Parallel Interfaces
See Also: SCSI, Serial Interfaces
-
Product
NI-9860, 2-Port, C Series Vehicle Multiprotocol Interface Module
783703-03
Interface Module
2-Port, C Series Vehicle Multiprotocol Interface Module - The NI‑9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI‑XNET platform, the NI‑9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while taking other data acquisition measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO chassis.
-
Product
PXIe-1486, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO FPD-Link™ Interface Module
787454-01
Interface
The PXIe-1486 combines the Texas Instruments Flat Panel Display Link™ (FPD-Link™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1486 makes use of a combination of FPD-Link™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable FPD-Link™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the FPD-Link™ channels. The PXIe-1486 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). FPD-Link is a trademark of Texas Instruments.
-
Product
PXIe-8521, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module
786771-01
Ethernet Interface
PXIe, 4-Port, 100BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8521 is a 100BASE-T1 unshielded twisted pair (UTP) Automotive Ethernet interface for developing applications with the NI‑XNET driver. The PXIe-8521 is ideal for developing applications that require … Automotive Ethernet to test and validate automotive electronic control units (ECUs). The interface provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, which allows it to synchronize with an external network as well as the rest of a PXI system. The PXIe-8521 also provides LEDs on the front panel so that you can monitor the network link and activity.
-
Product
Enhanced Serial Interface Module for Excalibur 8000 Family of Carrier Boards, with High Baud Rate & High Throughput
M8KSerial
Serial Interface
The M8KSerial is an enhanced serial interface module for the multiprotocol Excalibur 8000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to two independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M8KSerial module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 8000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M8KSerial module is supplied with C drivers, including source code.
-
Product
Flight-Certifiable Avionics Interface
RAR15XC
Interface
The RAR15XC flight-certifiable avionics communications board delivers high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O. Its small XMC mezzanine form factor is easily integrated onto other compatible boards, like the SBC314C flight-certifiable single board computer.
-
Product
PXIe-8238, 10 Gigabit PXI Ethernet Interface Module
784976-01
Ethernet Interface
10 Gigabit PXI Ethernet Interface Module—The PXIe-8238 is a high-performance 10-Gigabit ethernet SFP+ interface for PXI Express based on the Intel 82599 10Gb ethernet controller. It includes two 10-Gigabit ethernet SFP+ ports in a single-slot PXI Express module and is compatible with both copper and fiber optic cabling.
-
Product
CAN/FlexRay/Differential Bus PXI Fault Insertion Switch - 8 Channel
40-200-008
CAN Interface
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
4x 3U OpenVPX MOSA Actuator Interface Unit
SIU34-AIUVARM-01
Actuator Interface Unit
SIU34-AIUVARM-01 is a Modular Open Systems Approach (MOSA) DO-178C & DO-254 Certifiable Actuator Interface Units (AIU) with low power high performance OpenVPX Xilinx UltraScale+ SBC with Quad Core ARM Cortex -A53, 8 GB DDR4 SDRAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet, USB 3.0, FIPS-140-3 Level 3 Cyber Security, and Single Event Upset support.
-
Product
PXIe-6593, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument
785976-01
Serial Interface
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
3U OpenVPX Sensor Interface Unit - SIU36
SIU36
Sensor Interface Unit
The SIU36 is a highly configurable rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, communications, Ethernet switching and processing. The SIU36 leverages NAI’s 3U boards to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
3U OpenVPX Sensor Interface Unit
SIU32S
Sensor Interface Unit
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
PXI Express Interface
EMX-2500
Interface
The EMX-2500 is the industry’s first gigabit Ethernet LXI based PXI Express interface. This combines Ethernet's widespread usage and robust architecture with instrumentation-specific functionality, such as wired trigger bus and IEEE-1588-2008 synchronization, and extends it for use in PXI Express mainframes, making it an ideal solution for data acquisition applications.
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Interface
RCNIC-A2PAX
Interface
The RCNIC platform is a high performance, PCI module (PMC on carrier card) for the AFDX / ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation.
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
LIN Interface Module
C- Series
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
PCIe-8244, 4-Port, USB3 Vision Frame Grabber Device
782890-01
Interface
The PCIe‑8244 is a USB 3.0 interface device designed for use with USB3 Vision cameras. USB 3.0 is ideal for high-data-rate machine vision applications. USB3 Vision cameras also offer plug‑and‑play functionality and ease of use through a standardized catalog of functions.
-
Product
10-Ch Pneumatics Selftest Module
YAV90PNT
CAN Interface
Use this module in your self test diagnostics fixture. The YAV90PNT can be used as counterpart of the YAV90PNE, to test that is working properly.
-
Product
MIL-STD-1553 CompactPCI Interface Card
CPCIC3/6-1553-PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
PXI-8360, MXI-Express Interface, PXI Remote Control Module
779501-01
Interface
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.
-
Product
PCI-8517, 2-Port FlexRay Interface Device
780685-02
Interface
2-Port FlexRay Interface Device—The PCI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PCI‑8517 contains two fully functional FlexRay interfaces, allowing an individual engine control unit (ECU) to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
Interface Board, 8:1 USB
40-965-903
Interface
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
Product
PXI Ethernet Interface Module
Ethernet Interface
The PXI Ethernet Interface Module equips PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, this module is ideal for high-performance data transfer and vision applications on the PXI platform. Additionally, the PXI Ethernet Interface Module has independent bandwidth to support up to four GigE Vision cameras without PoE.
-
Product
Thunderbolt Interface
NLINE-T1553
USB Interface
Supports Full Real-Time Control the Same as a PCI Express Card in a Server! Much Better than a non-real-time USB.Full Hardware Interrupt Handler Support! AltaAPI SDK Provides Easy Integration – Use the exact same code as other Alta PCIe devices! Windows 10 Support Only
-
Product
20 GHz Differential Probe with ProLink Interface
DH20-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
Interface Card
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
Serial Interface
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Interface
RAR-cPCI
Interface
Available in a range of configurations to match your needs, the RAR-cPCI provides complete, integrated databus functionality for ARINC 429, ARINC 575 and selected 2-wire, 32-bit protocols in a CompactPCI form factor.
-
Product
Interface Module for the Multimode, Muliprotocol Excalibur 8000 Family Carrier Boards
M8K1553MCH
Interface Module
The M8K1553MCH interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M8K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M8K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
