T-rays
-
product
ATR Tray 3/4 long
TATR-BL-S
The ATR Tray is shock isolated to meet ARINC 404A via four mounting points. The trays are standardized so that any enclosure designed to meet the ARINC 404A specification will securely fit. Guide pins allow ease for blind-mating insertion.
-
product
Type 15, CompactPCI Serial, 9 Slots, SSL, 4U, 63HP, 294mm
047-711
CompactPCI Serial System Type 15 with 9 Slots: 8x CompactPCI-S.0. Peripheral Slots and 1x CompactPCI-S.0. System Slot on the left side of the system platform. 2x 300W pluggable, air-cooled mit fan tray and powder coated.
-
product
ICE 3000 Series
ICE3001
This subsystem is an agile filter for the SATCOM frequency band, capable of acting as either a receive or a transmit filter. It enables simultaneous operation of multiple transceivers in extreme cosite environments. The ICE3001 provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals for either receive or transmit applications. This filter is a highly integrated design incorporating complete Built-in-Test capability. The design has been qualified for military applications. A dual-mount tray is also available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3001.
-
product
Automated Programmer Superpro Sb05
※ Four Pick & Place nozzles, Eight socket pressing actuators and 2 tape feeders※ High throughput up to 2400UPH※ Embeded with eight ultra-high speed programmers SuperPro / 7500, each with up to 4 sockets, totally 32 sockets. Throughput 60 times higher than SuperPro / SB01 for eMMC devices※ Supports over 80,000 devices from over 300 IC manufacturers※ Supports tray, tape and tube input and output. Supports laser and ink marking※ Short change-over time※ Intelligent s/w cuts learning curve and setup time, makes task management an easy job※ Compact sizeHigh throughput：4 nozzles, 8 independent socket pressing actuators and 2 tape feeders. Up to 2400 UPH for devices with programming time less than 50 sec. Throughput 0.6 to 60 times higher than SuperPro/SB01, especially higher for large capacity devices like eMMC, NAND /NOR FLASH,SPI FLASH. Suitable for both small and large capacity devices. Prog. Time (S) 50 60 120 180 240 300 UPH (unit per hours) 1600 1600 840 560 420 336 Accurate positioning：Equipped with high performance servo system, precise CCD cameras and vision algorithm for device alignment and sockets / pick & place spots positioning.High performance programmers： 8 ultra-high speed universal gang programmers SuperPro/7500 resident. Each with up to 4 sockets, totally up to 32 sockets in the system. Supports up to 100,000 devices from over 300 IC manufacturers and growing.Varied I/O devices：Supports tray, tape and tube input and output. Supports laser and ink marking. Supports packing conversion and can work as a packing conversion machine alone.Short change-over time：I/O devices and socket adaptor are easy to be changed when programming task need to be changed. Socket positioning can be performed automatically. Projects can be loaded automatically with barcode scanning.Powerful and intelligent software：Setup data saved for next operation, log file and statistic reports for quality and yield traceability, flexible sockets prohibition strategy promises high yield rate for unattended operation, graphical user interface cuts learning curve, prevents chip over-lapping by socket checking before chip placing.Remote Control：Remote project loading, quality monitoring, volume control, file security.
-
product
3-Fans 19" Rackmount Fan Tray
FTA-319
3-fans 19" rackmount fan tray delivers 318 CFM of cooling for your rackmount equipment
-
product
Automatic Battery/Electrical System Tester w/Cart
6044C
• Same features as the 6044 • PLUS heavy duty, two-wheel tilt-back cart with 8” wheels and 2 trays• Made in USA of US and Global Components
-
product
Flexible Pick And Place Machine With 128-feeder Capacity
MC385V2V
The high-precision MC385V2V Pick and Place system ensures accuracy and repeatablity with high-quality ballscrew drive, linear encoders, and full vision alignment. Programming and operation are made easy with mature, fully supported Windows-based software. Machine holds up to four 32-port feeder racks for a maximum feeder capacity of 128 tapes. Waffle trays and cut strip tape holders can be used in the placement area.
-
product
HJT Tray Automation
JRT Photovoltaics GmbH & Co. KG
The highly sophisticated machine platform HJT TRAY AUTOMATION ensures the fully automated loading and unloading of trays for inline-coating processes. Outstanding innovation is the particularly surface-friendly, yet high-performance handling of wafers in inline flat-carrier transport. This involves high-precision, row-by-row positioning of the wafers which are individually measured.
-
product
TO-CAN Package Inspection System
7925
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
product
19"x9U Enclosure
Pixie-16 Crate
The Pixie-16 PCIe Crate is a 19” x 9U enclosure to house up to 13 XIA Pixie-16 modules, featuring a removable fan tray and power supply.
-
product
Rack Rail Kit For M9010A, M9018B, And M9019A
Y1217A
Includes support rails and attachment hardware; can be used with both the rackmount kit and the cable tray kit
-
product
Eurocard Based Systems
With over 100K Rittal brand components, Pixus has virtually unlimited configurations of chassis platforms for embedded computing. Typical plug-in modules are 3U or 6U with a 160mm depth. OpenVPX, CompactPCI Serial, CompactPCI, VME, and VME64x are open standard backplane architectures commonly used in 19" rack-mount Eurocard enclosure systems. (For OpenVPX products, see the Pixus OpenVPX section.) Enclosures are available to hold these boards in front-to-rear, bottom-to-top, and for 6U and 8U boards there is side-to-side cooling options. The chassis can come with or without integrated fan trays or with redundant push-pull cooling. EMC versions are also standard.
-
-
product
Rugged Deployable CMFF Chassis Aligned To SOSA™ With SAVE Tray
ATRSAV07BRN1HVQE4
CMOSS Modular Form Factor (CMFF) field-deployable chassis, with a tray compliant with the Standard A-Kit Envelope (SAVE). Includes a 7 slot 3U VPX backplane, chassis manager, and VITA 62 plug-in power supply. it is aligned with the SOSA™ Technical Standard and designed for C5ISR, EW and EO/IR applications. Meets MIL-STDs for shock, vibration, and other environmental standards.
-
product
9-fans 19" rackmount fan tray
FTA-919
9-fans 19" rackmount fan tray delivers 954 CFM of cooling for your rackmount equipment.
-
product
MSP-Series Screw Presenters
The MSP is a small, tabletop screw presenters used to organize and automate work areas and production cells. Screw presenters make assemblers and the assembly process more efficient by mechanically presenting a screw to a fixed pick up point. Conventional assembly methods cause assemblers to inefficiently fumble with screws that are stored in bins or shaker trays. The enhancement of productivity is estimated to improve assembly time by nearly fifty percent. The inexpensive screw presenter is an alternative tool instead of the cumbersome and very expensive screwfeeder systems.
-
product
Miniature Two-Point Probe Set
PRF-922B
The PRF-922B Miniature Two Point probe accurately measures point-to-point resistance of small areas. Like Prostat's PRF-912B Miniature Concentric Ring, the PRF-922B is capable of measurements up to 1.0x1012 ohms. Built-in distance stops provide consistent electrode to sample pressure for developing repeatable measurements. Use the PRF-922B to measure small material samples, hard to assess molded areas, edges of parts, tray or tape cells and other very small objects and surfaces. The assembly is supplied with replaceable conductive electrode covers to enhance contact resistance on irregular surfaces and composition materials. Thus, measurements may be made with either the gold plated electrode contacts, or via conductive rubber covers.
-
product
Labelling Systems
8000BL
The Model 8000BL is a high volume labelling system for tray-borne devices. Equipped with tray stackers and a Zebra 90XiII label printer, the 8000BL can apply labels safely, accurately and quickly to BGAs, QFPs, TSOPs, PGAs, etc.
-
product
VME Load Card
WIENER VME load boards are designed to test VME crate power supplies and fan trays by drawing power from the VME backplane and dissipating it as heat. A series of switches on the module front panel allows for easy adjustment of the current draw for each voltage channel.
-
product
ICE 3000 Series
ICE3005
The ICE3005 is an agile filter/amplifier cascade for the UHF frequency band with a VHF bypass. It enables simultaneous operation of multiple transceivers in a cosite environment and is factory configured for an ARC-210 interface. This filter/amplifier provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals while still providing full output power in transmit mode and excellent selectivity to interfering signals at the transceiver’s RF input in receive mode. All transmit, receive, and bypass switching is incorporated into the two-port design. The ICE3005 also includes a separate audio processor circuit that mitigates popping and drop-outs in the R/T audio that are common in hopping or blanked waveforms. The ICE3005 incorporates extensive Built-in-Test capability and is qualified for military applications. A mounting tray is available for easy incorporation on your platform. Cost-effective modifications are available on the ICE3005. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
product
VPX Chassis 4U/50HP 7 Slots
BKP3-CEN07-15.2.3-4
his 7 slot Hartmann Open VPX BKP3-CEN07-15.2.3-4 profile system chassis provides an intelligent, practical packaging solution for high-performance processors. The 50HP wide, rack-mountable enclosure for vertical mounting of boards is outfitted with a 600W plug-in power supply and a 1U removable, bottom mount fan tray.
-
product
Flexible Pick And Place Machine With 128-feeder Capacity
MC385V1V
The high-precision MC385V1V Pick and Place system ensures accuracy and repeatablity with high-quality ballscrew drive, linear encoders, and full vision alignment. Programming and operation are made easy with mature, fully supported Windows-based software. Machine holds up to four 32-port feeder racks for a maximum feeder capacity of 128 tapes. Waffle trays and cut strip tape holders can be used in the placement area.
-
product
Fiber Optical Switch Tray To 16x16 Ports
SERIES 6000 MULTIMODE
The Series 6000 Multimode switch is designed to meet the needs of the most demanding component, subsystem and system test applications. All-optical switching allows test equipment connections to be fully automated and controlled remotely 24/7 via software from virtually anywhere in the world.
-
product
3U PXIe Chassis
6025
The new W-IE-NE-R PXIe 6025 series provides a fully redundant and front accessible chassis solution for performance critical applications. Built as a 19” rack-mount chassis with 7U height and low depth the chassis is outfitted with an 8 slot PXIe hybrid backplane from Hartmann Electronic. A redundant power supply design as well as cooling fan tray guarantees highest reliability & availability.
-
product
ATCA 7U 14 Slot dual star
109ATCA714-000XR
The Elma Electronic 5U ATCA Dual Star backplanes feature pluggability and redundancy "everywhere". There are pluggable connectors for fan trays, shelf managers, and power entry modules.
-
product
Carousel Autosamplers
The carousel platform is designed to be sturdy, reliable, and easy to use. The rotating sample tray minimizes space requirements, making it easy to fit into an existing housing. It holds up to 96 samples when fully loaded and contains a microprocessor that allows sequential or random sampling. The autosampler is typically interfaced to and controlled by the host instrument computer using a serial, USB, or IEEE-488 parallel communications cable.
-
product
Passive Component Storage Module Series
TrayPXIe
The TrayPXIe is an accessory tray that stores your fragile passive fiber optic components such as splitters, connector adaptor patchcords, WDM couplers, and isolators in one handy module in the PXI chassis.
-
product
Warpage Metrology System
TableTop Shadow Moiré (TTSM)
Measure warpage of substrates up to 300mm x 310 mm (a 300mm wafer or two JEDEC trays) with the entire measurement taking less than two seconds. Whether individual parts or a JEDEC tray of multiple parts, the TTSM provides an ultra-fast and highly accurate measurement at room temperature that is suited for tabletop use.
-
product
Multi-Wavelength Planar Lightwave Circuit Splitter (PLC Splitter)
PLC-1 × 口口口
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai Planar Optical Waveguide Optical Splitter (PLC Splitter) is an integration waveguide optical power distribution device that based on quartz substrate, featured with small size, wide working wavelength range, high reliability and excellent uniformity of optical split, etc. It is especially suitable for connecting local unit with terminal unit in passive optical network (EPON, BPON, GPON, etc.) to achieve optical signal splitting. The main design divide optical signal in optical communication system into multi-way output. The component that we manufactured is with high stability to light source and temperature. And diversified packages can meet customers’ different requirements in application. According to the various requirements, our PLC splitter is with various types: bare fiber type, miniature type, fan-out type, module type, tray type, plug-in type , Blade package type, rack-mounted type, etc.
-
product
Powered NIM Crate
NIM 6000 Series
The WIENER NIM 6000 series combines the technical advantages of the VME 6000 high efficient , low noise switching power supplies with the high reliability CERN spec. conform WIENER NIM chassis. The modular concept of WIENER NIM 6000 series crates allows fan trays and power supplies to be easily inserted and removed without tools.
