SCPI
A standard interface language between computers and test intruments.
-
Product
Smart GPIB Serial Interface Board
Model 4816
-
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Polarization Controller and Scrambler - MATRIQ
Controller
The Pol 1000 Series enables high-speed automated polarization control for polarization dependent testing procedures.Rotate or scramble the polarization of your signal with no need for manual adjustment of paddles or tension screws using intuitive software, LabVIEW or comprehensive SCPI commands.
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
Wide-range Programmable DC Power Supply
IT6900A Series
-
IT6900A series wide range programmable power supply have built-in standard RS232, USB, GPIB, RS485 and analog interface (RS485 and analog interface are just for IT6900B), support SCPI protocol, facilitate remote control, industrial PLC control and the formation of intelligent test platform. Remote compensation terminals avoid the problem of inaccurate testing caused by voltage drop on the wire.Low ripple, low noise and built-in digital voltmeter make IT6900A easy to do external measurement.IT6900A can be widely applied in DC-DC power supply module, battery charging and sensors and other test areas.
-
Product
GPIB Relay Interfaces
-
*ICS's GPIB to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the GPIB to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any GPIB programming language. Use ICS's interactive GPIB Keyboard program for easy operation from your PC without having to write a program.
-
Product
ANSI X3.28 to Modbus RTU Converter
Model 2399
-
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
Product
DC Power Supply, 6V, 5A, 30W
E36100 Series
-
Keysight E36100 Series basic DC power supplies feature a compact size (2U, -rack), a high-contrast OLED display that is viewable from any angle, and modern USB and LAN (LXI Core) connectivity. They also include low power current measurement capability and overvoltage, overcurrent, and overtemperature protection. You can control these power supplies via the intuitive front-panel interface, a Web interface running on a browser, a SCPI or IVI program, Keysight IO Libraries, or a BenchVue app running on your PC or mobile device.
-
Product
Single Channel Oscilloscope 20M-100MHZ
HDS
-
Shenzhen Chuangxin Instruments Co., Ltd.
- Auto-scale function- 20 automatic measurements- Bandwidth : 20MHz - 100MHz- USB data transmission supported- Waveform record and replay- Multimeter newly supported SCPI- Rechargeable Li-ion battery (6 hours' backup)
-
Product
GPIB Serial Interface
Model 4804B
-
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Functions as a GPIB-to-Serial Interface (G-Mode) or as a Serial-to-GPIB Controller for a single device (S-Mode).* Over 600 Kbytes/second GPIB data transfer rate.* Transparent data transfer.* GPIB Address can be set by SCPI commands, by an external rocker switch or by a serial command.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Product
Electronic Fuel Injection & Ignition Spark Tester Kit
36310
-
Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Contains Cat. No. 36300, Noid Light Set to test electronic fuel injection signals and the Cat. No. 23900, In-Line Ignition Spark Checker to trouble shoot the ignition system (Shows a duplicate view of the ignition spark). Supplied with Noid Lights to check Bosch PFI, Ford TBI, Geo TBI, GM PFI, GM SCPI and GM TBI.
-
Product
Tunable CW Laser Source
IQTLS
-
The IQTLS is a continuous wave (CW) laser source combining high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability. Available in single or dual laser configurations, this tunable laser source can be controlled locally via USB or Ethernet ports and is SCPI VXI-11 compliant.
-
Product
Breadboard Module for 34980A
34959A
Breadboard Module
The Keysight 34959A module for the 34980A Multifunction Switch/Measure Unit can be used to create custom designs inside the Mainframe. You can control your circuits with access to both the +12V and +5V supplies, 16 GPIO ports, and 32 relay drive lines. The faceplate has cutouts for the most common connectors. The breadboard module can be programmed using standard read and write commands in SCPI.
-
Product
Serial-to-Daq Minibox
Model 2367
-
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
Product
GPIB Smart Serial Interface
Model 4866
-
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
USB Controlled Multi-Function DAQ For ATE Education And ATEasy Training
GT98901 Series
-
The GT98901 Demo board is a USB controlled, cost-effective, multi-function PCB assembly. The module is completely self-contained and includes an LCD display, measurement and stimulus resources, digital I/O, relays, and switches – all of which can be accessed and monitored via the USB port using a SCPI command set via a USBTMC interface which supports the USB488 protocol. Power for the board is provided via the USB interface, providing a totally self-contained assembly which can provide users with a simple yet complete vehicle that replicates many of the stimulus and measurement functions associated with ATE systems. When combined with Marvin Test Solutions' ATEasy® Test Executive and Test Development environment, the GT98901 is the ideal product for creating and supporting ATE training and education applications.
-
Product
Noise Figure Meters
H5M Series
-
*Frequency range from 10 MHz to 4/20 GHz*Noise Ratio and Gain measurements*Frequency converter measurements with a fixed or external heterodines*Built-in thermostatic YIG preselector*High measurement speed*Extend the NFA solution up to 50 GHz with special downconverter unit*SCPI Language Compatibility
