Converters
Change a form or value and shows or transforms it into a different scale or value.
-
product
Radiation Microdosimeters
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
product
Integrated Frequency to Voltage Converter
FV
The FV6 Frequency to Voltage Module provides a convenient method of converting up to six frequency signals to analog voltages that can be fed into common data acquisition equipment.
-
product
Electric Servo Motor Type Power Circulation Type Rotary Torquer Tester
Tests For Clutches Durability, Torque Converters, Transmissions, Differential Gears, CVJs, Etc. Can Be Performed At Low Cost By The Load Using The Power Circulation System.
-
product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
product
High Range Chemiluminescence NO/NO2/NOX Analyzer
Model T200H
Teledyne Advanced Pollution Instrumentation
The Model T200H combines the proven chemiluminescence principle with a number of innovative features to provide reliable and repeatable NO, NO2, and NOx measurements for extractive type CEM systems. A high-efficiency stainless steel thermal NO2 converter provides durable and consistent operation under the harshest conditions (other converter options also available).The T200H may be fitted with an optional, internal paramagnetic O2 sensor or an infrared absorption CO2 sensor, reducing integration and operating costs significantly.
-
product
USB Extenders / Repeaters / Hubs
CommFront has all the solutions that you need to make your data travel seamlessly without limits. We offer a range of rugged, industrial-grade USB extenders (repeaters) and hubs to meet your data communications' distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
product
Digital mammography system
AMULET
The new format FPD has a proprietary panel structure with a double layer of amorphous selenium that has high X-ray absorption properties, and was developed by combining Fujifilm''s "Device Development Technology" and "Vacuum Deposition Technology." The first layer efficiently converts X-rays into electrical signals, while the second layer employs the unique "Direct Optical Switching Technology," that captures higher resolution and lower noise image electrical signals rather than using electrical switches such as conventional TFTs. By achieving both "50µm fine pixel size (higher resolution) and low noise," the AMULET system can show microcalcifications and tumors in greater detail, both significant indicators for early diagnosis of breast cancer.
-
product
Trace Level Chemiluminescence NO-NOy Analyzer
Model T200U NOY
Teledyne Advanced Pollution Instrumentation
The Model T200U NOy analyzer has been developed and refined specifically to address the challenges of NOy monitoring as required, for example, in the US NCore network. It uses the proven chemiluminescence principle and is coupled with a remote NOy converter via umbilical to allow measurements with a lower detectable limit of 50 ppt.The Model T200U NOy analyzer combines a gold plated reaction cell with an enhanced performance pump, special low noise photomultiplier tube, and unique signal conditioning to provide exceptional sensitivity. In addition, a pre-reactor separates the NO-O3 reaction from background chemiluminescence to allow accurate auto-zero of the analyzer. The remote NOy converter is provided with a stainless steel, NEMA 4X (IP65) enclosure and custom sample umbilical to allow a mounting height of 10 meters. In addition, the converter features a unique purge circuit designed to remove residual calibration gas.
-
product
Analog Output Data Acquisition (DAQ) Products
Analog Output boards are useful when you need an output where the condition is not just an on or off state. Analog Output boards convert digital values generated by software into the analog voltage or current signals required for controlling frequency inverters, valves, sliders, brightness of lights, or things controlled by motors and other mechnical transducers.
-
product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
product
PWM to Voltage Output D/A Converters
Analog Devices’ pulse-width modulation (PWM) to voltage output D/A converters convert a PWM input to an accurate, stable, buffered voltage without the ripple, slow settling, and external passive components of discrete filter implementations. Our PWM D/A converters measure the period and pulse width of a PWM input signal and immediately update the D/A converter output with up to 12-bit accuracy and no software coding required. This family of D/A converters is available with 8-bit to 12-bit resolution, dual and quad channels, integrated references, and with high temperature operation. Applications include isolated motor control, automotive headlights or industrial lighting, and other applications that benefit from the simple control interface.
-
product
BNC (F) To Alligator Test Clips
3788
Minigrabber? test clip hooks attach to terminal sizes up to .060? diameter. Converts BNC (Male) cables to Minigrabber test clips for test versatility.
-
product
CompactPCI
CPCI-ADDA
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
product
96 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
The 96 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating and voltage handling up to 150Vdc. If you would like to develop your own cabling solutions, we offer mating connectors and connector hoods that allow you to create either your own cable based solutions, or a PCB header solution. Connector Blocks directly terminate the module connector and convert the connection to arrays of screw terminal blocks, or you can select to use a remote DIN rail mounted breakout to terminate the cables at the end of a cable assembly. You can also try our Cable Design Tool to graphically design a customized cable assembly.
-
product
SparkFun MicroMod Ethernet Function Board
W5500
Integrate your MicroMod project into an Ethernet network including Power-over-Ethernet with the SparkFun MicroMod Ethernet Function Board. This specialized Function Board uses the W5500 Ethernet control module from WIZnet and a DC/DC converter to configure a MicroMod assembly as a connected and powered device into an Ethernet network with a Power-over-Ethernet (PoE) system.
-
product
DCDC
QA Series
The QA series of cost sensitive single and dual output 5 watt DC/DC converters are specifically designed for critical applications requiring a compact, low profilecase.
-
product
Windows Managed Client/Server Software For BACnet Systems
CBQ
CBQ is implemented as a managed .NET 64 bit DLL. The DLL works with BACnet/IPv4 and BACnet/IPv6 over Ethernet, and you can even use MS/TP through USB or any standard serial COM port, with an external EIA-485 converter. Our famous MS/TP for Windows technology is unequalled and provides fast, reliable operation with direct connection to EIA-485 networks.
-
product
LAN⇔RS-422/RS-485 Conversion
SI-65
SI-65 is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
product
Low Noise Filter Adapter
PX0107A
The PX0107A converts Dsub25 outputs to five SMB outputs with the low noise filtering capability down to 25 μVrms (20 MHz). It supports the Keysight M9614/15A.
-
product
PCIe-7856, Kintex-7 160T FPGA, 1 MS/s, Multifunction Reconfigurable I/O Device
786455-01
PCIe, Kintex-7 160T FPGA, 1 MS/s, Multifunction Reconfigurable I/O Device - The PCIe‑7856 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7856 features a dedicated analog-to-digital converter per channel for independent timing and triggering. This device offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware.
-
product
Photometric Converter
C4000
The C4000 converter is a multi channel controller capable of operating all optek photometric sensors. The C4000 converter allows for easy programming and operation, and can supply up to four real time configurable 4-20 mA output values correlated to any units of measure. The C4000 offers configurable relay alarms, can record and download process data, and can operate up to four sensors simultaneously.
-
product
Fiber Transceiver Modules
Optical transceiver (transmitter and receiver) modules convert data signals to and from laser optic light and plug into routers, switches, and fiber host bus adapters (HBA). They provide the transmission of data between transceivers over fiber or optical cables.
-
product
Energy Metering ICs
Analog Devices’ ADE energy measurement ICs address the challenges of next-generation smart meter architectures and are ideal for measuring active energy (kWh), apparent energy (kVA), reactive energy (kVAR), rms, and power quality with the highest accuracy in single phase and polyphase revenue meters, industrial instruments, and energy monitoring applications. ADI’s ADE energy measurement ICs combine analog-to-digital converters with fixed-function digital signal processors to perform critical measurements, while providing unparalleled functionality and ease of use.
-
product
16-bit, 400KHz, 4 Isolated Analog Differential Inputs, Simultaneous Sampling
APCI-3003
With the new fast A/D converter board APCI-3003, the user can achieve high data transfer rates by a simultaneous conversion of 4 channels at once. The board has 4 differential input channels. Each channel has its own A/D converter. The transfer rate can be set in a flexible way from 100 kHz for each channel, when 16 channels are set, to 400 kHz for each channel, when 4 channels are set. All 4 channels are optically separated from each other up to 500 V.
-
-
product
HPx-346 Analogue to Network Radar Converter
The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.
-
product
Temperature and Humidity Regulator
H3331
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
product
Manage Power, Thermal & Control Planes In Real Time
Platform Manager 2 & L-ASC10
*Full fault coverage – monitor all rails and temperature nodes*Manage from 10 to 80 supplies using just the required number of L-ASC10 hardware management expanders*Minimize fault propagation by enabling individual hardware management sub-blocks (power, thermal & control path) to respond to faults in other blocks within nano-seconds*Save CPLD I/O pins by eliminating the need to monitor power-good signals of DC-DC converters*Reliable power & thermal fault detection in hardware, as opposed to software routines
-
product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
