Igniter Testers
-
Product
SECONDARY IGNITION PICKUP
MD75300
-
*Safely acquire high voltage waveforms with this high impedance, active pickup*Works with spark plug wires and coil on plug ignitions with MDAUTOWAVE, AUTOWAVECAMO and MDAUTOWAVE2*Adjustable sensitivity increases waveform acquisition accuracy
-
Product
Ignition Pulse Detector
IP-3000A
-
IP-3000A Ignition pulse detector is a slim and light weighted detector by using amorphous metals fiber element. It is 1/4 in thickness (mass: approx. 1/50) and 1/3 in weight compared with the previous model of Ono Sokki. Also the IP-3000A can obtain constant output from low to high rotation with high sensitivity.Meeting the needs of structure or mechanism in recent gasoline engines, the IP-3000A can easily clamp around an ignition coil cable (the primary side cord of ignition coil or the current cord of electronic distributor). Moreover, heat-resistant design up to maximum operating temperature of +120 C° enables measurement under harsh environment.The IP-3000A Ignition pulse detector can be used with Ono Sokki’s engine tachometer.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Ignition Pulse Detector
IP-3100
-
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
Product
In-Circuit Testers
-
SPEA’s Bed of Nails Board Testers are scalable In-Circuit Test platforms that deliver the shortest test time, superior diagnostic accuracy, and extended test coverage for the most comprehensive range of electronic products.SPEA’s In-Circuit Board Testers are designed to increase yield, shorten the testing time, and cut the cost-of-test. Thanks to their unique Multi-Tester and Multi-Core Architecture, the SPEA’s Board Testers provide up to ten times greater throughput than conventional ICT test systems.
-
Product
Polarization Tester
-
Polarization Tester is used to measure the stress value of optical glass, glass products and other optical materials, and is widely used in pharmaceutical companies, glass products factories and laboratories.
-
Product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
Receiver Tester
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
Product
Form Testers
-
The highly accurate rotary table machines and spindle form testers of the RONDCOM series can be used in many areas: production, measuring room and calibration lab.
-
Product
EMF Testers
-
TES Electrical Electronic Corp.
Frequency range 10MHz to 8.0 GHz3 axis isoltropic measurements of EMFNon-directional measurement with three channel measurment probe. High dynamic range.Configurable alarm threshold and memory function.
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
Vibration Testers
-
Guangzhou Amittari Instruments Co.Ltd
The Vibration Tester can display the parameters of “Displacement”, “Velocity” and “Acceleration” simultaneously; Applied to the periodic motion measurements to detect moving mechanical imbalances and misaligned. Designed for on-site measuring various mechanical vibration, for quality control, running time and prior equipment maintenance data. Selection of high-performance accelerometers to achieve accurate, replicable measurement It has a bearing condition measurement function.
-
Product
CDM Tester
-
Hanwa Electronic Ind. Co.,Ltd.
The tester implements to test the withstand voltage which occurs when the device contact to different electric potential object.
-
Product
Compression Testers
-
Compression testing is a mechanical procedure for determining how a test sample will react to a force being applied across one side of the test sample.
-
Product
Unbalance Tester
BK2027
-
If you need to test displacement in hard drive motors with speeds up to 10,000rpm, think about BaKo's Type BK2027 Unbalance Tester. It's both easy to set up and easy to use and as a 2 channel DSP based system, it can test 2 motors at once and display the balance results as either unbalance (cm.g), acceleration (m/s2) or vibration strength (g).
-
Product
Flexing Tester
-
Premier's Flexing Tester are used to check how much the bending movement of the cord influences the electrical and mechanical connection. The equipment is motor driven, turning forward and back at required angles. A counter provides an automatic stop of the testing after a pre-set amount of test cycles. Set of weights are provided as per requirement.
-
Product
Continuity Testers
-
The extremely versatile continuity tester offers an insulated, shock-resistant and break-proof plastic housing. The pluggable and screwable connection between the test leads and the terminal post is safe to touch. The continuity test is indicated by an acoustical and an optical signal. The integrated torch light allows you to find wires quick and safe under though circumstances.
-
Product
Drive Tester
Disk Manufacturing Module
-
SCSI Toolbox LLC is proud to announce the Disk Manufacturing Module, joining a decade of real-world drive testing experience with input from hundreds of customers to bring the best new testing tool to the disk manufacturing and integration marketplace.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Battery Testers
-
Shanghai Beha Electronics Co., Ltd.
*can measure the resistance of rechargeable batteries and DC voltage.*can also test Ni-cd, Ni-MH, Li-ion batteries.*DC Voltage measurement.*4-wire resistance measurement.
-
Product
Cable Testers
LINKMASTER
-
The LinkMaster Tester consists of two units. The main unit is connected to one end of the cable to be tested and the remote unit is connected to the jack at the far end of the cable (wall outlet, patch panel port, etc.)
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Tensile Tester
-
Wewon Environmental Chambers Co, Ltd.
Is a fundamental materials science test in which a sample is subjected to a controlled tension until failure
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
-
Product
Torque Tester
NDI-800CN/80CN
-
Ideal for daily inspection of electric screwdrivers. Enhanced visibility, ease of use, and ease of connection. The easy-to-read color display, addition of a clock function, and simple operation with dedicated software enable more advanced management. Efficient measurement without unwinding work by "OW joint".
-
Product
HIPOT testers
HypotMAX III
-
Patented SmartGFI® functionStorage of 50 test setupsRemote Safety InterlockUSB/RS-232 or GPIB interfaces availableAdvanced menu driven controlDigitally controlled arc detection systemCHARGE LO® & RAMP HI® systems
-
Product
Torque Tester
DIS-IP Series (-IP05/5/50/200/500)
-
For managing various manual torque wrenches and torque drivers. Standard product for static torque measurement. Display characters are larger, improving usability. Installation in a small space is now possible with the separated type. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Insulation Tester
CENTER 360
-
4 Digits LCD Display, Auto Range For MΩ & Ω, 40 Segments Analog Display, Test Hold Function For Easy Operation, Automatic Zero To Null Lead Resistance
-
Product
Rubber Testers
-
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
Product
HDBaseT Tester
-
The MS-TestPro is the only HDBaseT tester that is all-inclusive, 100% reliable, portable and affordable, making it an indispensable tool for all installers and integrators. It provides AV professionals with all the information that they need while in the field to enable them to verify the integrity and stability of every system tested down to the last detail. Moreover, the MS-TestPro generates a report including all the parameters necessary to certify link quality and status up to 4K Ultra High Definition. The report can then be transferred to a computer or even to a smartphone for use by both installer and end-user.
