Parallel Digital Interfaces
-
Product
Digital I/O
Digital I/O Module
ADLINK digital I/O cards feature TTL I/O, isolated I/O, relay output, and timer/counter, and supports up to 256-CH high-density on a single board, making them suitable for I/O status monitoring and ON/OFF control applications.
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-02
Digitizer
he NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
NI-9478 , 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-02
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide … customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
PXIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4X.4470-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
PXI Digital Waveform Instrument
Digital Waveform
PXI Digital Waveform Instruments feature up to 32 channels, can sample and generate digital waveforms at up to 200 MHz, and interface with various standard TTL and low-voltage differential signals (LVDS), as well as settable voltage levels. These devices offer per clock cycle, per channel bidirectional control, and phase shifting. They include deep onboard memory with triggering and pattern sequencing. Some models also support doubledatarate (DDR) technology and real-time hardware data comparison. You can use Digital Waveform Devices to create device simulation and complex stimulusresponse tests.
-
Product
Network Interface Card
NIC10GBT
Interface Card
The NIC10GBT is a dual port 10GBase-T XMC module that brings 10GbE expandability to new and existing embedded systems with available XMC slots.
-
Product
2U Through 6U Customized RF Interface Unit
1257A-C
Interface
The Astronics 1257A-C is a sixth-generation RFIU tailored to your specifications. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including 2U through 6U configurations.
-
Product
*C Series CAN Interface Module
CAN Interface
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Handheld Digital Multimeter, 4 digit, with IP 67
U1242C
Digital Multimeter
The strong and solid U1240C Series handheld digital multimeters(DMMs) are the tools technicians or industrial test engineers use to perform their work confidently and efficiently. Designed for handheld users working in various environments, the U1240C series is certified to IP 67 and capable to withstand up to 3-meter (10 feet) drop to suit harsh working environments. The U1240C handheld DMM scan even work longer for you with up to 400 hours of battery life. With the built-in LED flashlight, the U1240Chandheld DMM sallow users to single-handedly illuminate test area.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 48 Channels
DN6.593-48
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Digital I/O Board
3512
Digital I/O
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
CAN Interface Device
CAN Interface
CAN Interface Devices communicate using onboard transceivers for High-Speed/Flexible Data-Rate, Low-Speed/Fault-Tolerant, and/or Single-Wire CAN as well as any external transceiver. Using the NI-XNET driver, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. You can also import, edit, and use signals from Fieldbus Exchange Format (FIBEX) and Database Container (DBC) files in integrated CAN databases. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time.
-
Product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Digitizer
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
Product
1 Meter Long SCSI Cable with 100 Pin Connector
U2903A
Digital Cable
The Keysight U2903A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2903A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 5 Channels, 2.5 GS/s on 10 Channels, 1.25 GS/s on 20 Channels
DN6.225-20
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
Digital / Synchro Converter
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
Product
MIL-STD-1553 & ARINC XMC Interface For SBCs, VPX, VME, CPCI/PXI Systems
XMC-MA4
Interface Module
The XMC-MA4’s BC capability includes variable message/label framing/subframing with transmission scheduling provides the most advanced control operations. ARINC TX has complete frequency control per channel. RT and ARINC RX, Monitor, Playback and Signal Generator functions also include industry leading functions to meet the most demanding requirements.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5960-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
High-Speed A/D 8-Bit Digitizers
Digitizer
GaGe 8-bit resolution digitizer models divide the input voltage range into 256 different digitization levels with sampling rates at up to 4 GigaSamples per second on 1 channel or 2 GigaSamples per second on 2 channels with input bandwidths of up to 1.5 GHz, deep onboard sample memory up to 16 GS (16 GB), and true ENOBs of up to 7.6 bits.
-
Product
32-CH Sourcing Type Digital Ouput EtherCAT Module
EPS-2032
Digital Output Module
*32-CH sourcing type digital output*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range*: -20°C - 60°CCompact size: 100 (L) x 100 (H) mm
-
Product
PCIe 16 Bit High Speed Digitizer - 250 MS/s on 4 Channels
M4I.4421-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Interface
RCNIC-A2PAX
Interface
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
1.6 GSPS, 14-bit Time-domain Digitizer
ADQ1600TD
Digitizer
The ADQ1600TD is a world-leading 14 bit digitizer optimized for time-domain pulse capture. With its unique 1600 MSPS capture rate, enabled by SP Devices’ ADC interleaving technology ADX, the ADQ1600TD opens for demanding measurements such as time-domain pulse capture and high-speed data recording.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.442-24
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
3U OpenVPX Sensor Interface Unit
SIU34
Sensor Interface Unit
The SIU34 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU34 leverages NAI’s 3U OpenVPX™ boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
