PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
product
PCI Express Passive Switches
MAX4888A
High-Speed PCI Express Passive Switches Enable Gen II Switching
-
product
PCI Express 2-Port
7203e
The 7203e PCI Express serial interface provides two optically isolated serial ports, each individually configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C952 UART with 128-byte Tx/Rx FIFOs that enables data rates to 460.8K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
product
PCI 6 Channel Precision Resistor Card
50-297-003
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI-5922, 24-Bit, Flexible Resolution PCI Oscilloscope Device
779659-02
24-Bit, Flexible Resolution PCI Oscilloscope Device - The PCI‑5922 high resolution oscilloscope device features a flexible measurement resolution range up to 24 bits and up to 15 MS/s rates. This oscilloscope device has flexible settings for coupling, and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PCI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and any other small, accurate signal measurements.
-
product
PCI Data Acquisition Boards
DA14-100DMA Series - Dual 14-bit D/A, 15 MS/s
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm
50-294-012
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Compact PCI Connector Board
cPCI-J2-SCSI
Ribbon cable is used between the rear IO and SCSI connector. The lengths are reasonably well matched. The cable is short. The design is intended for lower speed IO - 10 MHz and below. Above 10 Mhz there may be some attenuation.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PCI Express 4 Base Specification Receiver Test Automation
N5991PB4A
The N5991PB4A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 4.0 ASICs.
-
product
16-Port PCI Express
PEX 8764
The ExpressLane™ PEX8764 is a 64-lane, 16-port, PCIe Gen3 switch device developed on 40nm technology. PEX8764 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
product
Low Profile PCI Express 8-Port
7803ec
The 7803ec low-profile PCI Express serial interface provides eight RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps. These features make the 7803ec ideal for data-intensive applications that require reliable, fast throughput rates.
-
product
Flexible MiniPCI Express to PCI Adapter
SKU-034-0X
Flexible MiniPCI Express to PCI Bus Adapter (Adapter) was designed to convert the MiniPCI Express bus into two 32-bit PCI buses. It allows to connect up to 2 32-bit PCI expansion boards to the motherboard MiniPCI Express connector (supports full-size and half-size MiniPCI Express host boards).Adapter includes a PCI adapter, MiniPCI Express host board (full-size or half-size) and PCI Express flat Cable.
-
-
product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 26.7kΩ
50-298-132
The 50-298-132 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 26.7kΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Bus Signal Amplifier
3322
Model 3322 is a 3U single-slot, PCI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3322 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
product
PCI Express, Power, USB Cables for Amfeltec Products
PCI Express, Power, USB Cables for Amfeltec Products
-
product
14 bit, 125 MS/s PCI Digitizer
ATS460
ATS460 has been designed from the ground up for OEM applications, which require very high reliability, high performance, high quality and reasonable prices. ATS460 uses COTS analog components and FPGAs to provide you more features and benefits and at the same time reduced manufacturing costs without compromising quality. The result is that you get more digitizer for less money.
-
product
12-Bit PCI Express ADC/Digitizer
SIS1350
The SIS1350 is our first PC add on digitizer card. It was developed for high repetition rate acquisition of short analog signals (i.e. up to 128 µs at 500 MSPS) with good resolution
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
PCI Express, IEEE 488 GPIB Instrument Control Device for Linux
779779-01
The PCIe‑GPIB is an IEEE 488 controller device for computers with PCI Express slots. You can use this device to integrate an instrument into your system using GPIB. The PCIe‑GPIB achieves maximum IEEE 488.2 transfer rates. With an onboard bus master DMA controller, there is no microprocessor interruption in data transfers. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB. The PCIe‑GPIB includes a low-profile bracket option as well as a kit that includes the NI‑488.2 driver for Linux®. Regardless of which PCIe‑GPIB you purchase, the device is compatible with Windows, Linux®, and Mac OS X. Linux® is the registered trademark of Linus Torvalds in the U.S. and other countries.
-
product
PCI Express Mini Card Products (mPCIe)
PCI Express Mini Card, commonly abbreviated as mPCIe, or Mini PCIe, is a newer form-factor for PCI Express devices. Designed with the older Mini PCI standard in mind they are the same basic form-factor (commonly used in small-form-factor devices like laptops and other portables) but lack the retention clips of Mini PCI. Unlike the original PCI Express bus, Mini PCIe provides both the standard PCI Express and USB 2.0 signals, allowing flexibility in peripheral design. The standard is highly suitable for industrial automation and test in vehicle, mobile, or any other shock / vibration sensitive application.
-
product
Mobile PCI Express Module with NVIDIA® Quadro® Embedded P5000
EGX-MXM-P5000
Meeting the needs of embedded, ruggedized, and mobile system builders, ADLINK's EGX-MXM-P5000 Embedded MXM GPU Modules utilizes Quadro Pascal architecture to deliver superior graphics and computing performance. The EGX-MXM-P5000 is specifically purposed to accommodate form factors incompatible with conventional PCI Express cards, and is built to maintain operations under a wide range of thermal and other environmental conditions. It’s the ideal choice for blade-based and other deployments where high GPU density is critical, with a choice of GPU memory capacity, extremely reasonable power requirements, and flexible display options.
-
product
Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6332
Our Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6332) adapts two single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
product
PCI card with 3 IP sites
PCI3IP
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
product
PCI Express® Bus To 3U PXI Express™ Chassis Expansion Kit
ACL-EXPRESS-7
The PCIe-to-PXIe expansion kit includes one PCIe-8560, one PXIe- 8565, and one ACL-EXPRESS cable (7 meters).
-
product
Quad PCI Express, Hot-Plug Controllers
MAX5960
The MAX5959/MAX5960 quad hot-plug controllers are designed for PCI Express® (PCIe) applications. These devices provide hot-plug control for the main 12V, 3.3V, and 3.3V auxiliary supplies of four PCIe slots. The MAX5959/MAX5960s' logic inputs/outputs allow interfacing directly with the system hot-plug management controller or through an SMBus™ with an external I/O expander such as the MAX7313. An integrated debounced attention switch and present-detect signals simplify system design.
-
product
Basic 3U Rackmount Appliance for PCI Express® Gen5
R300-G5
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols.
