Wire
See Also: Contacts, Harness, Connectors
-
product
Circuit Testing
Tester, Circuit GFI
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
product
Wire Harness Tester
Panther4HT Master- Slave DSU
Qmax Test Technologies Pvt. Ltd.
The Master- Slave DSU based Panther4HT Wire Harness tester is designed for testing and verifying electrical connections in a cable, harness, backplane or any other wired assembly. It offers unique Qmax MASTER - Slave concept and SATELLITE UNIT Options to avoid looping back of cable to the ATE. All Satellite Units communicates the measurements through LAN interface which is very useful for on-board applications in Aircrafts / Ships and similar applications where large cable looms are used. This innovative concept will eliminate the long adapter cables and hence storing, maintaining and re work of these kind of cables are avoided. Furthermore single Master Controller Unit (MCU) is used to control not only all the satellite units , but also communicate with all satellite units through Ethernet Communication port. A single reference Cable is used to link the all the satellite units with the Master Controller in controlled loop manner is a value add to the product.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Broadband Diagnostics
TruVizion
TruVizion gives you a comprehensive view into the health of your cable or DSL network, including up to 90 days of historical data.PreEqualization Analyzer lets you quickly find upstream impairments like reverse splitters, loose or corroded connectors and bad wiring. Plus, you can be proactive and actually fix those problems before they affect service for your subscribers.RF Inspector is an inexpensive app that can do what a meter can do, except it can do it on a tablet from wherever you happen to have Internet access. That means in the office, at home, or in the field.Upstream Analyzer shows you the RF signals for all ports and modems on your Cisco CMTS without any additional equipment, cabling or connectors, and yes, you can see ingress under the carrier with one click.
-
product
LAN (PoE) Expansion Kit (supporting Gbit Ethernet)
OP-SB89G
OP-SB89G is an expansion board for Ethernet LAN (supporting Gbit), inserting into a slot of portable communication analyzer (LE-8200A/LE-8200). It is a stand-alone LAN analyzer, exchanging the measurement board and line state sheet for LAN signals. The monitor function measures data at real time by simply connecting the LAN cables. The packet generation function transmits frames from the analyzer at wire rate.
-
product
Wire Harness Tester
NX Solo
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
-
product
Low Cost Precision Shunt
LPS
This is a precision metal clad resistor designed with four terminals. These models exhibit a high load capacity as well as excellent accuracy. The isolated voltage and current connections make them suitable for very precise current measurements. Direct attachment to current bus and connection to voltage using flexible wires enables easy current measurement.
-
product
Temperature Transmitters
Conversion of Thermocouple, RTD, millivolt and resistance signals from field sensors is accomplished using DEVAR two wire signal transmitters.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Cut Ends, 0.5m, HV
A037DF4-C-HA050
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Square Post for Wire Wrap with Anti-Rotation
610138122
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
PCB Connectors
CMD Series
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Cut Ends, 1m
40-972-068-1m-MU
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
product
LXI WTB Adaptor, Terminated
60-982-002
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
192 X 4 / Dual 96 X 4, cPCI High Density Matrix Module
DP-cPCI-4149
Matrix switches are the most versatile type of switching system. Any input can be connected to any output, singly or in combination. A matrix switch simplifies the signal routing in an overall system, through reduced internal connection path.DP-cPCI-4149 offers ultra high density matrix in a single slot 6U sized cPCI module with flexibility to configure in the following ways:192 x 4 (Single- wire).Dual 96 x 4 (Single -wire).96 x 4 (Two-wire)DP-cPCI-4149 uses magnetically screened reed relays.
-
product
Receiver, 9050, 50 Module, Dual Discrete Wiring Tiers
310104368
The 50 Module Receiver is a rugged system devised to accommodate high I/O. With high contact point availability, the 50 Module Receiver is suited for larger test and measurement systems. Both tiers are designed for discrete wiring, and can accommodate individual 9025 ITAs.
-
product
Heavy Duty Ranger Mutt
TT9102
Commercial trailer light and electric brakes tester that reduces guesswork and saves time by powering each trailer electrical circuit in 7-way round pin arrangements. Allows for proper verification of wiring configuration, ground integrity, short circuit and overload conditions, along with electric brake operation and turn signal simulation.
-
product
AC DC Withstand Voltage & Insulation Tester (HI-POT)
SS71XX series
High voltage withstand and insulation tester (HI-POT tester) is used for testing insulation grade and withstanding voltage capability of electrical equipment, transformers, motor, relays, cables, electronic components, electronic applications, inductors, ignition coils, insulation wires, insulation tapes, valve coils, reactors, contactors, etc.
-
product
High Power, Low PIM Switch Unit
LPSU
Low PIM coaxial switch matrix 5 x 6 or 1 x 4 configurationFrequency range 698-2700 MHz.SCPI commands via Ethernet (wired or wireless).Significantly reduces test time for multi frequency PIM applications.Applications: ATE systems, multi-band antenna and component testing.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Unterminated, Tinned Ends, 0.5m
A025CFR-T-5A050
This 0.5m long female 25-Pin Micro-D to unterminated (with tinned ends) cable assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connector to its associated product.
-
product
LED 4 Flat Tester
48655
Hopkins Manufacturing Corporation
Quickly and easily confirm if your vehicle 4 flat connector wiring is properly installed and functional. Fits on your keychain to keep it handy! LEDs test left/right turn, brake and taillight.
-
product
GPS Wireless Clock
Signals & Systems India Private Limited
GPS Clock offers an easy, cost-effective solution for accurate, synchronized time displays without expensive, disruptive installation procedures. Because there are no wiring requirements, installation times are drastically reduced. It is ideal for renovation projects, as there is no need to worry about installation work, as well as new construction. The GPS clock can be synchronized through GPS Antenna or Wireless Antenna. The display can be wall/panel / tabletop mountable. It can be used as a wireless clock to synchronize many wireless slave clocks in and around the buildings.
-
product
Short Buddy
A tool designed for hands free electrical troubleshooting. Short Buddy uses audible beeps to help find intermittant electrical connections and wiring issues.
-
product
Tone Generator with Cable Tracer
1RA470
Cable tracer is designed to trace wires without damaging the instalations. It has wolume control to increase sensitivity. Power supply is standard 9V battery.
-
product
Mass Interconnect Solution
SCOUT
SCOUT is an innovative pull-through Mass Interconnect solution specifically designed to deliver the full performance potential of the PXI platform at the ATE interface. SCOUT, featuring DAK (Direct Access Kit) connectivity, enables system designers to limit or eliminate traditional instrument cables by replacing them with DAK connection modules that utilise PCB, flex-circuit or short wire connections.
-
product
Termination Board
MSTB 009
The MSTB 009 a-Series Analog Termination Board allows quick and secure connection of discrete wires to Data Acquisition Processors. It is the only analog termination board that may be used with the DAPs listed at the bottom of this page.
-
product
3 ft Coax Wire with a Coax Pin
GX96411
One 3 ft Coax Wire with a Coax Pin Crimped on One EndRequires the GX96409 connector housing.
-
product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
product
Desktop Type AE Systems
Compared to the online remote AE systems, desktop type AE systems are connected to and accessible within the local network, either directly by wires or via wireless local networks. Such desktop type AE detection system is normally use with a computer or laptop on a desk or table on site or near the facility. It is usually conducted and real-time controlled by professionals to accurately locate the AE ‘Hits’ sources and analyse the AE data in full aspects. There are two types of AE systems that can be used as desktop type systems, the SAEU3H multi-channel AE system and the RAEM systems respectively.
-
product
Cable, 25 Pin 1.27mm Pitch Micro-D, Female to Female, 0.5m
A025CFR-025CFR-5A050
This 0.5m long female to female 25-Pin Micro-D Cable Assembly is constructed from 18/0.1 (26 AWG) copper wiring with PVC insulation and screening to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-6A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
