Distribution
transmission's network array.
-
product
Gas & Flame Detection System
Syntel
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
product
8-Channel VME Delay Generator for Facility Timing Systems
V880
The V880 is a VME-based system timing module, used to distribute picosecond-precision timing pulses across physically distributed facilities. The V880 receives a 155.52 MHz (OC3 rate) fiberoptic master timing signal and outputs eight local triggers.
-
product
Frequency & Pulse Distribution
Timetech frequency distribution amplifiers and pulse distribution units.
-
product
Fluid Distribution Panels
PAO-DII
As a further convenience, we offer our PAO-DII Fluid Distribution Panels to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger second generation PAO-II Chiller. You can also use PAO-DII Fluid Distribution panels with any other source of temperature controlled fluid including a Bemco PCL-III Portable Chiller. These systems are individually assembled to match the product being tested.
-
product
Ethernet-based Distributed Systems
DMC-3425
The DMC-3425 is the first product in Galil's new E-Series line designed specifically for Ethernet-based distributed systems. The DMC-3425 provides a highly versatile and powerful form of distributed control where multiple DMC-3425 controllers are linked together. When linked, one DMC-3425 is designated as the master over the other DMC-3425 controllers in the distributed system.
-
product
Fast Response Gas Detector
Leaksurveyor
Teledyne Gas & Flame Detection
The GMI Leaksurveyor combines quality, ruggedness and advanced Technology in a user friendly, portable gas detector. The integral fast response and high sensitivity semiconductor sensor enables leakage surveys to be performed and distribution leaks to be quickly found.
-
product
GONIOPHOTOMETRY
Goniophotometers are required to measure angular resolved distributions of photometric or colorimetric quantities, either by rotating the lighting device under test or by moving the sensor around the device. Depending on the application, different geometries are used to obtain distributions in the appropriate CIE coordinate system.
-
product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
-
product
Spectroradiometer
Designed to have a capability of producing any visible spectral distribution, mimicking various light sources in the visible region by feedback control of the radiant power emitted by individual LEDs. This LED test system will be used as a transfer standard for photometric, colorimetric and radiometric applications.
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52641
Ideal radar and software radio interface solutionOne-channel mode with 3.6 GHz, 12-bit A/DTwo-channel mode with 1.8 GHz, 12-bit A/Ds2 GB of DDR3 SDRAMProgrammable one- or two- channel DDC (Digital Downconverter)PCI Express (Gen. 1 & 2) interface x8 wideSync bus for multimodule synchronizationOptional LVDS connections to the Virtex-6 FPGA for custom I/O3U VPX form factor provides a compact, rugged platformCompatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions availableSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
6U OpenVPX 6 Slot Profile BKP6-DIS06-11.2.10-3
1OVX606BX6-1X01R
6U OpenVPX backplane features 6 slots, a distributed mesh data plane topology with a data rate of up to 6.25 Gbaud per channel and a switched control plane topology.
-
product
Near Field Moving Detector Goniophotometer
LSG-1900B
LSG-1900B Goniophotometer is near field Type C automatic goniophotometric instrument for luminous intensity distribution measurement. The LSG-1900B uses a constant temperature detector. It is for industrial laboratory photometric data measurements of small luminaires, such as down light, bulb light, etc.
-
product
Video Signal Distributor
MSDD-02D
MSDD-02D distribute the Analog Signal through the two (2) output without any diminution & distortion. The DDC line is designed with consisted of the two (2) channels in order to make the EDID data set up with the two (2) displays monitors at the one (1) same time. With two (2) generation by adapt as individually using the quick speed IC for exact output at the video data respectively, there is no signal deviation between input & output signal.
-
product
Aerospace Onboard Software Modules
ADS2 for Aerospace
Your product description goes here. The Aerospace Onboard System Development Process is guided by SAE ARP4754A. It consists of multiple levels of specification, design, validation and verification and is distributed between OEM and multiple suppliers of systems, subsystems and components.Due to the complexity of the development process, a consistent platform supporting model based validation, virtual and physical integration as well as requirement based verification at each level is of great importance for the industry.
-
product
Distributed Simulation & Test Environment
Modular hardware and software architecture with multipurpose modules and components in a common and reconfigurable simulation and test environment easily adaptable to meet project‐ and customer‐specific requirements.
-
product
Automated Stand for Magnetic Luminescent Control of Railway Wheels
The amount of information processed and time constraints required the creation of a multi-level distributed image processing system based on National Instruments Compact Vision System controllers, industrial computers and workstations. During the control process, the wheel is watered with a magnetic-luminescent emulsion, magnetized and exposed to ultraviolet radiation. As a result, the emulsion deposited on the defects glows in the visible range (yellow-green light). Eleven FireWire (IEEE 1394) color cameras with a resolution of 1280 x 1024 are used to scan the wheel surface. In one iteration, they completely cover a 20-degree sector of the wheel.
-
product
Plunger Tester
PL2003
Designed and manufactured in accordance with ASTM F414, DOT571.109, F870 & JIS D4230 standards. New generation of PL-2000X series Plunger Testers, equipped with servo-hydraulic system to control the testing speed, are available fpr customers to select the suitable model. Test functions including Radial elasticity test, Tread footprints test, Tire dimension test, Bead unseating test, Lateral elasticity test and Pressure distribution analysi for Footprints.
-
product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
NTP Time Servers
The Masterclock NTP100 family of NTP time servers provide accurate timing to networks and conform to NTPv2 (RFC 1119), NTPv3 (RFC 1306) and NTPv4 (RFC 5905). Each NTP100 device can operate on a local area network (LAN) or act as an enterprise-wide source for legally-traceable time and date distribution, depending upon your network configuration requirements. Masterclock NTP time servers are compatible with IPv4/IPv6 networks and offer AES256 SSH encryption, as well as MD5 authentication, for secure communications.
-
product
Heavy Copper PCB
Your product descrVictory is a professional Advanced Circuit Manufacturer, We provide 3OZ ~ 6OZ Heavy Copper PCB.Heavy Copper PCB are generally used for high power distribution, heat dissipation, planar transformers, and power convertors. We can make up to 6oz Heavy Copper PCB.iption goes here.Monthy Capability: 3500 Sq M/MonthLayer: 4 LayersMaterial: FR4 TG170Dimension: 350.56mm*580mmFinished board thickness: 2.3mmOuter layer Finished copper thickness: 6ozInner layer base copper thickness: 6ozMin Trace Width/Space: 14milMin hole size: 0.2mmMin hole wall copper: ≥25UMSoldermask Color: Gloss BlackSilkscreen Color: WhiteSurface finishing: HALApplication field: Communication Field
-
product
Color Matching Booth
GSM Round Cutter is used to test material grams per square meter. It would cut sample to 100cm2 cutter, depth max 5mm. Normally, GSM cutter is suitable to cut textile fabric, leather, paper and etc. It has four double-sided blades, and the blade is evenly distributed in four equal parts. The blade can be replaced. GSM Testing is essential for some tests like Matindale abraison test meet standard ISO20344.
-
product
8-Channel 200 MHz, 16-bit A/D with Virtex-6 FPGA - 6U VPX
Model 58660
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Eight 200 MHz 16-bit A/Ds- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Value Power in ABS Plastic Housing (12) 5-15R 1U/0U V/H
EPS-1215-HVP
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Circuit Breakers
Our broad portfolio of Hydraulic-Magnetic Circuit Breakers, Switches, GFCI/ELCI Modules, and Modular Distribution products, deliver consistent quality with a wide range of features, tailored solutions to meet your application.
-
product
Encoder
SFT3228S
Hangzhou Softel Optic Co., Ltd.
3228S Multi-Channel encoder is a professional HD/SD audio & video encoding device. It has 8/16/24 HDMI inputs for option. Every 8 HDMI ports share one encoder module with each module supporting 1MPTS and 8SPTS output. Its high integration and cost effective design makes the device widely used in varieties of digital distribution systems such as cable TV.
-
product
Uniformity Calibration Standards
Integrating sphere light sources with halogen lamps or LEDs for generating luminous fields with uniform luminance distribution. Traceable calibrations of luminance or spectral radiance in the wavelength range from 250 nm to 2500 nm.
-
product
Emergency Power Supply Units (EPSU) (14) 5-20R 1U/0U V/H
EPS-1420-HV
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
product
Advanced 8-Axis Servo & Stepper Motion Controller with Modular Design
PCI-8158
The PCI-8158 delivers high-frequency pulse rates of up to 6.55 MHz and features hardware-controlled emergency input stop, software security protection to avoid plagiarism, card index switch, and linear/circular run at the same time for that exceed the industry"s cost over performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and steppers, the PCI-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for various linear-wise and circular-wise trajectories, the PCI-8158 delivers the smoothest motion control for a wide-range of manufacturing applications. Besides, PCI-8158 design is modularized. ADLINK provides extension board for distributed I/O control, high-speed triggering and ECAM control.
-
product
1-Ch 3.6 GHz or 2-Ch 1.8 GHz 12-bit A/D with DDC, Kintex UltraScale - 3U VPX
Model 52841
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 5 GB of DDR4 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
Up-Converter for Radio Amateurs
. Internal filters provide high spurious rejection and image rejection. Due to low phase noise and high frequency stability of the local oscillator at 3000 MHz, the up converter is suitable for analog and digital communication systems.Typical applications are Multichannel Multipoint Distribution Systems (MMDS) using QPSK modulation and DVB?T or DVB?S systems. The output power of 20 mW can be increased to several watts by the use of an additional power amplifier.
