactured to suit any large bag application. Stealth detectors use digital signal processing technology and have high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Product
SMD Testers
-
Is a miniaturized and integrated utility model measuring instrument, which can automatically identify components such as resistance, capacitance, diode, etc., with LED, voltage regulator, DCV, on-off and battery power measurement functions. SMD resistance, capacitance, diode (RCD) parameter measurement, is a good helper for electronics factories and electronics maintenance.
-
Product
DUT Prototype Board
DPB8800
-
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
Product
Micro Melting Point Instrument
DRK8026
-
Shandong Drick Instruments Co., Ltd.
Determine crystal melting point of the substance to make sure its purity. Mainly used for determining the meltingpoints of medicine,dyestuff,spice and other organic crystal compounds.Using photoelectric automatic detection, Dot matrix LCD display picture technology, digital keyboard input, and has the initial melting, final weld automatic display,automatic recording of melting curve, automatically determine the melting point of the mean value function. The temperature system uses highly linear platinum resistance as detection elements and PID regulation technology, improved the melting point’s precision and reliability. The instrument establishes communication with PC through the USB or RS232, printing or saving the curve and it uses capillary Pharmacopoeia as sample tube.
-
Product
Temperature and Humidity Regulator
H3431
-
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
Product
Clock Time Regulation For IPhone
ClockMaster
-
ClockMaster is a clock timing software, in many ways similar to watch timegraphers, but specifically designed to work with mechanical pendulum clocks. The app analyzes the ticking sound of the escapement to determine the clock's running rate measured in Beats Per Hour (B/H). This rate is then compared to a specified Target Rate, and the Error is reported as Seconds Per Day fast or slow (±S/D).
-
Product
Refrigerant Leak Detection Camera
FLIR GF304
-
The FLIR GF304 detects refrigerant gas leaks without interrupting or shutting down operations. Refrigerant gases are highly toxic, environmentally harmful, and heavily regulated. By detecting refrigerant gas leaks early, companies can avoid the cost of replenishment and limit environmental impact. The GF304 allows inspectors to visualize these gases, discover hidden leaks, and confirm repairs once their complete.
-
Product
Programmable DC Power Supply
CBCT
-
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
Rotational Speed Sensors
-
Rotation speed sensors are used to monitor, regulate and control mechanical drive systems and play a major role when it comes to protecting elements of a rotational system (e.g., in the engine, drive) from mechanical overload. Micro-Epsilon offers two sensor systems for rotation speed measurement. The capaNCDT CST6110 is a universal rotation speed sensor for counting tasks and rotation speed applications of any type. Moreover, the turboSPEED DZ140 measuring system is specifically designed for the detection of turbocharger rotation speeds.
-
Product
Rock Mechanics Testing Equipment
-
Rock mechanics is the part of geotechnical engineering that studies the behaviour of rocks under variable physical and environmental conditions. Testing is undertaken to enable the prevention of geotechnical failure such as shearing, by measuring the behaviour of rocks for compliance with regulations, design specifications and quality control standards.
-
Product
LED Car Audio Meters
OM-1
-
Some might consider the OM-1 to be over-built; we think it is just right. Some features of the design are:*Mil spec FR4 circuit board*Regulated power supply*Constant LED current and brightness regardless of battery voltage (won’t dim with your beat)*20 bright surface mount LEDs*Wide operating voltage range for vehicles with modified electrical systems
-
Product
Calibration Hangers And Weights
-
Calibrated Dead Weight are the official means by which torque analyzers and torque sensors are calibrated and are traced to National or International Standards, such as N.I.S.T, ISO and others. Many industries like as medical, aerospace, nuclear and others continuously calibrate their measuring equipment to comply with government regulations. For companies that prefer to have calibration capabilities in-house when their calibration requirements become extensive, they need calibration equipment.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Modular Designed CAMAC
CAMAC CERN-CE 1920W
-
WIENER provides a line of modular designed CAMAC crates compliant with ESONE and CERN standards. These CERN spec. CAMAC crates are configurable with linear regulated, low noise plug-in power supplies in the 300W ... 600W DC power range or up to 1900W with PS236 low-noise switching power supplies.
-
Product
Building Permit Expediting Services
-
Tejjy Inc. offers expert permit expediting services for construction projects in Washington DC, Baltimore, Maryland, and Virginia. We specialize in ensuring faster and hassle-free building permits for residential, commercial, hospitality, and federal design-build projects. Our comprehensive construction building permit management services focus on resolving permitting issues, handling the submittal process, and adhering to local building codes. With a deep understanding of the permit expediting process, we prioritize local regulations and submission procedures to obtain building permits efficiently. Trust Tejjy Inc. for reliable and precise permit management services.
-
Product
Bench DC Power Supply, Linear Regulation - Single, Dual Or Triple Outputs, Analogue Control, 30 To 130 Watts, Silent Cooling
EL-R Series
-
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
Product
Temperature and Humidity Regulator
H3021
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Consultancy Services
-
CellCare Technologies are experts in all types of standby battery servicing, specialising in automated monitoring, data acquisition systems, on-site battery management and maintenance, together with fault diagnosis and performance prediction. Our services also include product application and consultancy, plus training seminars on standby battery maintenance. Health & Safety courses to ensure compliance with COSHH regulations are also available.
-
Product
Test Services for EMC Compliance and Safety
-
Parker Chomerics offers a wide variety of EMI/EMC and safety testing for regulatory compliance. Tests include FCC, EC, VCCI, IEC 1000 (formally 801) EN 61000 Series, CISPR, Austel, MIL-STD-461 and EU regulations
-
Product
Regulated Power Supplies, Output 0 to 24 VDC, 400 AMPS, 9.6 KW, P/N 5944C2
-
- Regulated Power Supply, 9.6 KW P/N 5944C2- Input: 220 VAC, 3 PH, 50/60 Hz- Output: 0 to 24 VDC, 400 Amps max- Duty factor: 100%- Ripple voltage: <3% across full output range- Setting: 0 – 100% current and voltage- Control: Constant current and voltage control- Ambient temperature: up to 95 degrees F- cooling: Forced air-cooled- Dimension: 17.6″H x 19.9″W x 21.6″D- Weight: 175 lbs.- Degree of protection: NEMA 2
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
Thermal Microscope Stage
TS-4MP
-
With our TS-4MP Thermal Stage, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C
-
Product
AC/DC Linear Power Supply
-
Linear AC-DC power supplies are electronic devices used to convert electrical energy from alternating current (AC) to direct current (DC), providing a stable and regulated power supply for electronic devices. They are represented by the DA series.Linear power supplies of the DA series are characterised by their low output noise and high speed. They can be used as power amplifiers; a sinusoidal voltage of 8/10 Vpp can be superimposed on the test voltage up to a frequency of 50 kHz.Another application for this power supply family is the simulation of the curve of a photovoltaic panel by programming the voltage and current.
-
Product
35 W Triple Output, 6V, 2.5A & 20V, 0.5A
E3630A
DC Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The multiple output, 35-50 W, E3620A and E3630A provide dual and triple outputs; small, compact size for bench use; low-noise and excellent regulation; and overload indicator to monitor output. The Keysight 35W, triple output E3630A has three versatile outputs for benchtop applications; and is offers stable and reliable power plus essential features for manual testing.
