Resistive Load Banks
Check power source's ability to deliver a given current and voltage at unity power factors.
See Also: Load Banks, AC Load Banks, DC Load Banks, Inductive Load Banks, Reactive Load Banks
-
Product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
Receiver Module
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
ITO Sheet Resistance Standards (ITOSRS)
-
Indium Tin Oxide Sheet Resistance Standards (ITOSRS) from VLSI Standards are NIST-traceable products, intended for calibration of both contact and non-contact sheet resistance measurement tools used in the LCD, flat panel and touch-screen markets.
-
Product
3D inversion geophysical software for Resistivity and Induced Polarization Data
RES3DINV
-
This program is designed to invert data collected with a rectangular grid of electrodes. The arrays supported include the pole-pole, pole-dipole, inline dipole-dipole, equatorial dipole-dipole and Wenner-Schlumberger. The RES3DINV program uses the smoothness-constrained least-squares inversion technique to produce a 3D model of the subsurface from the apparent resistivity data alone.
-
Product
High Resistance Meters
-
Measurements International Ltd.
Direct or Substitution Measurements, Automatic and Manual Operation, No Temperature Coefficient, Multiple Modes of Operation.
-
Product
Concrete Surface Resistivity
Surf
-
Giatec Surf™ is a laboratory test device for rapid, easy and accurate measurement of the surface electrical resistivity of concrete based on the four-probe (Wenner-Array) technique. The Surf™ patented technology automatically measures resistivity around the concrete specimen using four channels of 4-probe array (located at 90° from each other). The PC software generates the required reports according to the standard specifications.
-
Product
Decade Box, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270
-
Pocket sized resistance decade box ideal for service, prototype and experimental use.*Seven decades of resistance*28 individual slide switches*Terminals with multi way binding posts*Rugged components with ABS plastic housing case*12-month limited warranty *view Terms & Conditions for details
-
Product
PXI 10 Banks 0f 8 Channel 1 Pole MUX
40-615-021-10/8/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
Load Cell Software And Electronics
-
Custom electronics and load cell software are viable low-cost solutions for OEM applications. With custom load cell software our customers can have exactly what is needed for the application and leave out the sometimes confusing extras that most off-the-shelf products have. We also offer private labels, overlays, and splash screens that will show your company's information on the display.
-
Product
Thru Hole Donut Load Cell
-
Futek Advanced Sensor Technology, Inc.
The Thru Hole Donut Load Cell Series offers 5 models built for Off-Center Loading, Press, or Inline compression applications. These models have a very robust construction available in 17-4 Stainless Steel, with an I.D. range of 1/8" to 1 1/4".
-
Product
6/8/12 Volt 0-1000 Amp Heavy-Duty Variable Carbon Pile Load Tester
7136R
-
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Built in LCD Digital Voltmeter and LCD Digital Amp Meter• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• RoHS and CE Compliant• Made in USA of US and Global Components
-
Product
Insulation Resistance Meter
AMIC-15k1
-
The partial discharge indicator PDI. Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD. Allows to test the electrical durability of the tested object - indication of breaking voltage. The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
Product
Resistance Meter
RM3542A
-
High-speed resistance meter ideal for automated lines; compatible with super-small electronic components• Testing source: DC• Fastest measurement time: 0.9 ms• Minimum integration time: 0.1 ms• Finest resolution: 0.1 μΩ
-
Product
load cell
EST-40
-
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
Product
S Beam Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK S Beam Load Cells (Tension/Compression) offer a compact design for a variety of applications. Available in standard and metric, the S Beam Load Cell series provides accuracy, compact design features, overload protection (select models), and a wide capacity range to choose from. S Beam Load Cells are also commonly known as Z Beam Load Cells or S Type Load Cells.
-
Product
Resistance Meter
MS8-2L
-
M-module MC8-2L is a mezzanine module designed to measure resistance using a two-wire measurement scheme in eight channels (eight-channel digitizer). М-module МС8-2Л is installed on the mezzanine carrier - NM module and is connected to it via a local information highway. Up to four m-modules of various types can be installed on the HM module. The NM module, together with the m-modules installed on it, forms a VXI module of size C-1 and is used to create information measuring VXI systems.
-
Product
Transformer Winding Resistance Tester
KRI 9310
-
KRI 9310 adopt Kelvin four-wire testing method, which effectively eliminates the influence of the resistance of the test line on the test results. It can be able to increases the current to 10A by which can test extremely low resistance to 0.01 Ω(such as amorphous alloy, Copper-nickel, nickel-chromium-iron, iron-chromium-aluminum etc). For the tested objects with high resistance value (CT/PT), the instrument can extend the range to 20 kΩ，so the wide resistance test range enables KRI9310 can cover 80% of the power transformer products on the market and switchgear bus-bar cable etc. The power of the tester use the built-in rechargeable lithium battery that can test hundreds of transformers by one time charging.
-
-
Product
AC Load Banks
30 kW Series
-
Mosebach Manufacturing Company
Mosebach’s 30 kW series load banks offers a continuous load at either 480 or 208 volts in a very compact, lightweight, portable design with a 1kW resolution.
-
Product
Medium-power DC Electronic Load (900W~6000W)
FT6400A Series
-
Shenzhen FaithTech Technology Co., Ltd.
The FT6400A series has modular design, with strong adaptability, high reliability and high maintainability. Mainly used in power electronics testing fields such as power batteries, medium and high power DC power supplies, DC generators, etc. The FT6400A electronic load not only provides OCP, OVP, OPP, OTP, RVP but also provides Von and Voff functions and programmable protection functions for the device under test. These features can greatly improve the reliability of the product, and it is a reliable product for engineering test and automatic test system integration.
-
Product
Hardness & Scratch Resistance
-
Hardness can be defined as a material’s resistance to permanent deformation. In the coatings industry, hardness measurement can be used to determine the resistance of the coating to scratching from general wear and tear and also if a coating is fully cured.
-
Product
Low Profile Compressive Load Cell
CCLP-1.0
-
Low Profile Compressive Load Cell – 0.5t to 20t
-
Product
Dry Dielectric RF Coaxial Loads
4000 Series
-
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
Product
48V / 300 Amp Load
EL18-48M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
Ground Resistance Testers
-
Whether you are doing a simplified 2-Point, a more complete 3- or 4-Point Fall-of-Potential test, a soil resistivity test or a touch potential test, AEMC has the right instrument for you. Our revolutionary clamp-on ground resistance tester will save you both time and money. Whichever AEMC ground tester you choose, you can count on it to be the highest quality, the most complete package and the simplest to learn to use.
-
Product
15" XGA Industrial Monitor With Resistive Touchscreen, Direct-VGA, DVI Ports, And Wide Operating Temperature
FPM-3151G
-
15" XGA LED backlight LCD with low power consumptionRobust anodized coated aluminum front bezel and stainless steel rear coverSupports wide operating temperaturesIncrease reliability by enhanced 5-wire resistive touch sensorAnti-reflective screen with tempered glassFull enclosure ground isolation protectionSupports VGA/DVI input, dual touch interfaces and two power inputsFront lockable OSD membrane keys with user-defined brightness settingFront panel is IP65 compliantSupports panel, VESA, wall and desktop stand mounting
-
Product
17" SXGA Industrial Monitors With Resistive Touch Control, Direct HDMI, DP, And VGA Ports
FPM-217
-
17" SXGA TFT LED LCD with 50,000 backlight lifetimeDirect HDMI, DP and VGA input interfacesAnti-glare screen with tempered glassRobust system with Die-casting aluminum chassis and IP66-rated aluminum alloy front bezelLockable I/O connectorsSlim design enables easy installationSupports various mount options: panel, desktop, and VESA arm
-
Product
Hand-Held/Digital Load Tester
6030
-
• Full 125 Amp load tests 12 Volt batteries, alternators and starters on all type of vehicles• PATENTED• Made in USA of US and Global Components
-
Product
Automated Temperature Resistance Standard
-
Measurements International Ltd.
Exceptional Stability, Cost-effectiveness, Performance-based Results, 10 Ω, 25 Ω, 100 Ω, 200 Ω, 400 Ω and 1000 Ω Internal Standards, Built-in Temperature Chamber for Optimal Performance.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
