-
Product
PIN Diodes
-
PIN photodiodes convert light to current – without a bias voltage having to be applied. Silicon is commonly used as an inexpensive detector material in the Vis range. For higher demands, InGaAs is used; it covers the widest spectral range from the Vis to the NIR. We offer silicon carbide as a “solar-blind” detector specifically for the UV range.
-
Product
34 Pin IDC Connector Accessories
-
Ideal for user created termination schemes where the termination is to be remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearance for the voltage that the application requires.
-
-
Product
SP4T RF Pin Diode Switches To 16 GHz
-
The 4-way series of absorptive and reflective switches operate from 100 MHz to 16 GHz. They are rated at 200 mW maximum input power and have a switching time of 100 ns. SP4T switches that operate up to 8 GHz have a maximum VSWR of 1.6:1 and minimum isolation of 60 dB. All absorptive and reflective switches manufactured by Pulsar Microwave require both positive and negative 5-volt supplies. Additionally, the TTL control logic operates from 0 to +5 VDC. Voltage connection is made with feed thru terminals. Ground connection is made through the chassis and turret terminals.
-
Product
Additional Products: 15 Pin D-Type Connectors
-
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
200 Pin D Cables - 200 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m HV, Exit Away From Pin 1
40-970-050-1m-FF-HV
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML DSub
540111030503
-
Cable Assembly, Receiver, 72", TriPaddle, 50 Pin FML DSub.
-
Product
Alignment Pin Replacement Kit, G2/G6/G10, Receiver
310118000
-
This kit contains parts/ tools needed to replace missing or damaged alignment/ dowel pins on the G2, G6, or G10 receiver: 2 alignment/ dowel pins Loctite primer Loctite adhesive Dimension blockInstructions for replacement can be found in G2/G6/G10 user manual.
-
Product
100 Pin Micro-D Cable, Male To Male, 0.5m 2-56 UNC Screwlocks, Metal Shell
A100SMR-100SMR-9B050
-
This 0.5m long male to male 100-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28 AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Screwlocks are provided to secure the connectors to their associated products. This cable assembly is suitable for use with Pickering BRIC modules that use the 100-pin Micro-D connector.
-
Product
Additional Products: 160 Pin DIN 41612 Connector Blocks
-
The connector blocks below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 160 Pin Male LFH
540262010140
-
Cable Assembly, Receiver, QuadraPaddle, 20", 160 Pin Male LFH
-
Product
100 Pin 1.27mm Pitch Micro-D Connectors for Pickering
-
The connectors below are suitable to use with Pickering cards and modules that utilize a 100-pin Micro-D connector.
-
Product
8 Pin Power D-Type Female Connector, 40A, Without Backshell
92-960-008-F
-
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Male, 1m, Exit Away From Pin 1
40-970-050-1m-MM
-
The 50-Pin Cable Assembly is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
DL-ISO 2500 Vpp Square Pin Tip
DL-ISO-2500V-TIP
-
- Ideal for GaN and SiC devices- Highest system accuracy- Fastest rise time- High CMRR - 160 dB
-
Product
96 Pin 1.27mm Pitch Micro-D Connector & Cable Accessories
-
The 96 Pin 1.27mm Pitch Micro-D Connector is used on high-density PXI modules that require 1A current rating andvoltage handling up to 150Vdc.
-
Product
Cable Assembly, 50-Pin D-Type, Female To Unterminated With Ferrules, 1m HV, Exit Away From Pin 1
40-972-050-1m-FU-HV
-
50-Pin Female to Unterminated D-Type Cable Assembly, High Voltage, With Ferrules, 1m Long, 45º Cable Exit Away From Pin 1.
-
Product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 48", 780009-02
VFL159124-048
-
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 48" length.
-
Product
25 Pin D-Type Connector Blocks For Pickering Products
-
The connector blocks below are suitable to use with Pickering cards and modules that utilize a 25-pin D-type connector.
-
Product
PIN Diodes
-
The SemiGen SGP7000 series of PIN Diodes are processed with a high-resistivity epi that have intrinsic layers that range in thickness from 4 micron to 200 micron depending on performance specifications. These devices are typically manufactured with either a robust thermal-oxide passivation or ceramic glass for durable high-power applications. These diodes are made with a grown junction P++ layer that yields abrupt junction structures that provide low punch through voltages and minimize autodoping. They are available as chips or in your choice of packages.
-
Product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 60", 780009-02
VFL159124-060
-
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 60" length.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m, Exit Towards Pin 1
A050DF5-050DF5-0A100
-
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 68-pin micro-D connector.
-
Product
Additional Products: 15 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB
540285010203
-
Cable Assembly, Receiver, 36", Tripaddle, 96 Pin 2X InfiniBand SMB.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH w/ M3 Jackscrews
540105010105
-
Cable Assembly, Receiver, TriPaddle, 20", 200 Pin Male LFH w/ M3 Jackscrews.
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 68 Pin VHDCI Plug
510109473
-
PCB adapter from a 192 position QuadraPaddle receiver module to one 68 pin VHDCI plug
-
Product
Pin Insertion Tool For Scorpion Connectors With Crimp Pins
C020AFR-2CP-2A-I
-
Extractor tool for crimp pins fitted into a Scorpion connector housing.
