Product

ABex Terminal Module for JTAG Technologies JT 37x7 BSCAN Cards

ABex TM-JT37x7

-

Konrad Technologies GmbH

ABex TM-JT37x7 - Konrad Technologies GmbH

The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.

Product

AC & DC Aging Test Equipment for Arrester Valve Plate

-

Shanghai Guantu Technology Co., Ltd.

Shanghai Guantu Technology Co., Ltd.

The arrester is usually connected between the live wire and the ground, and is connected in parallel with the protected equipment. When the overvoltage value reaches the specified operating voltage, the arrester will act immediately, flow the charge, limit the overvoltage amplitude, and protect the insulation of the equipment; when the voltage value is normal, the arrester will quickly return to its original state to ensure the normal power supply of the system.

Product

Voltage Testers

-

Morris Products Inc.

Morris Products Inc.

Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece

Product

Elongation Tester

SC-5

-

Shanghai Dean Electrical Co., Ltd

SC-5 - Shanghai Dean Electrical Co., Ltd

Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.3-2008Used to test elongation (ductility) of copper wires covered with φ0.100-3.0 mmenamel, silk or other insulation materials and other metal wires with tensile strength ≤2000N;Application of SCM control allows for fast operation and strong anti-interference capacity;Preset elongation of samples with two-digit toggle switch and, when the preset value is reached during test, motor and counter would automatically stop action and display results;The instrument is capable of measuring elongation while also the tensile force and holding the maximum tensile force value during stretching;Clamps are designed according to characteristics of various wires to prevent samples from breaking at clamp jaws, easy to load samples and, after samples are compressed, enamel can be automatically broken;While sample is broken, movable clamp would automatically stop moving, with error between displayed and actual elongation value less than 1%;

Product

Glow Wire Tester

-

Shanghai Dean Electrical Co., Ltd

Shanghai Dean Electrical Co., Ltd

Glow wire tester would stipulate material (Ni80 / Cr20) and the shape of the heating wire (4 mm Φ nichrome wire) in large current heated to test temperature (550 ℃ ~ 960 ℃, after 1 mi to specified pressure (0.95 + / - 0.1 N) vertical burning hot try 30 s, inspect goods and bedding content whether light-off or the burning time to determine the fire risk of electrical and electronic equipment finished product;Determination of ignitability, ignitability temperature (GWIT), ignitability and ignitability index (GWFI) of solid insulation materials and other solid combustible materials is also applicable to the industries of insulation materials, engineering plastics or other solid combustible materials.

Product

High Temperature Furnace COD Gages (1200 C or 1600 C)

Model 3548COD

-

Jinan Testing Equipment IE Corporation

Model 3548COD - Jinan Testing Equipment IE Corporation

These COD gages mount on a water-cooled bracket, which is mounted on the furnace side cut-out or with optional load frame support brackets. The standard temperature version (to 1200℃) is supplied with high purity alumina rods. The high temperature option is furnished with alpha grade silicon carbide rods. Rods are made to order to the length required for your furnace. Mounting brackets may be integrated with the furnace cut-out. Epsilon can also provide optional load frame mounting brackets to fit your test frame. Contact edges on the test sample should be somewhat rounded (not sharp knife edges) for best performance with this model. The Model 3548COD extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.

Product

High Resolution Inline AXI Platform

AXI XS Series

-

Nordson Corporation

AXI XS Series - Nordson Corporation

The XS-platform series is a small-footprint high-resolution automated X-ray inspection system concept designed for sophisticated high-speed inspection of semiconductor samples, wire bonds and PCB-assembly boards for single/multipanels or samples in trays. The inspectable applications range from component level inspection to mid-sized SMT boards.

Product

QTI Sensor

555-27401

-

Parallax Inc.

555-27401 - Parallax Inc.

The QTI Sensor is a close-proximity infrared emitter/receiver that is able to differentiate between a dark surface) with low IR reflectivity) and a light surface (with high IR reflectivity). These little sensors can be very handy for line following, maze navigation, or sensing the outer rim of a SumoBot ring. Wiring options allow it to be used digitally for fast black/white line following, or as an analog sensor to detect different shades of gray. A daylight filter is built into the sensor.

Product

HDMI Cable Tester

MT-7062

-

Prokit's Industries Co., Ltd.

MT-7062 - Prokit's Industries Co., Ltd.

Test all HDMI cables with Type A to A, A to C and C to C connectorsDesign with loopback function allows test HDMI type A to A, A to C on main unit.Automatically fast & slow scan for testing all conductors status in a cable, Manual test for step by step detecting individual conductors for intermittent faults.Automatically detect wiring on HDMI type A or type C condition in straight, short, open, crossover in all RGB conductors.Quickly troubleshoot and verify HDTV installation and DIY termination in the field.

Product

Clamp Multimeters

-

Gardner Bender

Gardner Bender

Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.

Product

Wire Damaged Tester

WDT-1

-

Lisun Electronics Inc.

WDT-1 - Lisun Electronics Inc.

This equipment is designed and manufactured according to corresponding regulation in standard IEC884-1, GB299.1-96, GB16915.1-97 and other electronic accessories relevant standard. Mainly used to test damage degree of fixed connection components lead wire of with thread clamping type and no screw terminals, so as to inspect whether it can withstand mechanical stress during normal use.Specification: • Power supply: AC220V 50Hz • Test rate: 10±2r/min (GB16915.1-97: 12 ±1r/min) • Rotating radius: 100mm • Test distance: 250~500mm adjustable • Test numbers (Number of rotating): 0~999999 any set • Mass: 0.3KG, 0.4KG, 0.7KG, 0.9KG, 1.4KG, and 2.0KG (GB16915.1-97: 30N, 40N, 50N, 60N each of 2 pcs) • Stations: 2 • Dimension: 1200×1400×400 (mm) • Remarks: The mass and rotating radius can be optional as per customer requirements.

Product

Position Sensors & Encoders

-

Sensata Technologies

Sensata Technologies

Sensata's position line from Kavlico, BEI Sensors and Newall, make up our highly-engineered devices that span the entire range of position sensors, linear and rotary encoders, potentiometers, draw wires and inclinometers. They’re designed to deliver:

Product

Static & Lighting Chokes

-

LBA Group, Inc

LBA Group, Inc

Lighting chokes are used to pass tower lighting voltages across the base insulator of a series-fed tower without appreciably altering the tower impedance. LBA TC-300 general purpose tower lighting chokes are provided for three wire 110/220 VAC circuits. Maximum current is 25 amps. These chokes are rated for peak base voltages to 10,000 volts, and present a typical reactance of +j5000 ohms at 530 kHz. Bypass capacitors are provided on each winding.

Product

WireScan

LPA56B Series

-

OES Technologies

LPA56B Series - OES Technologies

Strip and Seal Inspection100% in-process inspection and traceabilityFor Integration on Automatic Wire Processing Machines

Product

DC Resistance Tester

DCSS502BC

-

Sanshine Electronis Co., Ltd.

DCSS502BC - Sanshine Electronis Co., Ltd.

Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.

Product

Battery Discharger & Capacity Tester

IDCE-CT

-

Fuzhou Fuguang Electronics Co., Ltd.

IDCE-CT - Fuzhou Fuguang Electronics Co., Ltd.

Each wireless module can monitor 4 batteries simultaneously comparing with the traditional method that each module only canmonitor 1 battery, the new wiring operation become easier because the quantity of new modules needed is only a quarter of old-fashioned modules.

Product

Wireless Connectivity 4 in 1 Digital Multi Detector with moisture measurement

MS-W68(11B)

-

MEET International Ltd.

MS-W68(11B) - MEET International Ltd.

External wireless connectivity 4 in 1 Digital Multi Detector can detect live wires and metal pipe / conduit in walls and wooden stud in drywalls, with audible and numerical display on LCD.

Product

Network Toner & Probe Kit

MT-7028

-

Prokit's Industries Co., Ltd.

MT-7028 - Prokit's Industries Co., Ltd.

The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.

Product

Weather Resistant Surge Protector for RS485 Control & 12VDC Power Lines

SP-RS485-12V-O

-

Network Technologies Inc

SP-RS485-12V-O - Network Technologies Inc

Ideal for applications such as video surveillance cameras and access control. Protects sensors running on 22 AWG 2-wire sensor cables or 12VDC power lines against the effects of electrostatic discharge, faulty wiring and lightning. RS485 protection: Stage 1 clamping voltage: ±90V; Stage 2 resistance: 3.3 Ohms; Stage 3 clamping voltage: ±7.5V. 12VDC power lines protection: Stage 1 clamping voltage: ±90V; Stage 2 current rating: 3A; Stage 3: 12V TVS (transient voltage suppression) diode. Screw terminal pairs for RS485 and 12VDC power lines protection. Will also protect two single ended data, analog or control lines. Impact and weather resistant enclosure with locking hinged cover.