Ground Fault Locators
find an electrical cable's current leakage or fault.
-
Product
Fault Recording Monitors
-
Comprehensive, flexible, scalable and compatible – full multi-function devices.
-
Product
Voyager Intermittent Fault Detector
-
The Voyager includes a spread spectrum TDR so that the fault can be located. Once an intermittent is detected, the TDR is immediately connected to the failed test point and used to determine the distance to the fault.
-
Product
Utility Locating with LMX GPR
LMX200™
-
Unprecedented insights and target confidence. Detect traditionally non-locatable subsurface features:Non-metallic pipes, including PVC and asbestos cementConcrete storm and sewer systemsUtilities where installed tracer wiring has failedUnderground storage tanks and drainage tilesSeptic system componentsNon-utility structures such as vaults, foundation walls and concrete pads
-
Product
Fault Finder and Cable Length Measurement TDR
Snap Shot™
-
Accurately finds cable length, impediments in the cable and conditions at the end of every wire in your data, power, or communications/video system up to 3,000 ft.
-
Product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
Switch Module
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
Product
Pipeline & Cable Locator
STC-PCL 1101
-
Shanghai Stone Communication tech Co., Ltd
STC-PCL1101 Pipeline & Cable Locator consists of a Transmitter and a Receiver, used in the underground utilities route locating, the depth measuring and long distance tracing. We adopted multicoil electromagnetism technology on this Pipeline & Cable Locator, enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability, also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline. Thus it is widely used in the telecommunication, electric, tap water, natural gas, physical prospecting, town planning and so on.. STC-PCL1101 has many optional accessories, thus increased their use, and expanded their application scope.
-
Product
PXI Fault Insertion Matrix Modules
-
All of our fault insertion matrices feature a breakout arrangement that allows faults to be attached to the sensor lines via the Y axis. This includes the breaking of a connection or the adding of a series defect – all of which can simulate connectivity problems in the system. The three pin breakout versions allow the connection to be swapped for a “bad” sensor simulation.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator
910104126
Crimp Die
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator.
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
15" XGA Industrial Monitor For Hazardous Location, With "316L Stainless Steel Front Panel"
FPM-8151H
-
15" XGA TFT LCD with "LED backlight"Stainless steel 316L front panelIP65 compliant front panel-20 ~ 60°C (-4 ~ 140°F) wide operating temperature rangeEnhanced 5-wire resistive touch panelDirect VGA & DVI-D video input interfaceCombo RS-232 & USB interface for touchscreen functionSupports 24 VDC input and 100~240 VAC input (optional AC adapter)OSD control pad with lockable function on front panelCertified with UL CID2 for hazardous environment
-
Product
Battery Ground Detector
BGD
-
Battery Ground Detectors supply contact closures for alarm indications at precise ground fault resistance settings.
-
-
Product
PXI 1A Fault Insertion Switch 22-Channel
40-195-001
Relay
The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment under test: Open-Circuit, Short-Circuit between signal pairs, Short-Circuit between signal pairs and user applied fault conditions e.g. Power or GND. Relays in-line with the signal paths allow open circuit conditions to be simulated on either side or both sides of a signal pair. Relays between each channel pair enable adjacent signals to be shorted, and relays between signal paths and the "Fault" connection allow the application of external user applied fault conditions.
-
Product
Resistance, Ground Testing, Battery And Power Quality
-
Our testing equipment works wherever you are, whenever you need it, with precision and reliability.
-
Product
Multi-Function Transient Fault Recorder
TR-3000
-
The TR-3000 is the only tool you need to capture and diagnose power system anomalies. With multiple recording modes and continuous transient oscillography, you will never miss an event. The TR-3000 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. The TR-3000 takes the place of several devices: • Fault and Disturbance Recorder • Transient Fault Location • Phasor Measurement Unit • Power Quality Monitor • Sequence of Events Recorder.
-
Product
Multi-layer Short Circuit Locator
Toneohm 950
-
Polar Toneohms are ideal tools for the electronics production environment. Able to locate shorts quickly and accurately on both bare and loaded PCBs, they provide a very cost-effective means of minimizing repair and rework of faulty PCBs that have been identified by pass/fail testing on an ATE system.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
Multiplexer Module
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
Earth Ground Test Lead Kit
TL-796
-
*Earth Resistance Test Lead Kit*For use with IDEAL 61-796 3-Pole Ground Resistance Tester
-
Product
Rebar Locator
Profometer PM-600
-
Profometer PM-600 is an advanced cover meter for the precise and non destructive measurement of concrete cover and rebar diameters and the detection of rebar locations using the eddy current principle with pulse induction as the measuring method.
-
Product
Universal Ground Control Station
UGCS
-
UGCS is the common control station for the U.S. Army's Shadow®, Hunter and Gray Eagle™ unmanned aircraft systems. Built on a flexible crew station architecture, the UGCS can be configured and housed based on customer requirements, supporting a wide variety of assets and operations.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Cable Fault Point Identifier
OCFI
-
Shanghai Tarluz Telecom Tech Co., LTD
Optical Cable Fault Identifier (OCFI) is The latest instrument of optical cable maintenance, repair equipment developed by tarluz, it can identify the physical cable fault location easily. This is an essential tool for fiber optic cable repair!
-
Product
Long Spring Ground for ZD Differential Probe Qty 2
PACC-ZD003
-
Long spring ground for ZD differential probe Qty 2
-
Product
Fuse Circuit Breaker and Fault Finder
-
Shanghai Beha Electronics Co., Ltd.
*is a Fuse and Fault Finder which comprises of two parts: The Receiver and the Transmitter.*Locating and tracing of cables*Finding Circuit Breaker/RCD
-
Product
SAFE-T-GROUND - Ground Continuity Monitor / Control
TR-7
-
Model TR-7 Safe-T-Ground provides continuous monitoring of a truck's ground connection throughout loading operations. Static electricity is often brought in by tank trucks entering the loading area. The Safe-T-Ground Model TR-7 instantly stops loading operations if a tank truck loses its ground.
-
Product
Rebar Locator
Profometer PM-650 AI
-
The Profometer PM-650 extends the measuring modes of the Profometer PM-630 with the unique Cross-Line Mode and further analysis functions. The Cross-Line Mode allows users to measure the rebars of the first and second layer typically arranged in a rectangular mesh.
-
Product
64-Ch 1-Bus Fault Insertion
YAV91082
Fault Insertion Unit
64 channels 1 thread 2A 250V 1 Fault Insertion Buses Switching up 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Primary Cable Fault Locating
Directional Impulse Detector
-
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
Product
Earth Ground Resistance Meter
1623-2
-
The Fluke 1623-2 earth ground tester measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. With the stakeless test method, the Fluke 1623-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps.
