Electrodes
-
Product
Proving Unit & Voltage Tester Kit
DLPK1
-
Touch electrode for Quick testing of fused leads Optical and acoustic continuity Indication Low battery indication A portable, battery powered Proving Unit for testing Two Pole Voltage Testers up to 690V Continuity Tester for testing: Fuses, Fused test leads etc
-
Product
Miniature Concentric Ring Set
PRF-912B
-
- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Flexible Screen-Printed Electrode Strip
SPE1
-
A disposable screen-printed electrode (SPE) for electrochemical sensing, laboratory analysis, and biosensor research, providing reliable performance, excellent reproducibility, and plug-and-play operation.
-
Product
Bottom Electrode SMD Test Fixture
16197A
Test Fixture
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
Product
Battery Boxes Testing Equipment
-
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
Product
Platinum Sheet Electrode
PT1
-
High-purity platinum sheet electrode (99.99%) with PTFE insulation housing for reliable electrochemical measurements. Suitable for electrolysis, electrocatalysis, fuel cell testing, corrosion studies, and general laboratory research.
-
Product
Liquid Test Fixture
16452A
Test Fixture
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
Product
Double Sheet / Splice Inspection
-
Leuze electronic GmbH + Co. KG
Double-sheet control sensors enable the reliable differentiation between one or more layers of very thin objects made of different materials. This allows, for example, single-layer paper sheets to be reliably pulled in or individual electrodes to be stacked for the production of a battery cell. Different operating principles, based on ultrasonics and capacitive sensors, cover the range of materials for different applications. Sensors for splice inspection detect desired and random splices in paper webs independent of the surface color and material properties.
-
Product
Ion/pH/mV Meter with Single Junction pH Electrode
Ion 6+
-
Direct Ion Concentration for use with most mono- or di-valent Ion Selective Electrodes (ISE) :: mV measurement mode allows you to check performance and calibration of your ISE
-
Product
Micro Single-Channel Interdigitated Electrode Chip
MSI1
-
Single-channel IDE chip for MEMS, optical sensing, gas sensing, biosensing, and electrochemical research. Designed for reproducible electrochemical measurements with customizable electrode gaps and layouts.
-
Product
9VT Neon Tube Tester
-
West Coast Custom Designs, LLC
When the antenna and/or the Disc are touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate.
-
Product
Platinum Interdigitated Electrode On Quartz
RIE1
-
Quartz-based platinum IDE for gas sensing, biosensing, MEMS, photoelectric, and electrochemical applications.
-
Product
Earth Leakage Relay
-
Nippen Electrical Instruments Co.
NIPPEN's Earth Resistance Testers are used for measuring earth electrode resistance, soil resistance, earth continuity, neutral and earth loop resistance, resistance of various components etc.They are used in Railways, Defence, Utilities, Power Plants, Geological Surveys and other Industries.Direct reading type models SET/DET/TET provide direct readings of resistance on moving coil type meters, having a linear scale, 70mm long knife edge pointer and an external zero adjustment.
-
Product
Corrosion Analysis
Profometer Corrosion
-
The Profometer Corrosion is the most versatile corrosion analysis solution in the market based on the half-cell method. Proceq’s unique wheel electrodes allow the fastest and most efficient on-site testing. As direct successor to the Canin, it is compatible with existing Canin and most third party electrodes.
-
Product
5μm Transparent Quartz Interdigitated Electrode Chip
TIF1
-
5μm transparent quartz IDE chip designed for MEMS, biosensing, gas sensing, electrochemical, and photoelectric applications.
-
Product
pH / mV Transmitter
DO9403T-R1
-
The DO9403T-R1 pH transmitter converts the output of a pH electrode, with temperature compensation, into a 4÷20 mA signal.
-
Product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
-
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
Product
10μm Quartz Interdigitated Electrode Chip
BAP1
-
Transparent quartz IDE chip with a 10μm gap for gas sensing, biosensing, and photoelectric applications.
-
Product
Pocket Water Quality Meters
LAQUAtwin Ca-11
-
HORIBA's unique compact meter integrates the electrode, display and sample container to enable simple, effective on-site testing by direct measurement from a single drop.
-
Product
Microscopic Four-Point Probes
M4PP
-
CAPRES M4PP Microscopic Four-Point Probes have an electrode pitch three orders of magnitude smaller than conventional four-point probes, and are fabricated using silicon micro-fabrication technology.
-
Product
Panel Mounting Conductivity Transmitter
DO9786T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
High Voltage Thick Film Chip Resistors
HVTK (HVR)
-
*Highly reliable multilayer electrode construction*Higher component and equipment reliability*Excellent performance at high voltage*Reduced size of final equipment
-
Product
Field-installation Type Simplified Fluoride Ion Concentration Meter(Two-Wire Transmission)
HC-300F
-
HC-300F is connected to a fluoride ion electrode (1009) to detect free fluoride ions in the sample water.(Total fluorine is not detected.) It is suitable for fluoride ion monitoring in effluent from factories, e.g., those of semiconductor FPD and glass manufacturers.
-
Product
BOMBARDING A.C. MILLIAMPERES METER
-
A Bombarding A.C. Milliamperes Meter is one of the four instruments essential for proper luminous tube processing. This instrument monitors the level of bombarder current in milliamperes that is generated by the bombarder, through the tube being processed. It is necessary to accurately monitor the current for the tubing and electrode sizes used to ensure that the right amount is applied at the appropriate time. To do otherwise may cause damage to the electrodes, fluorescent coating inside the tube and adversely affect the glass structure.
-
Product
Resistivity Imaging & Sounding System
Syscal Junior Switch
-
The Syscal Junior is an all-purpose resistivity imaging and sounding system for environmental applications. The system can be supplied as a standard imaging system capable of recording two measurements simultaneously. The second recording channel significantly improves data acquisition time when the instrument is fitted with internal switching board for 24 (Switch-24) 48 (Switch-48) or 72 (Switch-72) electrodes for Electrical Resistivity Tomography (ERT).
-
Product
Conductivity Transmitter
DO9766T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
Ocean and River Instruments
RINKO W
-
Rinko W is an autonomously deployable data logger for long-term DO measurements. In order to protect the sensing foil against accumulating bio-fouling, the instrument has a mechanical wiper to sweep the optical window. The optical sensor does not have a membrane neither electrolytes, thus, it need less maintenance than electrode or galvanic sensors.
-
Product
Water Analysis Meters & Electrodes
-
Ideal for Accurate Everyday Measurements in the Laboratory
-
Product
Resistivity Meter with Multi Electrode
POLARES
-
Till this moment the use of Electrical Resistivity Tomography (ERT) for geology has always been basically the same since its debut, based on the original vertical Electrical Soundings (VES) principles: applying a continuous current to two stakes inserted into the ground and measuring the corresponding voltage between other two. The applied current and thus the relative tension have always been continuous, with an inversion in polarity for each measure. The new tool POLARES uses an alternate current, instead, sinusoidal type, with an adjustable frequency.
