Balancing
-
product
90deg Hybrid With Balanced Receiver
This page describes one of Optoplex's innovated products, a 90deg optical hybrid integrated with balanced photo-receivers, which can be used in optical sensing applications, particularly the coherent Doppler wind LIDAR (light detection and ranging). Coherent detection has been widely found in applications for RF and optical communications. In the past few years, coherent technology has been advanced dramatically in high-speed optical communications. With this advancement, key parts and components are commercially available and cost-effective for many applications beyond telecommunications, such as narrow linewidth lasers, optical hybrid, balanced photo-receivers, and DSP, etc.
-
product
Attenuators
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
product
RX Family Of 32-bit High Power Efficiency MCUs
The RX family consists of four product series: the flagship RX700 series, with the fastest performance and most advanced functions; the standard RX600 series; the RX200 series, which delivers an optimal balance of power efficiency and high performance; and the entry-level RX100 series, with extremely low power consumption. These four series encompass a range of products that provide seamless scalability from small-scale to large-scale applications.
-
product
40Gb/s Coherent Receiver
The integrated 40-Gb/s DP-QPSK receiver incorporates two 90° optical hybrids with four pairs of balanced photodetector (PD) and four linear TIAs into a single butterfly package. Unlike other technologies in which the polarization beam splitter (PBS) and/or the power splitter (BS) are not included, Optoplex’s receiver includes both of them with the optical hybrids, PDs and the TIAs to offer a fully integrated solution which will benefit users in terms of completely removing fiber routing and the skew management. The integrated receivers work at the symbol rate up to 12.8GBaud/s.
-
product
Automatic Engine Balancing Technology
AutoBalance™ System
Continuously adjusts fuel flow to each power cylinder to maintain balanced operationMinimize emissions and fuel consumption over a wide range of operating loadsReduce mechanical wear and maintenance costsReduce personnel costs and risk by eliminating manual engine balancingSupports engines with up to 20 power cylindersOn-Guard Diagnostic software for monitoring, analysis, reporting and trendingSupports automated air manifold pressure control for minimum emissions at varying loads
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S , Programmable Amplitude Balance
LS-16A-R1-24SLS
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Micro Analytical Balances
BM Series
Easy, fanless static elimination using a built-in ionizerBetter operability with a large weighing chamberInterlockable slide doors allowing efficient operation with both handsAutomatic calibration with an internal massClearly visible, white-backlit LCDBuilt-in temperature, humidity, and atmospheric pressure sensors
-
product
3U OpenVPX™ Intel® Xeon® SBC with One Smart Function Module Slot
68INT5
The 68INT5 is a 3U OpenVPX Intel® Xeon® Processor E-2276ME based embedded Single Board Computer with integrated output graphics/video & I/O expansion. Balancing high-performance with relatively low-power dissipation, the processor supports up to six processing cores operating at up to 2.8 GHz. One I/O expansion module slot is provided that can be fitted/configured with any one of the 70+ NAI smart I/O and communications function modules. Ideally suited for rugged Mil-Aero applications, the 68INT5 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Temperature Data Logger
DL001
Record temperature in a wide range of applications including HVAC testing and balancing, transportation, and energy management with the Model DL001 Temperature Data Logger. Temperature logger has an on-board thermistor and an external sensor channel for remote temperature measurements
-
product
Rotor Balancer
Static and Dynamic Balancing of Rotating MachinesBalanced rotors are essential for the smooth operation of rotating machinery. Unbalance will create high vibrations, reducing machine life and causing material defects. Our single and dual-plane balancing tool is a great tool to eliminate unbalance on-site reducing long down times.
-
product
Condition Monitoring
Falcon
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
product
Probing, Monitoring & Setting
Marposs offers solutions and equipment that make your machine tool an instrument of unprecedented precision, productivity and reliability. Touch probes and laser-based tool setters hold the cutting process accuracy in check. Our balancing actuators and many dedicated sensors guarantee that your machine tool's functional processes never deviate from their specified set points.
-
product
Balun
Balun is the component for converting balanced transmission line and unbalanced transmission line each other.Murata delivers high performance LTCC packaged product by multilayer ceramics integration technology.
-
product
ATX Motherboards
ADLINK's ATX motherboards provide optimal platforms for industrial automation, with one-piece PCBA design with no board-to-board connection significantly improving reliability and durability. The 305 x 244 mm profile is particularly suitable for space/cost sensitive applications where fewer than 7 slots are required. Rich features such as multiple PCIe/PCI/LAN/USB3.0 enable immediate multi-tasking deployment, balancing performance and expandability.
-
product
Bench Top Ionizers
Point-Of-Use Ionizer, Adjustable (30-100 PSI) Compressed Air IonizerNeutralize Electrostatic Attraction (ESA) to control contamination by dislodging dust and debris attracted by static electricity.Detachable 7'' long ESD Protective Flexible Hose with Thumb Button Designed to for a wide range of motion and simple operation.Adjustable Balance (20 Volts) with Less Than 1 Second Discharge Time At 6 InchMeets required limits ANSI/ESD S20.20 tested per ANSI/ESDSTM3.1 and ESD TR53
-
product
NanoVIP® TWO™
NANOVIP® TWO™ is a modern, powerful, portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (3 or 4 wires balanced) networks, low and medium voltage.
-
product
COM Express Module
CM22202
LinkedHope Intelligent Technologies Co.,Ltd.
CM22202 is a Type 6 COM Express® module developed by LinkedHope® based on China local x86 architecture ZX® KX-6000 series Processors. This module pinout is compliant with PICMG COM.0 R3.0 specification. CM22202 contains all kinds of high-speed interfaces such as SATA III, USB 3.0 and PCIe 3.0. CM22202 provides dual-channel SO-DIMM, supporting DDR4-2666 MHz memory and the capacity up to 32GB.CM22202 supports KX-6000 series 4 core processors which TDP from 25W to 55W. CM22202 provides high performance computing with balanced power consumption. CM22202 works well in a wide range temperature environment. It is ideal for the high-bandwidth and processing intensive requirements of industrial and edge computing applications.
-
product
- RS-485 DIN Rail Mounted Surge Suppressor
Model 8021NX
FEATURES: Fast Response; Automatic Recovery; Up To 20 MBPS Data Rate; DIN Rail Mounted; Triple Stage Protection; Two Wire. The Model 8021NX is a DIN Rail mounted surge suppressor for 2-wire RS-485 circuits used to protect factory data networks, or, any RS-485 network that wants to avail itself of the DIN Rail packaging concept. The Model 8021NX provides common-mode (line to ground) surge protection and differential mode (line to line) protection for balanced networks. All the inputs, outputs and ground connections are via screw terminals located on the top surface of the device.
-
product
Weighing Instruments
ZhangZhou Weihua Electronic co.,ltd
are devices to measure weight or calculate mass. Spring balances or spring scales measure force (weight) by balancing the weight due to gravity against the force on a spring, whereas a balance or pair of scales using a balance beam compares masses by balancing the weight due to the mass of an object against the weight of a known mass or masses. Either type can be calibrated to read in units of force (weight) such as newtons, or in units of mass such as kilograms, but the balance or pair of scales using a traditional balance beam to compare masses will read correctly for mass even if moved to a place with a different (non-zero) gravitational field strength (but would then not read correctly if calibrated in units of force), while the spring balance would read correctly in force in a different gravitational field strength (but would not read correctly if calibrated in units of mass).
-
product
Alnor Micromanometer
AXD620
The Alnor® Micromanometer AXD620 is a rugged, compact, comprehensive micromanometer that measures pressure. It can be used with pitot tubes to measure velocity and then calculate flow rates with user–input duct size and shape. Premium features make it ideal for HVAC, environmental safeguards, commissioning, process control and system balancing.
-
product
Check Current Before Working
Radio Ampstik® 2023
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
product
Vibration Test Chamber Elevator Mechanism System
Guangdong Test EQ Equipment co., Ltd.
- Structural Design: Monolithic construction with seamless TIG welding for durability and aesthetics. Lever-driven door lock mechanism.- Smart Control System: Features a Chinese/English-language color LCD touchscreen HMI + high-performance PLC, powered by TESTEQ's proprietary software for automated, intelligent, and user-friendly operation.- Energy Efficiency: Incorporates TESTEQ's patented "Static Balance" technology, reducing energy consumption by over 30% during low-temperature stabilization.- Vibration Integration: Elevator Mechanism: Wireless remote-controlled for alignment with horizontal/vertical vibration platforms.- Advanced Sealing: Custom flexible connectors ensure airtight integration between temperature/humidity chambers and vibration platforms.
-
product
Saluki LSG022 Analog Signal Generator (Modular)
Saluki LSG022 analog signal generator offers 100kHz to 22GHz frequency coverage with 10ms frequency switching speed. It can be used independently or combined with the chassis to form a test system.Saluki LSG series signal source is the cost-effective choice when you need to balance budget and performance. It provides the signals you will need for radar performance evaluation, high-performance receiver test and components parameter test etc..
-
product
M2T Transmitter
The M2T half-rack transmitter houses two stereo transmitters to provide two stereo audio channels, and for up to four mono audio channels in a single rack space. The audio inputs can be individually configured to be analog or Dante compatible. The analog input connectors are full-size XLR/TRS combo types for balanced line-level analog signals while the input preamp circuits use a special balanced amplifier with very high common mode rejection to minimize hum and noise. A Dante™ Ultimo™ interface via dual RJ45 connectors accepts Dante networked audio inputs and can daisy chain the digital stream to additional units via CAT6 cables. An additional RJ45 jack provides an Ethernet connection for programming and control via Wireless Designer™ software and a USB jack on the front panel allows for firmware updates. The transmitter features a full color, backlit LCD for high visibility in any environment, while the chassis is all-metal and can be racked singly or in pairs using included rack mount hardware.
-
product
4K Autofocus MIPI NVIDIA® Jetson TX2 Camera Board
E-CAM132_TX2
e-CAM132_TX2 - 13MP Autofocus Jetson TX2 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® and an integrated high-performance image signal processor (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control). e-CAM132_TX2 is a two board solution consists of a base board and a 13MP autofocus camera board. This camera board is connected to the base board using 30 cm micro-coaxial cable.
-
product
Power Supplies
V-600
The V-600 is feature a 140mm ultra silent cooling fan and single PCI-E connector to power your high-end graphics card and keep your system cooler. The triple rail 12V outputs design allow for optimum load balancing in better performance and stability.
-
product
Ballast Water Monitoring Systems
Ballast water is essential for safe and efficient shipping operations and stabilizing steel-hulled vessels at sea. It provides a variety of critical functions, such as maintaining balance, stability, and structural integrity on non-cargo voyages or when cargo is unloaded. Ballast water is also used to compensate for fuel and water consumption during at-sea operations.
-
product
DC Bias Current Power Supply
TH1775
Shenzhen Chuangxin Instruments Co., Ltd.
TH1775 is a DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. High frequency LCR meter could be used, when the frequency response range is wide enough. MPU controlled auto current balance technology is adopted to realize AC+DC current overlap and constant current output from 0 to ±20A. Two TH1775 can be paralleled to supply a maximum current up to 40A.TH1775 permits high frequency measurement up to 1 MHz and can be directly controlled by TH2816A, TH2817A, TH2818 and TH2819. TH1773/TH1775 with its low additional error, wide frequency response range and sweep output function is widely used in DC biased inductance measurement. TH1775 also provides a perfect solution for magnetic material analysis.
-
