Current Clamps
measure AC or AC-DC amperage without contacting conductors.
-
product
Low Voltage High Current DC Electronic Load
N62400 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N62400 series is developed based on NGI's years of experience in testing for fuel cell. It is with high accuracy, high reliability and high cost-effective. N62400 series is with high power density and elegant appearance, which is available for benchtop use or installation in 19 inch cabinet.
-
product
Earth Resistance Clamp Meter
T2100
Clamp meters for measuring earth resistance directly on earth rods (STAKELESS METHOD) and compatible with MacrotestG series meters
-
product
Clamp Meters, Clamp Multimeters
Hioki provides a wide range of models for AC, DC, and leakage current measurement. The lineup also includes DC high-voltage probes for measuring the open-circuit voltage of high-voltage solar power (PV) systems. Models that can be easily inserted into narrow gaps between cables and transmit data to smartphones or tablets improve operational efficiency.
-
product
Rogowski AC Current Probe
RCP500
Shenzhen Micsig Instruments Co., Ltd.
Adopts the Rogowski coil current measurement system: within the range, the output signal of the system and the current signal to be measured are always linear, so the accuracy will not change with the current; The RCP500 measures AC current up to 500A pk, minimum to 200mA pk, with bandwidth ranging from 15Hz to 300KHz, 1% accuracy, and has less than 2mV noise. Directly powered by Micsig UPI interface, realise auto scaling setup,
-
product
Multi-Channel, Programmable Current Source
CS-48-100
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
product
600A Digital Clamp Meter
7128C
Peaceful Thriving Enterprise Co Ltd
This is an auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC/DC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity, frequency and non contact voltage sensing. Sub switch included Function Select, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Hz/Duty Cycle, Illumination and Back-light.
-
product
Current Measurements Of PWM Or Inverter, AC/DC 1～50A, Φ16mm
CTF-50DC-U24V
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 1～50A*Current measurements for PWM or inverter
-
product
Flexible Rope-Type Current Probe
RCT1A and RCT5A
These probes have great bandwidth ensuring accurate measurement even with harmonically distorted wave shapes. For all RCT1A/RCT models, a NIST, NAVLAP, NPL (UKAS) factory traceable calibration certificate and certificate of conformance is supplied. UL/CSA approved materials are used throughout. Three phase and single phase flexible AC current sensors (rope sensors) are available for fast installation in confined spaces, eliminating the need for Electrical Supply Shutdown. Available outputs are 1A @ 2.5VA and 5A @ 0.5VA, this means long cable lengths from current sensor to signal conditioner allow these low VA ratings to be used, even when feeder cable to energy meter distances are large (up to 98 feet / 30 meters)
-
product
Electrolytic Capacitor Leakage Current Meter
TH2686C
Changzhou Tonghui Electronic Co., Ltd.
■ Test voltage: 0-200V, 0-500V ■ Voltage accuracy: 2% set value + 2 words ■ Measuring range: 0-30mA, 10 gears ■ Current accuracy: 2% of reading +0.5 grid
-
product
L.V. Current Transformers
ENTES LV Current Transformers are measuring transformers which transform the primary current by a specified ratio to its secondary side with a phase difference of 0 degrees. They provide isolation of the relays and measuring devices from the HV side of the network.
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Quad 6-Channel, 1-Pole
42-514-106
The 40-514-106 (PXI) and 42-514-106 (PXIe) are low density multiplexers in quad 6-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
Primary Current Injection Tester
SLQ
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
It's a high voltage generator insutrment for tesitng.
-
product
Digital Current Integrator
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
product
Split type AC Current Transformer
CTS-300
MULTI MEASURING INSTRUMENTS Co., Ltd.
*5A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy to install by metal fitting.
-
product
Broadband Current Probes
Conducted currents can be measured without making direct contact with the source conductor or metallic surface by means of clamp-on broadband current probes. The BCP-5xx EMC Current Probes are designed to permit field intensity meters, spectrum analyzers, and other 50W impedance instruments to measure quantitative magnitudes of current.
-
product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL DU
The 72-7226 CAL DU from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
-
product
Primary Current Injection Test Trolley
SCR ELEKTRONIKS have developed primary and secondary Current injection test trolley for Switchgear manufacturers for testing of ACB , MCB , MCCB. It is low Voltage high Current source with control circuitry, digital read out for test current and trip time measurement. We can select different links of CT range as per the required test Current.
-
product
Fuse Buddy Current Loop
307M/308B
*Just clamp your current probe over the loop to access the amperage draw through a fused circuit. *Easy testing access, plugs right into fuse socket, no more hand made adapters. *Testing range 0-30 Amps - Do Not Exceed 30 Amps
-
product
ITA, iCon, Extended Cable Clamp
410123115
This iCon ITA includes an extended cable clamp to accommodate larger cable bundles. The maximum cable bundle area = 1.97 " sq. or a 1.58"/40.13mm diameter bundle. The clamp may be inverted for smaller cable bundles.Please note: This ITA does not offer an increased bend radius that may occur with a larger cable bundle radius. Larger bend radius is offered by the iCon XL, p/n 410123232.
-
product
Leakage Current Tester and Clamp-On Earth / Ground Resistance Tester
10µA Ultra High ResolutionLarge Conductor Diameter (30mm)AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A)Wide Frequency Response (40Hz-1KHz)ACA, ACV, Ω and ContinuityLarge 3¾ Digit LCD (4000 Count)40 Segment Fast Bargraph Display (20 times/sec.)Data Hold and Max / Min HoldRelative Measurement600 Vrms Overload Protection in Resistance Range
-
product
Primary & Secondary Current Injection Testing Sets
Primary current injection kits are used to test and commission Circuit Breakers, Bus Bars, CTs, Relays, MCCs, PCCs etc. These are also used for high current injection and simultaneously measuring voltage drops and hot spots in bus-bar joints, Circuit Breaker Contacts etc.
-
product
Current Probe
PA-677
*Max. 70ADC/140Ap-p*Sensitivity: ≧2mA*Bandwidth: DC~1MHz*Rise Time: 0.35μS*Over Range Function*50mV/A, 500mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
42-514-104
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
16-Ch SPST 10A-277VAC High Current
YAV90086
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Current Transformers Test Set
Supreme Instrument Laboratories
The basic unit is sensitive magnetic comparator and also it incorporates electronic null detector to facilitate the balance. The reference Current 5A. or IA. obtained from Standard Current Transformer and in comparison to that the vector length and phase displacement is measured. The ratio error in percentage and phase displacement in minutes are directly compared and indicated on dials.
-
product
DC Current Shunts
DC current shunts / standards are true 4-terminal devices that precisely measure DC currents from 10 A to 10,000 A. They use special alloys in the resistive elements which are supported on an insulating base for mechanical stability. The 9230A includes special features to reduce the effects of power dissipation and associated self heating errors. These shunts are designed to operate in air at full rated current. These are the best performing, and most widely used, DC metrology shunts in the world.
-
-
product
High Current DC Load
3350F Series
3350F has its own control and display panel, CC/CR/CV/CP/Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB, RS232、USB and LAN interface.
-
product
True RMS Wireless Clamp Meter w/ Differential Temperature & DC Amps
DL429B
UEi Test & Measurement Instruments
The DL429B Clamp meter offers users True RMS precision, dual temperature, a voltage and amp range that will extend applications to ECM motors, variable speed DC motors, plug and play DC motors and AC ductless mini splits. It also has Wireless capability and a free App.
-
product
High Voltage, High Current Linear Amplifier
P200
The P200 is a general purpose linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device.
