-
Product
GFCI & Receptacle Tester
-
GFCI & Receptacle Tester - GFCI & Receptacle Tester for electrical work.
-
Product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1T1-6-S
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
Product
6-12V Circuit Tester
TE6-0704
-
Hangzhou Tonny Electric & Tools Co., Ltd.
Do-it-yourself quality. 6-12 volt tester. Tests circuits with power on. Reliable and economical. Tests circuits, lights and fuses. Lights for easy visibility. Durably designed for a long service life . For testing 6-12 volt systems for wire breaks, shorts, fuses, lamps, relays, armatures and more. Suite able for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses.
-
Product
Cable Tester
-
FST-500 High Voltage Cable Tester is a modular and customizable cable tester that can be easily adapted to various cable test or cable harness test applications. The electronics is based on Finero’s rugged industrial grade FST range of standard test equipment. All set and measured values are shown on alphanumeric display, additionally there is an analog panel meter for output voltage. Other cable paramerter like L, C and R can also be tested by using optional test and measurement equipment. The tester can be ordered with a build in PC and it can be used in conjunction with Finero’s Quality Control software.
-
Product
Fuel Display Unit Tester
MS 1125
-
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
Product
PSS PCB Tester
MS 1106
-
PSS PCB Tester is a powerful system used to test and validate DAWN (RWR & JAMMER) Support System boards. It has RS232/USB Communication for PC Interface.
-
Product
SOC Battery Tester
-
This sophisticated battery test equipment allows the battery tester to exercise and explore the battery’s internal profile and produce a true state of charge revealing the batteries true AHR capacity and ability to perform under load.
-
Product
5G Radio Communication Tester
CMX500
-
The R&S CMX500 radio communication tester is the future-proof solution for 5G NR testing, featuring an intuitive and flexible web-based user interface, the R&S CMsquares. Supporting manual interactive operation as well as automatically sequence-controlled test protocols makes the R&S CMsquares an advantageous software solution, with unique modules for all signaling use cases. These range from R&D design stages up to end-to-end application testing, production and conformance tests. The introduction of a one-platform strategy for all 5G NR test equipment enables a unified test environment for signaling and non-signaling testing through all stages of 5G device production.
-
Product
Sound, Light & Moisture Tester
-
Make safety compliance checks or perform acoustic analysis using a sound meter. Monitor and optimize light levels, reduce the energy burden of buildings by significantly increasing the efficiency of the lighting system with a light meter. Or check the moisture content of building materials for water damage or harmful mold growth, using a moisture meter.
-
-
Product
Brush or Sponge Pilling Tester
TF222
-
TESTEX Testing Equipment Systems Ltd.
Brush or Sponge Pilling Tester, to determine the pilling propensity and simulate normal wear of knitted and woven fabrics used in apparel and automotive interiors by brush and/or sponging specimens together in a circular motion to form pills. Specimens are evaluated under standard lighting conditions using a pilliscope, light cabinet or similar, against users’ standard fabrics or piling photographs.
-
Product
Hardness Testers
-
The hardness tester products you will find at PCE Instruments (PCE) are used for determining surface hardness. Each hardness tester uses a standard method of measurement. The measuring principles of most hardness tester devices are based on either the penetration of a diamond indentor into the material being tested or a calculation related to the force of the rebound after striking the tested material. However, material hardness can also be measured accurately through ultrasonic testing. Each hardness testing method has its benefits and will allow for the precise measurement of material hardness in accordance with the technical specifications of the hardness testing instrument.
-
Product
LINE-CORD AND MULTI-WIRE CABLE TESTERS
LCT-3
-
Model LCT-3 Line-cord tester is an automatic test set to check continuity, polarity and dielectric breakdown on three-wire line cords.
-
Product
Multi-Channel Hipot Tester
19020
-
The hipot test is one of the major test items in electrical safety testing. All electrical components and products including transformers, capacitors, power supplies, chargers and home appliances require hipot testing.
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Low Gauge Vacuum Tester
G4103
-
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
Product
Film Impact Tester
DRK136B
-
Shandong Drick Instruments Co., Ltd.
DRK136B Film Impact Tester is applicable in the precise impact resistance test of plastic films, sheets, laminated films, rubber and other nonmetal material.
-
Product
Alternate 2.65 (75.00) - 6.50 (184.00) Bead Probe
BTP-25F-6.5
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
100kV Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. Leakage current at real-time detection2. Alarm value can be preset freely3. Audio alarm, High-voltage breakdown protection
-
Product
IC Tester
ICE1
-
The IC Test System was developed to measure the EMC behavior of circuits (ICs) in the event of targeted field or line-related interference and for measuring emissions. The test IC is tested in function. The test environment ICE1 creates the functional environment of the test IC. The respective measurement task is carried out with the corresponding probe set.
-
Product
Cable Tester
LW3310
-
Dongguan Longwei Electronic Technology Co., Ltd.
LW3310 wire tester is designed for all kinds of electronic wire, electric wire and connector design, due to the various types of wire and connectors used in every field, this applies only to the commonly used wire detection instrument. Widely used in computer, communication, medical, electrical appliances, motor, automobile and other wiring test.
-
Product
Digital Earth Resistance Tester
8PK-ST1520
-
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
Product
Leeb Hardness Tester
-
Shenzhen Linshang Technology Co., Ltd.
Based on the principle of Leeb hardness measurement, the Leeb Hardness Tester, otherwise called as Leeb Rebound Hardness Tester, is considered as one of the most commonly used tools to test the hardness of the metal. It is a type of non-destructive testing tool used to inspect large sized workpieces weighing above 5 kg. Besides the hardness, it also measures the strength of materials.
-
Product
Open/Leak Tester
-
NIDEC-READ testers undertake various types of continuity tests at broad voltage and resistance levels.
-
Product
CDM Tester
-
Tokyo Electronics Trading Co., Ltd.
Determine what level of CDM discharge causes device damage by placing the device package on a metal plate with the pins facing up.
-
Product
Rubbing Fastness Tester
-
Sataton Instruments Technology CO., Ltd
Rubbing fastness tester/Crockmeter is professional designed for determining the resistance of the color of textiles of all kinds, including textile floor coverings and other pile fabrics, to rubbing off and staining other materials in dry or wet conditions. Rubbing fastness tester can also be used to determine the color fastness to rubbing of ink, printing, dyeing, etc. There are two modes of manual and automatic for different requirements.
-
Product
Energized Tester
ALL-SAFE PRO
-
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
Product
Smart SMD Testers
-
Precision Mastech Enterprises Co.
Compact, battery-operated, tweezer-like electronic tools designed for quickly measuring, identifying, and testing Surface Mount Device (SMD) components such as resistors, capacitors, and diodes.
-
Product
Film Permeability Tester
-
Film Permeability Tester is designed to test the permeability of a wide range of packaging materials such as plastic film, composite film, aluminum foil, thin sheets, rubber, porcelain, medical patch, etc.
