DC DC Converters
-
Product
Programmable Benchtop DC Power Supply
62000L
-
Chroma Systems Solutions, Inc.
Provides high quality yet cost effective programmable benchtop DC power, designed to meet the stringent requirements of the next generation of power electronics.
-
Product
Programmable DC Current Source
Model 121
-
The Model 121 programmable DC current source is a precision instrument suitable for bench-top use or panel-mounted operation in labs, test facilities, and manufacturing environments. It provides a low-noise, highly stable source of current up to 100 mA, with convenient manual selection through 13 pre-set output levels, each representing a ten-fold change in power when attached to a resistive load. A “user” setting allows the current output to be defined anywhere within the operating range of the unit, from 100 nA to 100 mA.
-
Product
synchro or resolver to digital (BCD) converters
AIT
Digital / Synchro Converter
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
Product
DC Leakage Current Monitor
MDLA-100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
Product
Linear DC Power Supply
-
A device that takes AC current (mains or line current, depending upon where in the world you are) and converts it into safe low-voltage DC at the desired voltage level.
-
Product
Bipolar DC Power Supply / Battery Simulator
IT6400 Series
-
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolar power source or a bipolar electronic load. The battery simulating function is especially applicable for development and high speed production testing of portable, battery-operated products.
-
Product
DC Electronic Load
3310G Series（75W~400W）
-
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
HIGH-VOLTAGE TESTERS 0-10kV dc UP TO 0-50kV dc
DV-100VA-5V
-
HIGH-VOLTAGE TESTERS 0-10kV dc UP TO 0-50kV dc
-
Product
DC Energy Meter
-
Multiple channels can be measured by a single meter, EN2450N & EN2450D. Differential current input for all the current channels. Programmable shunt secondary 50mV to 100mV. Programmable CT Primary for all channels up to 200A - for Hall Effect CT. Data logging for parameters such as Energy, Load hours and Ampere hours. Easy installation,Compact size, weight and simple wiring.
-
Product
DC REGULATED POWER SUPPLIES
IBL-RPS-3020
-
International Biological Laboratories
One channel output, Two Red LED digital output voltage and current value each, Constant voltage, current stabilizer, the two states can be auto-changeable, Current-limifing protection and limiting-dot adjustable optionally
-
Product
Coaxial Switch, DC to 40 GHz, SPDT
8765D
Coaxial Switch
The Keysight 8765 family of switches is designed for microwave instrumentation and ATE systems and features excellent electrical and mechanical performance. The Keysight 8765D is equipped with SMA connectors and operates from dc to 26.5 GHz with 3.5mm connectors and 40 GHz with 2.4 mm connectors. Option 292 can be ordered with Keysight 8765D. It is available with voltage option covering any drive voltage between 4.5 volts and 32 volts dc. Where performance data are required, Option UK6 includes a printout of test results. This switch is designed from the ground up for maximum dependability and performance. It is designed to operate within its specifications for more than 10,000,000 cycles.
-
Product
DC Regulated Power Supplies
-
PGP Electronics Private Limited
PGP Electronics Regulated Power Supplies are robustically designed to withstand rugged operation. PGP Electronics manufactures both the Standard and Custom-built power supplies. Manufacuring of custom-built power supples is our speciality.
-
Product
AC Hipot Tester /DC Hipot Tester
YD-Series
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
YD series HIPOT tester is applied to test the insulation ability of electric power equipments and insulation materials at power frequency high voltage. The insulation test result of the tester is go or not go. Also the YD series HIPOT tester is a universal power source in HV test. The maximum output voltage and capacity could be customized according the requirements of custom.The tester is consists of single HV transformer and main control box. There are two kinds of HV transformer according to the insulation materials of the HV transformer.They are dry HV transformer and oil HV transformer. For the dry HV transformer the insulation material is epoxy resin.For oil HV transformer the insulation material is insulation oil. The dry HV transformer has a smaller size and less weight than oil HV transformer. But the maximum output voltage is less than 100kv for dry HV transformer. The functions of the main control box are voltage output regulation, protection in emergency and voltage/current value indication
-
Product
AC & DC Analog Leakage Meters
507 EL
-
Standard Electric Works Co., Ltd
● Optional for pivot or taut band movement.● Compact and lightweight; easy to use and store.● Mirror scale: for easier viewing & reading.● Built-in stand makes reading and measuring easy.● 200μA full scale value.● Fuse-protected.● Low battery indication.
-
Product
DC REGULATED POWER SUPPLIES
IBL-RPS3002
-
International Biological Laboratories
One channel output, Two Red LED digital output voltage and current value each, Constant voltage, current stabilizer, the two states can be auto-changeable, Current-limifing protection and limiting-dot adjustable optionally
-
Product
Gridded DC Ion Sources
-
Ion-assisted processes like sputtering, etching, and surface treatment depend on a beam that’s stable, uniform, and tightly controlled. Gridded DC ion sources make that happen, giving engineers the precision they need to fine-tune ion energy and current density for reliable results.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
High Current DC Transformerd
-
High Current DC Transformer provides very accurate DC current measurements up to 3000 A with output current that varies directly with the input current in three ranges. This direct current transformer is designed with an open window to pass a single cable, set of cables, or buss bar that carry the direct current to be measured.
-
Product
Through Hole type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-45NK
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC earth fault measurement*DC leakage current measurement*Least affection from the magnetization of core and temperature fluctuation*Convenient ＋24V single polarity power supply
-
-
Product
DC Block
-
DC block offering broadband performance used to protect equipement and components from DC voltages
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
DC Blocking Power Splitter Combiner
PD5116
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
DC Blocking Power Splitter Combiner
PD5140
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
DC Bench Power
XDL Series
-
AMETEK Programmable Power, Inc.
The Sorensen XDL series II represents the "next generation" of high performance laboratory power supplies. The XDL provides multiple ranges for increased current capability at lower voltages and uses pure linear technology. Unlike other digitally controlled units, the XDL series II provides both numeric and rotary control while the illuminated keys and display legends provide instant confirmation of settings and status.
-
Product
DC Blocking L-Band Splitter Combiner
PD5960
-
INSTOCK Wireless Components, Inc
PD5960 is an IP67 outdoor, weather resistant, DC blocking, six way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5960 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 6 way power divider input rating tables for additional power handling info.
-
Product
Multiport Coaxial Switch, DC to 26.5 GHz, SP6T
87106C
Coaxial Switch
The Keysight 87106C multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87106C terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
Product
DC Ground Fault Locators
-
We currently offer one highly capable DC ground fault locator for sale to the United States, Canada and Globally. This fault locator is highly reliable and highly capable of locating any ground fault in a variety of settings. This one piece of ground fault locator equipment is all you will ever need to find any fault, in any location, in any system. With advanced computations and fuzzy logic it can very accurately display the insulation level of the tested circuit. We offer the best and only ground fault locator you will ever need. To learn more about his product please click below where you will also be provided key features and the ground fault locator specifications.
-
Product
DC Tester
-
The DC Tester is a Voltage and Ampere breakout for measuring DC current from 0-26V at 3.2A Max (when used with the USB Tester OLED Backpack). The DC jacks make it easy to measure a wide variety of devices by placing it inline between your power supply and your project without splicing cables, just like the
-
Product
DC In AC Clamp Tester
M-800P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Model 800P is the world’s first clamp meter which can detect small DC current in AC circuit in addition to general AC/DC current measurement.
