Product

Embedded Vision And Processing FPGA

CrossLink-NX

-

Lattice Semiconductor

CrossLink-NX - Lattice Semiconductor

*Instant-on configuration – IO configures in 3 ms, and device as fast as 8 ms*Two hardened 4-lane MIPI D-PHY transceivers at 10 Gbps per PHY / 2.5 Gbps per lane*Up to 37 programmable source synchronous I/O pairs for camera and display interfacing

Product

8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - 6U VPX

Model 57131

-

Mercury

Model 57131 - Mercury

- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports one Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available

Product

Goniophotometer

GMS2000

-

OptCom Company, Ltd

GMS2000 - OptCom Company, Ltd

In this goniophotometer, the tested luminaire rotates in the prescribed burning position and around the vertical axle and a reflecting mirror rotates around the horizontal axle, meanwhile, a synchronous axle will rotate toward the opposite direction synchronously. The combined motion of the luminaire and mirror permit luminous measurement at the direction of any horizontal or vertical angle without tilting the luminaire, therefore, the luminous intensity will be not variation. The photometer head located at a fixed position of the limiting photomet- ric distance in front of the reflecting mirror to gather the light in each direction.

Product

PCI Bit Synchronizer

LS-40-P

-

Lumistar Inc.

LS-40-P - Lumistar Inc.

The Lumistar LS-40-P PCI Bit Synchronizer provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a consistent product with high reliability and long-term stability. The LS-40-P PCI Bit Synchronizer consists of the LS-40-DB Bit Synchronizer Daughterboard shown below mounted on a PCI carrier board.

Product

Hyperspectral Cameras With USB3 Vision

XiSpec

-

XIMEA GmbH

XiSpec - XIMEA GmbH

*Smallest Hyperspectral camera - Compact, lightweight with only 26.4 x 26.4 x 31 mm, 32 grams (1)*Cost efficient - Excellent value and price through utilizing new imec hyperspectral imaging technology*Cool economy - Low power consumption with 1.6 Watt, minimal heat dissipation, ideal for UAV / UAS*All-around support - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM*Powerful potential - Highest spatial and spectral resolution, possible with 5Gb/s interface*Optimized - 2048 parallel, "on-chip" integrated spectroscopes with 100 points of spectral resolution each*AIA standard - USB3 Vision standard compliant*Industry standard interface - Compatible with USB 3.0 SuperSpeed specification*Fastest Hyperspectral camera - High speed, high frame rate: based on 170 fps at 2.2 Mpix resolution*Connectivity and Synchronization - Programmable optoisolated input and output, 3 status LEDs*Easy deployment - Range of accessories and wide hardware and software integration*Highly Customizable - Variety of sensor options, which can be further adjusted to match requirements*Interoperability increase - Continuous embrace of new software and hardware partners

Product

4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - XMC

Model 71761

-

Mercury

Model 71761 - Mercury

- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe

Product

Logic Analyzer

LAP-16064U

-

Zeroplus Technology Corperation

LAP-16064U - Zeroplus Technology Corperation

Sample rate (Internal clock): 100MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.

Product

AWD Dynamometers

MD-AWD-500-AC/EC-100/250

-

Mustang Dynamometer

MD-AWD-500-AC/EC-100/250 - Mustang Dynamometer

The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.

Product

8-Channel 250 MHz A/D with DDC, Kintex UltraScale FPGA - PCIe

Model 78131

-

Mercury

Model 78131 - Mercury

- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized versions available

Product

8-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - 3U VPX

Model 52132

-

Mercury

Model 52132 - Mercury

- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Ideal radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Eight 250 MHz 16-bit A/Ds- Eight wideband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2, &3) interface up to x4- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available

Product

L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX

Model 57791

-

Mercury

Model 57791 - Mercury

- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe

Product

Wave Buoy

MOTUS

-

Aanderaa Data Instruments AS

MOTUS - Aanderaa Data Instruments AS

The MOTUS (movement in Latin) Wave Buoy is a perfect solution for collecting environmental data in coastal areas.Collect reliable environmental data with MOTUS Wave Data Buoy.The MOTUS (movement in Latin) Buoy is a perfect solution for collecting environmental data in coastal areas for all-year deployments. The platform used for collecting data is a robust buoy which has proven to be an excellent platform for providing high accuracy and reliable meteorological and oceanographic data. The wave buoy can effectively combine various Hydrological and Meteorological parameters. Basic parameters such as wind, waves, and currents can easily be expanded to include sensor packages with different water quality sensors. Data is controlled and synchronized by the data management systems that Xylem Analytics offers, which also controls and powers real-time communication. This provides a low-power efficient system offering long-term deployment capabilities.The MOTUS Wave Buoys combine our ultra-low power and field-proven solutions from developing oceanographic and water quality sensors. We have 60 years of experience operating in the industry, providing you with an optimal platform based on the buoy, a rugged, lightweight polyethylene buoy deployed in more than 40 countries all over the world. By selecting Xylem as your partner in your projects, you are on track for the lowest overall cost of ownership and a versatile platform that can be tailored to your needs. The MOTUS Buoy is developed for both scientific and commercial use.

Product

Advanced PC/104 Timing Board

PC104-Plus SyncClock32

-

Brandywine Communications

PC104-Plus SyncClock32 - Brandywine Communications

The PC/104Plus SG from Brandywine Communications provides precision time with zero latency to the host computer over the PCI bus. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or HaveQuick.

Product

Airborne Receivers & Bit Synchronizers

-

Lumistar Inc.

Lumistar Inc.

The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.