DAQ Systems
Sense, log and store information.
-
Product
PXIe System Sync Module, 2 Port
M9032A
System Sync Module
The M9032A has a Soft Front Panel (SFP) that provides a graphical user interface to the system sync module. It allows the user to set up the most commonly used functionalities of the module. The SFP also gives you the ability to check the module's connection status, configure the reference clock and IO settings, and perform firmware udpates.
-
Product
Configurable Functional Test System
ATS-5000
Test System
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
Product
Dual Sensor Enhanced Vision Systems
EVS
System
Enhance your safety and situational awareness while flying with Max-Viz dual sensor enhanced vision systems (EVS) from Astronics. These multi-spectral imagers include a long wave infrared sensor, a visible light + near infrared sensor, and patented blending and dynamic range management image processing to enable pilots to see clearly during day and night.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Electronics Testing Solutions
Test System
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
Product
Mezzanine System
5181
System
ECM P/N 5181 uses TI TLV320AIC23 high resolution audio codecs to provide two channels of Audio input and two channels of Audio output. Each input channel consists of two inputs a left and a right, and each output channel consists of two outputs left and right. The outputs are muteable.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Automated Test Systems
Test System
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Bloomy Simulation Reference System
System
The Bloomy Simulation Reference System provides a hardware in-the-loop (HIL) test environment for dynamic, closed-loop testing of many aerospace and transportation control systems. The reference system integrates the computing, I/O, and software components needed for standalone use or to form the basis of a more complex test system.
-
Product
Mezzanine System
5235
System
The 5235 ECM provides 16 bits of simple digital I/O. The digital I/O is connected directly to the digital I/O on the carrier card. Inputs are clamped to about 3V by FET buffer ICs, and are 5V tolerant.
-
Product
Electrification Testing Solutions
Test System
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
In-Circuit Test System
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
VLSI Test Systems
Test System
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
Development System
PCIe490
System
The PCIe490 Expansion Chassis enables users to scale application workstations with up to eight additional PCIe boards per chassis and up to 63 total slots with chassis daisy chaining. It was designed to accommodate the Abaco Systems PC820 and PC821 with Xilinx Ultrascale technology and multiple FMC+ interfaces.
-
Product
Mezzanine System
5158
System
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
Product
NI LabVIEW Base Development System for Windows
System
NLabVIEW is system engineering software designed for applications that require test, measurement, and control with rapid access to hardware and data insights. The LabVIEW Base Development System is recommended to integrate NI hardware and third-party devices together to build automated desktop measurement applications with an intuitive graphical programming syntax.For applications that require advanced inline analysis or PID control, consider LabVIEW Full Development System.
-
Product
Flying Prober Test System
QTOUCH1404C
Test System
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
Product
CATR Benchtop Antenna Test System
ATS800B
Test System
Very compact far-field over-the-air (OTA) test system based on compact antenna test range (CATR) technologyUnrivaled quiet zone size within 0.8 m2 footprintState-of-the-art reflector ensuring a high quiet zone accuracyUnique benchtop CATR system supporting over 50 GHzIndirect far-field method (approved by 3GPP for 5G OTA testing)
-
Product
VLSI Test System
3380P
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (512 I/O pins to test 512 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
System Integration
System
G Systems develops fully integrated systems and we know that both software and hardware are equally important to system design. Our focus on code quality and optimization ensures customers receive efficient and maintainable code. We specialize in LabVIEW development and all of our LabVIEW developers are certified developers or architects. We’re also highly skilled in mechanical and electrical hardware design and builds on a wide variety of data acquisition, signal conditioning, RF, and distributed communication platforms.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
2-Module ICT System, I317x Series 6
E9902G
In-Circuit Test System
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
DAQ Devices
-
LabJack makes USB/Ethernet based measurement and automation devices which provide analog inputs/outputs, digital inputs/outputs, and more.We provide a robust and highly supported interface between computers and the physical world.
-
Product
Multi-Function DAQ
-
Full spectrum of DAQ cards provides analog input and output, digital input and output, and counter/timer circuitry.
-
Product
DAQ Cards
-
DAQ cards are high-speed yet cost-saving products, including PCI DAQ and PCIe DAQ that feature multifunction I/O selections such as analog I/O.
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
Modular Breakout System 3-Pin & 20-Pin Plugin Module
95-199-004
Modular Breakout System
The 95-199-004 Plugin Breakout Module is designed to be fitted to a PXI 40-199 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Battery Management Systems Testing
System
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
