-
Product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-812
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI, CPCI Development And Prototyping Board
TE2100
-
Team Solutionsí PXI Development and Prototype board is the fastest road for system integrators to deliver a PXI customized product and provides design engineers with a speedy avenue to release PXI based prototypes and products.
-
Product
Power Interface and Prototype PXI Card
GX7404
Interface
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785593-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
USRP Software Defined Radio Reconfigurable Device
-
The USRP Software Defined Radio Reconfigurable Device is built on the LabVIEW reconfigurable I/O (RIO) and universal software radio peripheral (USRP) architectures. It includes a powerful FPGA for advanced DSP that you can program with the LabVIEW FPGA Module. The device includes 2x2 MIMO transceivers or four-channel superheterodyne receivers, supporting center frequencies from 10 MHz to 6 GHz, with up to 160 MHz of instantaneous bandwidth. The USRP Software Defined Radio Reconfigurable Device also optionally includes a GPS‐disciplined oven-controlled crystal oscillator (GPSDO), which provides greater frequency accuracy than temperature- compensated crystal oscillators. Prototyping applications include LTE and 802.11 prototyping, spectrum monitoring, signals intelligence, military communications, radar, direction finding, and wireless research.
-
Product
PCI Data Acquisition Boards
-
Ultraview''s PCI data acquisition add-in cards are complete data acquisition (A/D) and control (D/A) systems on a single PCI Bus card. Ranging in speed from dual 14 and 12-bit 1-25MSPS boards up to 1500MSPS 8-bit boards with 8GB/16GB of on-board RAM. All cards come with graphical waveform viewers, example user programs (source code included) and device drivers for Linux or Solaris, allowing users to quickly prototype and develop their applications.
-
Product
Analog Simulator
MPLAB® Mindi™
-
MPLAB® Mindi™ Analog Simulator reduces circuit design time and design risk by simulating analog circuits prior to hardware prototyping. The simulation tool uses a SIMetrix/SIMPLIS simulation environment, with options to use SPICE or piecewise linear modeling, that can cover a very wide set of possible simulation needs.
-
Product
Optical Components and Instruments
-
Optical Surfaces Limited are a UK based company supplying the world with optical components and instruments. We specialise in large optics, beam expanders, collimators and prototypes, plus custom systems and optics.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786166-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Digitizer
785590-01
FlexRio Digitizer
The PXIe-5775 is a PXI FlexRIO Digitizer that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PXIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Open Frame Panel PC
-
By highly flexible configuration with a high level of modularization, ADLINK's Open Frame Panel PC, leveraging Intel® x86 and NXP ARM-Based solutions, with ready-to-use design helps system integrators, integrated solution providers, and brand vendors quickly deliver cutting-edge functions to individual HMI applications. Leveraging our unique Function Module (FM) design, these industrial panel PCs accelerate prototyping according to the application's requirements while saving considerable time, money, and effort. The SP2 series is ideal for industrial automation, transportation, retail, healthcare, gaming, and other industries.
-
Product
SparkFun Sensor Kit
-
Do you have a good understanding of various sensors or need a variety of them for a project? The SparkFun Sensor Kit includes a sensor for just about every job. With everything included in this kit, you'll be able to sense gesture, humidity, temperature, motion, touch, sound, altitude, acceleration and more! These are some of our favorite sensors from each category. But wait, there's more! The SparkFun Sensor Kit now includes several of our sensor boards that feature the Qwiic Connect System for rapid prototyping!
-
Product
Decade Box, Calibrated W/Data, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL D
-
The 72-7265 CAL D from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Doppler Radar Target Simulators
-
Automotive radar sensors play a vital role in the current development of autonomous driving. Their ability to detect objects even under adverse conditions makes them indispensable for environment-sensing tasks in autonomous vehicles. As their functional operation must be validated in-place, a fully integrated test system is required. Radar Target Simulators (RTS) are capable of executing end-of-line, over-the-air validation tests by looping back a received and afterward modified radar signal and have been incorporated into existing Vehicle-in-the-Loop (ViL) test beds before. However, the currently available ViL test beds and the RTS systems that they consist of lack the ability to generate authentic radar echoes with respect to their complexity. The paper at hand reviews the current development stage of the research as well as commercial ViL and RTS systems. Furthermore, the concept and implementation of a new test setup for the rapid prototyping and validation of ADAS functions is presented. This represents the first-ever integrated radar validation test system to comprise multiple angle-resolved radar target channels, each capable of generating multiple radar echoes. A measurement campaign that supports this claim has been conducted.
-
Product
PXI-8517, 2-Port PXI FlexRay Interface Module
780689-02
FlexRay Interface
2-Port PXI FlexRay Interface Module—The PXI‑8517 is designed for developing FlexRay applications. As part of the NI‑XNET platform, the PXI‑8517 works well in applications requiring real-time, high-speed manipulation of hundreds of FlexRay frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The PXI‑8517 contains two fully functional FlexRay interfaces, allowing an individual ECU to be connected to the interface when other cold-start nodes are not available. You also can use the interfaces individually to connect two separate FlexRay networks while maintaining full performance on each interface.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Decoders
LokSound
-
Electronic Solutions ULM GmbH & Co. KG
With the LokSound family decoders we offer all model railroaders who want the utmost of authenticity on their layout, a real highlight. With LokSound , the excellent features of ESU-decoders are even more enhanced by the addition of sound functions. Its sounds simple, but “wow”: In the future, your locos not only run like the prototype, they sound exactly like it! That’s made possible through our award-winning LokSound technology- the reference for good sound on the layout since its introduction in 1999. By the inventor. By ESU. LokSound decoders are available for various applications, depending on gauge or digital system.
-
Product
60 GHz Development System
PEM009
-
The Pasternack / Vubiq 60 GHz development system provides rapid evaluation of Pasternack’s 60 GHz waveguide modules for quick prototyping for millimeter wave wireless system development. This high speed wireless 60 GHz developer kit is created from a partnership between Pasternack and Vubiq (pronounced “View-bik”), an industry expert in designing 60 GHz RF systems. Our 60 GHz wireless development systems make it easy to design new products and applications in the emerging unlicensed millimeter wave ISM V band.
-
Product
HighFfrequency Test Devices
-
VI Systems now releases engineering prototype samples of high performance transmitter and receiver optical subassemblies (TOSAs and ROSAs) for 25 Gbit/s and 40 Gbit/s applications and product development.
-
Product
PXI Prototyping Module, 1-Slot, 37-Pin D-Type
40-225A-201
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
LIN Interface Device
LIN Interface
LIN Interface Devices are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. LIN Interface Devices work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
Sensors
-
Electronic Product Test & Design
Development kit has ideal support for software development, prototyping and depth-sensing evaluation.
-
Product
Flying Probe Tester
Condor MTS 505
-
Primarily the Flying Probe Tester was developed to enable In-Circuit testing (ICT) of prototype PCBs. For testing a new design an existing fixture has to be changed or a new fixture has to be procured. The fixtureless design of the MTS 505 Condor is one of its most attractive properties, where the unnecessary and costly time delays incurred for fixture build or changes can be avoided. It is the ideal platform for testing prototypes.
-
Product
RF Prototyping Kit
VXI-5501
-
* VXI-5501 has a Bare Copper-clad Prototyping Board for RF and microwave modules.* Includes a VXI-5524 Register Based Interface Board with 48 digital IO lines and a 16-bit VXI data bus.* User configurable model number, manufacturer ID, version and serial numbers identifies the module as from your company.* Includes a blank front panel, side shields, manual, layout aids and VXI-Kit hardware for a single slot wide C-size module.
-
Product
Dual Gate LCU
-
Abaco Systems’ Dual Gate local control unit (LCU) provides an ideal user interface for the ADEPT line of automatic video trackers and can be used in a prototyping, development or production project phase.
-
Product
Boundary Scan Test
-
Boundary Scan is a very useful tool for quick, low-cost, re-usable powered-up test of an assembly for basic functionality. Because a fixture with test probes is not required, it is possible to have a working test available within hours or days, rather than weeks. Designers can receive rapid feedback on their prototype boards with tests that can be used again during production testing, as well as for device programming. Given power, ground and Tap port signals, tests can be written to assess the performance of the boundary scan enabled parts on an assembly and other parts on the boundary scan chain.
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
LIN Interface
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI Prototyping and Breadboard Modules
-
The breadboard modules with digital I/O (the 40-220A series) allow the user to construct their own circuit in situations where a PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include creating custom circuitry that can be housed on a 3U board or to build special “one-off” switching modules.
-
Product
PXIe-5763 , 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785160-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
