Digital Visual Interface
See Also: DVI
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5966-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.825-02
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
PMC Interface Card
CPCIC-MA4
Interface Module
The CPCIC3/6-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
C68-C68-D4 Unshielded Cable, 2X68-Position VHDCI Offset, 1 m
195949-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, Unshielded Digital Cable - The C68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is an unshielded, 50 Ω cable.
-
Product
Serial To Digital Interface Boards
-
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Product
PXIe-4081, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter
783130-01
Digital Multimeter
PXIe, 7½-Digit, ±1,000 V, Onboard 1.8 MS/s Isolated Digitizer, PXI Digital Multimeter—The PXIe‑4081 is the industry’s most accurate 7½‑digit DMM and provides the measurement capabilities found in two common test instruments: a high-resolution 1,000 V DMM and a digitizer. As a DMM, the PXIe‑4081 delivers fast, accurate AC/DC voltage, AC/DC current, 2‑ or 4‑wire resistance, and frequency/period measurements, as well as diode tests. In the high-voltage, isolated digitizer mode, the PXIe‑4081 can acquire waveforms at sample rates up to 1.8 MS/s.
-
Product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
USB-6525, 16-Channel, 60 V, 8 Solid-State Relays, 8 Inputs, Ch-to-Ch Isolated Digital I/O Device
779640-01
Digital I/O
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
Product
Digital I/O Vector Development Software
DIOEasy
Digital I/O
DIOEasy offers test engineers an efficient tool for developing, debugging, and executing digital test vectors for Marvin Test Solutions' GX5050 series, GX5150 series, GX5280 series and GX5291, GX5292, GX5293 and GX5295 dynamic digital instruments.Digital I/O (DIO) systems are very complex and typically require a substantial amount of programming effort to define data vectors. In order to simplify vector development, Marvin Test Solutions developed Windows-based DIOEasy, providing users with an easy to use interface. Toolbars and menus provide quick access to vector editing and viewing tools.
-
Product
VXI Digital Multimeters
Digital Multimeter
Maximize the use of your legacy test systems with our line of high-performance VXI digital multimeters.
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
NI-9476 / 779140-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 32 Channels
DN6.593-32
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Digital to Synchro Converters
DSP
Digital / Synchro Converter
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
Product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
Interface
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
Product
Interface
R15-MPCIE
Interface
The R15-MPCIE is very small (30mm x 40.95mm x 4.7mm) and lightweight for applications deployed in highly constrained environments where platforms require minimum SWaP solutions. It is designed for those working in avionics test and simulation for field and test support, and for use in data logging in which it offers significant advantages and flexibility.
-
Product
PXI-6508, 96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module
777598-01
Digital I/O
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
Product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
CAN Interface
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
Product
PXI-8431/2 , 2-Port, RS485/RS422 PXI Serial Interface Module
778984-01
Serial Interface
2-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 24 Channels
DN6.592-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
REM-11175, 16-Channel (Output), 24 V, 2-, 3-Wire Digital Module for Remote I/O
784745-01
Digital Module
The REM-11175 is a digital output module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and … individual modules mounted on a DIN rail. You control the REM-11175 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM-11175 features 2- and 3-wire spring terminal connection methods and circuit and overload protection.
-
Product
ARINC Interface Cards
Interface Card
- Wide Selection of COTS ARINC Interface Cards/Boards and Real-Time Appliances- 4-48 Shared and Dedicated, Independent RX/TX Channels- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk- Most Advanced Error Detection and Injection Available- Parametrics Variable Voltage on ENET-A429P
-
Product
Ethernet/LXI digitzerNETBOX 14 Bit High Speed Digitizer - 400 MS/s on 20 Channels, 20 Single-Ended Inputs
DN6.448-20
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI Digital Multimeter, 6 digit, Basic Features
M9181A
Digital Multimeter
The Keysight M9181A 6 digit PXI digital multimeter (DMM) offers the most common measurement functions at a low cost. The M9181A provides six built-in measurement types with all the reliability and stability you would expect from a Keysight PXI DMM.
-
Product
Visual Visual Inspection Device
IP-3000
-
Our visual visual inspection device Inspection Pro IP-3000 is an inspection device that quickly and accurately inspects the mounting board, which is constantly evolving, and judge whether it is good or bad without omission.
-
Product
Digital Input Board
VME-1128
Digital Input Board
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
Interface
RMAC-VME
Interface
Designed for laboratory simulation and production test applications, the Modular Avionics Controller (RMAC) is an intelligent, high performance 6U VME product supporting ARINC protocols and other serial communications. As an evolutionary follow-on product to the successful VME-AIC product line, the RMAC-VME provides a single integrated interface to multiple avionics protocols on VMEbus platforms.
-
Product
96-Channel Digital I/O Plug-In
1260-114
Digital I/O Board
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
Product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
CAN Interface
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
C Series Serial Interface Module
Interface Module
The C Series Serial Interface Module adds RS232 or RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the field-programmable gate array (FPGA) to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The C Series Serial Interface Module supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions. You can choose from both enclosed and non-enclosed modules.
