Surface Resistance
-
Product
Moisture Resistance/ Humidity Test
-
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
Product
15" XGA Industrial Monitor With Resistive Touchscreen, Direct-VGA, DVI Ports, And Wide Operating Temperature
FPM-3151G
-
15" XGA LED backlight LCD with low power consumptionRobust anodized coated aluminum front bezel and stainless steel rear coverSupports wide operating temperaturesIncrease reliability by enhanced 5-wire resistive touch sensorAnti-reflective screen with tempered glassFull enclosure ground isolation protectionSupports VGA/DVI input, dual touch interfaces and two power inputsFront lockable OSD membrane keys with user-defined brightness settingFront panel is IP65 compliantSupports panel, VESA, wall and desktop stand mounting
-
Product
Handheld Turns Ratio & Winding Resistance Tester
TWR-H Series
-
Handheld TWR-H device is DV Power single-phase instrument designed for measuring transformer winding resistance and turns ratio.The instrument has two output DC sources for measuring transformer winding resistance. The first DC source can output up to 2 A DC and is used for injecting current to the transformer’s high voltage winding. The second DC source can output up to 10 A DC and is used for testing the transformer’s low voltage winding. This is especially useful when measuring winding resistance of distribution transformers. These transformers have large turns ratio and therefore a big difference between resistances of high voltage and low voltage windings. Upon the winding resistance test, it is also possible to demagnetize the transformer core. The demagnetization process is completely automatic and safe.Together with the turns ratio, the instrument also measures excitation current and phase shift. This enables detecting transformer core or winding turns failures which cannot be spotted by measuring turns ratio only. The instrument can output test voltage up to 40 V AC for this test, but it can also output a very low test voltage of 1 V AC which is necessary for turns ratio verification of the majority of current transformers.TWR-H is powered by an internal Li-Ion battery. Up to 100 tests can be performed with a fully charged battery.
-
Product
IST(5KV~15KV)High Voltage Micro Ohm Meter,Insulation Resistance Tester Kit
-
Chongqing Assen Power Equipment Co., Ltd
ISF High Voltage Ohm Meter has a large LCD screen gray backlit display, data storage, data access, alarm, and automatic shutdown functions.
-
Product
High Coil Resistance Reed Relays
Series 118
-
The Pickering Series 118 is a range of very sensitive reed relays that are ideal for portable electronic instruments or other applications where low power consumption and a very small footprint is important. They have 5 volt coils with a resistance up to 2200 Ohms and the option of an internal diode.
-
Product
Easy and Non-Destructive Airflow Resistance Measurements of Materials and Parts
CARE+
-
The control of airflow resistance in the production of materials and components is a growing requirement in the automotive industry. CARE+ (Concentric Airflow Resistance Evaluator) is an apparatus designed to measure the airflow resistance of materials and parts. Measuring non-destructively, CARE+ is particularly applicable in the quality control of parts and materials.
-
Product
3 Wire (Digital) Earth Resistance Tester
ST-1520
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
Product
Digital Earth Resistance Tester, ERT-1502
-
Our Earth Tester is a very successful replacement of the conventional generator type hand tester. This device is most extensively used to test the earthing installation in numerous power based industries, electrical traction systems and telecommunication networks.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS HL
-
Optik Elektronik Gerätetechnik GmbH
Measuring instrument for contact angle and surface free energy, special solution for semiconductor technology for wafers up to 300 mm.
-
Product
Global Standard Model For 4 Point Probe Sheet Resistance Automatic Measurement System
RT-3000/RG-1000F
-
*Fully automatic system for large sizes of flat panel with glass loading robot*Tester self-test function, Measurement position correction function, wide measurement range*Min. 0.1 mm meas. resolution and user programmable test pattern*Host (CIM) communication and 2-D/3-D Mapping software
-
Product
UV Weather Resistance Test Chamber
-
This series is applicable for the sunlight resistant test of nonmetallic materials and aging test of artificial light source.
-
Product
Surface Cleanliness Analyzer
Surface Analyst
-
The Surface Analyst is a fast, easy, accurate, and non-destructive instrument that quantifies your level of surface preparation from the lab to the manufacturing floor. In 2 seconds, the Surface Analyst determines the surface cleanliness level by providing the contact angle measurement and a pass/fail result.
-
Product
Skid (Portable Skid Resistance Tester)
-
(also known as the British Pendulum Tester) is an essential tool for anyone with a duty to minimize the risk of accidents arising as a result of slippery roads and floor surfaces. This device is also used to investigate the cause of accidents after they have taken place.
-
Product
Surface Photovoltage
-
The surface photovoltage spectroscopy modules are the perfect all-in-one solution for in-depth studies of light sensitive materials such as organic semiconductors, solar cells or light sensitive dyes.
-
Product
Winding Resistance Meter 50Amps, 3 Channels Rack
WR50-13R
-
Raytech Digital Winding Resistance meter WR50-13R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Portable Hardness TesterFor cast/rough surface parts
PHT-1750
-
Loaded with features, this economically priced portable hardness tester is capable of measuring the surface hardness of a broad variety of metals on flat and round surfaces. This portable hardness tester comes complete with the G impact device, calibrated test block and rugged carry case.
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
Surface And Subsurface EW System Tester
MS 1119
-
CPCI Based BTA is used to test ECM System Processor (80386 & 8051) Boards. This system consists of a Single Board Computer (SBC), CPCI RS422 Communication and Bus Interface Board (CBI), CPCI Digital Input & Output (DIO) Board and CPCI Analog Input & Output (AIO) Board to provide the necessary input/output signals to/from the board to be tested.
-
Product
【Resistive Touch】15" (4:3) Modular Front Display Design Compatible With TPC-Bxxx Series
FPM-D15T-RE
-
300 cd/m² luminance with 1024 x 768 resolutionHigh durability and performance with industrial-Grade LED LCD5-Wire resistive touch technologyIP66-rated front panel and panel mount supportUser-friendly system status LED indicators
-
Product
Live Line Clamp Insulation Resistance Tester
MLIT-1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy and convenient live line insulation measurements for servo motor,inverter motor and power line.・More than 0.1MΩ for power line.・More than 10MΩ for servo motor and equipment.
-
Product
Winding Resistance Meter 15Amps, 2 Channels Rack
WR14R
-
Raytech Digital Winding Resistance meter WR14 R is the rack mount version of the WR14. They are designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Digital Surface Profile Gauge
NOVOTEST SP-1M
-
Digital Surface Profile Gauge NOVOTEST SP-1M is designed for profile measuring on either flat or curved surfaces. Also it can be used for measurements of surface roughness (Rz), after abrasive blasting pre-painting work.
-
Product
ITO Sheet Resistance Standards (ITOSRS)
-
Indium Tin Oxide Sheet Resistance Standards (ITOSRS) from VLSI Standards are NIST-traceable products, intended for calibration of both contact and non-contact sheet resistance measurement tools used in the LCD, flat panel and touch-screen markets.
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
Digital Low Resistance Tester
TH2512
-
Shenzhen Chuangxin Instruments Co., Ltd.
The TH2512 series digital dc low resistance tester i s an intelligent, wide range, high-precision tester which suitable for transformer, inductor copper resistance, relay contact resistance, switches, connectors, wire resistance, contact resistance component solder contact resistance, PCB line, welding hole resistance and metal detection, etc. It’s applied to the production line and can use HANDLER interface and GPIB interface (option) output good/bad signal, in order to improve production line automation testing capability.
-
Product
Air and Water Permeabilityin Concrete Both At and Below the Surface
Poroscope
-
Poroscope Plus measures the time it takes for air to flow into a known volume of a sealed, evacuated chamber in the concrete. While the vacuum reduces from -55 Kpa to -50 Kpa, a measure of air permeability is determined. For water permeability, Poroscope Plus uses the same chamber filled with water, and measures the total time in seconds for a volume of 0.01 ml of water to escape.
-
Product
15" XGA Industrial Monitors With Resistive Touch Control, Direct HDMI, DP, And VGA Ports
FPM-215
-
15" XGA TFT LED LCD with 70,000 backlight lifetimeDirect HDMI, DP and VGA input interfacesAnti-glare screen with tempered glassRobust system with Die-casting aluminum chassis and IP66-rated aluminum alloy front bezelLockable I/O connectorsSlim design enables easy installationSupports various mount options: panel, desktop, and VESA arm
-
Product
Winding Resistance Meter 100Amps, 3 Channels
WR100-13R
-
Raytech Digital Winding Resistance meter WR100-13R is the enhanced version winding resistance system with a most advanced demagnetizing circuit as a rack version. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
Resistance Welding
-
Resistance welding is a method in which the welding works are heated by resistance heat generated by sandwiching the welding workpieces with welding electrodes, passing current through them, and the metal is welded while pressurizing the works.A resistance welding machine composed of welding power supply, a weld head and an electrode. The welding power supply controls a welding current,the weld head exerts a pressure on the material to weld and the electrode provides welding current and pressurization force to the part under welding. We have been providing various kinds of welding power supplies and welding heads to meet these requirements.
