Telephone Line Testers
See Also: Telephone Line Test, Butt Set
-
Product
Falling Dart Impact Tester
FDI-01
-
Jinan Leading Instruments Co., Ltd.
FDI-01 Falling Dart Impact Testeris applicable in the impact result and energy measurement of the falling dartfrom a certain height against plastic films and sheets with a thickness less than1mm, whichwould result in 50% tested specimen failure.
-
Product
Handheld PD Tester
-
Weshine Electric Manufacturing Co., Ltd
TEV partial discharge inspection instrument uses two emerging technologies, transient-to-ground voltage (TEV) measurement and ultrasonic (US) measurement, to detect faults in switchgear. The equipment is portable and easy to operate. The TEV sensor is attached to the wall of the box, and the US sensor scans and detects along the gap on the switch cabinet.
-
Product
Line Scan Camera
8M Series
-
The USB Line Camera 8M is an easy-to-use cost-effective board-level line scan camera. It consists of two circuit boards, the main circuit board and the sensor circuit board.
-
Product
Torque Tester
DIS-RL series (05/2/6)
-
Tightening and final check of screws and bolts. Separate type digital torque driver/wrench. The detection part is very compact, and it is effective for torque measurement in narrow places and minute torque measurement. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Impulse Withstand Voltage Tester
SUG255
-
The Impulse Withstand Voltage Tester (or High Voltage Surge Generator), it is according to IEC255-5, IEC60060, IEC60065, GB14711, GBT17215.301 and GBT17215.322. It is suitable for doing all kinds of electrical and electronic products (such as energy meter, household appliances, low voltage electrical appliances and small power motor) insulation performance test.
-
Product
Tabletop Light Fastness Tester
TF421
-
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
Product
Cap Torque Testers
-
Imada cap torque testers measure cap tightening or loosening. The DTXS series cap torque tester can be used for rapid cap testing. The MTG allows for more accurate and repeatable results by maintaining a constant capping speed. Both testers have several ranges up to 85 lbf-in.
-
Product
Component Testers
-
After a wafer is tested through front-end test and back-end test, the component tester tests this final component or package assuring its quality for the semiconductor makers. DDR, DDR2, DDR3 memory component testers.
-
Product
Current Transformer Tester
HTCT-300
-
Full-featured, can not only satisfy various CT (eg: protection, measurement and TP category) but also PT type electromagnetic unit for its excitation characteristics (ie voltage current characteristics), ratio, polarity, secondary winding resistance, secondary load, ratio deviation, angle deviation and other test requirements.
-
Product
Cut Susceptibility Tester
-
King Design Industrial Co., Ltd.
Equipment conforms to IEC61730 MST12 specification. Pre- or post-round can be selected for control wiring connection. With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time. Equipped with rings at both front and rear end; used to connect a rope and control the driving direction. Use replaceable special cutting chip.
-
Product
Regular Battery Tester Models
-
The following are regular battery tester models for single-cell tests (coin cell/half cell/pouch cell/cylindrical cell, CT2001 & CT3001 Models) and supercapacitor test.
-
Product
Back Pressure Tester
TU29P
-
Enables Technician to test exhaust back pressure thru oxygen sensor. Oxygen Sensor adapter includes M12 & M18 thread.Special Gauge has two multi-colored bands - idle and 2500RPM, with pressures shown in PSA and bar.
-
-
Product
Circuit Breaker Tester
GDGK-303
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1) Closing and opening time measurement of 12 channels2) Max difference of closing or opening time measurement of three phases3) Bounce time and frequency measurement of breaker closing4) Circuit breaker closing and opening speed measurement5) Travel-time, Coil current-time curve of circuit breaker operation measurement6) Clearance of circuit breaker measurement7) Variable DC circuit breaker operation power supply8) Print test results by internal micro printers
-
Product
Mixed Signal JTAG Tester
JT 5705
-
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
Product
Automated Headlight Tester
VLT 0936/MK2
-
Fully computerized controlled CCD Head-light Beam Tester, with fully automated vertical and horizontal movements, with automated searching of the hot spot of the beam. This robot type Headlight Beam Tester is connected to the Vehicle Test Lane Computer system and displays instructions and results to one of the large overhead SVGA monitors of the Test Lane.
-
-
Product
Micro Vickers Hardness Tester
900-392
-
The 900-392 Micro Vickers Hardness Tester is engineered to produce a clearer indentation and hence a more precise measurement. By means of a 10 × lens and a 40 × lens the 900-392 vickers hardness tester has a wide measurement field and a broad usage range. Equipped with a digital microscope, it shows the measuring methods, the test force, the indentation length, the hardness value, the dwell time of the test force as well as the number of the measurements, all shown on its LCD screen.
-
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
Transformer Turns Ratio Testers
-
Transformer turns ratio testers from TRT series are DV Power instruments mainly designed for the measurement of power transformer turns ratio. Also, they measure transformer excitation current and phase shift. Special tests, such as automatic vector group detection and magnetic balance, can be performed on three-phase transformers and three-phase autotransformers.All models, except TRT03 series, have a built-in true three-phase power source, which is necessary for testing turns ratio of transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.DV Power turns ratio testers can output various test voltages for different applications. From the extremely low test voltage of 1 V AC that enables turns ratio verification of the majority of current transformers, up to the highest test voltage of 500 V AC that provides the most accurate turns ratio testing of power transformers used in power generation and transmission. By using the external booster, test voltage increases up to 5 kV AC in order to successfully test capacitive voltage transformers.All DV Power turns ratio testers have a built-in tap changer control unit. Because of that, it is possible to control the on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, the instrument and included DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions, and saving results. This option significantly facilitates and shortens the turns ratio testing time.TRT turns ratio testers use the same set of cables as three-phase winding ohmmeter & tap changer analyzers from the TWA series. Consequently, it enables one-time cable setup for performing eight tests:turns ratioexcitation currentphase anglemagnetic balancevector group detectionwinding resistanceon-load tap changer DVtestand demagnetization.
-
Product
Insulation Testers
AD-902
-
The instrument is designed for the direct measurement of insulation resistance of cables and electrical equipment especially in the telecommunications and communications. It can also serve as a tester for example go. Circuits or connectors.
-
Product
LAN Cable Tester PRO
PK-168 NextPRO S2
-
PK-168 is capable of wire mapping by pin & pair up to 600 meters,PK-168P: Remote unit come with PoE detector. It detects presence of PoE and displays type of PoE either end-span A or mid-span B or ultra power over 4 pairs and either 802.3af (PoE) or 802.3at (PoE+) is present.
-
Product
Automated ANSI Meter Tester
4 Series
-
The PowerMaster® 4 Series Automated ANSI Meter Tester boasts many features that make it the most functional, versatile, and user-friendly meter tester on the market today. It is a closed-link meter testing solution that sources current up to 30A or 50A (depending on model) and operates on all voltages up to 530V with no switch changes required. Our automatic meter testing equipment also facilitates testing of most ANSI socket-based meters using our newly-engineered universal zero insertion force meter socket.
-
Product
EOL Tester
-
Sterner Automation would like to introduce its new end of line (EOL) tester platform. Sterner Automation has been a supplier of calibration and test equipment to the automotive industry for over a decade and is now offering a standard hardware EOL platform that is configurable with a variety of software modules for seating plant applications.
-
Product
Coatings On Concrete Adhesion Tester
106/6
-
The Elcometer 106/6 Adhesion Tester has been specifically designed to measure adhesion strength of coatings on concrete.
-
Product
Rubbing Fastness Tester
-
Sataton Instruments Technology CO., Ltd
Rubbing fastness tester/Crockmeter is professional designed for determining the resistance of the color of textiles of all kinds, including textile floor coverings and other pile fabrics, to rubbing off and staining other materials in dry or wet conditions. Rubbing fastness tester can also be used to determine the color fastness to rubbing of ink, printing, dyeing, etc. There are two modes of manual and automatic for different requirements.
-
Product
COTS VME Board Tester
-
*Developed for support of Virginia Class Submarine at the COATS Integration Facility.*Provides Stimulus and Measurement Subsystem (SMS) to control, monitor, and evaluate VME assets used in the Non-Propulsion Electronic System (NPES) of the submarine.*Provides Native Environment Subsystem (NES) that simulates the operational configuration of typical NPES installations, and permits the test and evaluation of several types of VME assets.
-
Product
Package Drop Tester
-
The Package Drop Tester - PDT-II Series simulates the drop/fall of the packaged finished products to evaluate their damages. All the rhombohedrons, angles and faces of the package container can be tested. so that the manufacturer can know how to take measures effectively to protect Its products against damage during transportation. During dropping, the carrier will rotate to allow the packed products to fall freely.lt can test the faces, edges and corners of the product, with small vibration, and stable and reliable operation.
-
Product
Axis Play Tester
LMS 20.0 | VP 425017
-
Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
