Fiber End Face
-
Product
Fiber Microscope
WL-C400S
-
The WL-C series fiber microscopes use coaxial illumination to provide users with maximum detail. It easily can detect the finest scratches and contamination, making it ideal for critically inspecting polish quality.
-
Product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
Optical Fiber 1×32 Switch
OFSW - 1 × 32
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×32 is a 1×32 prism optical switch. It can support 1 optical fibers input and 32 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
X4 Optical Fiber Fusion Splicer
-
Smart-connected APP, Splicing record management, Intelligent burglary-resisting system 1 sec. topspeed boot time, 6 sec. splicing time, 12 secs. Heating time. 3D protection cover reduce risk and unpredictability Handy, lightweight, anti-dropping solid and durable. Hi-Speed USB connection internet remote control.
-
Product
Optical Fiber Rangers
-
Fiber rangers are a form of test equipment functioning similarly to an optical time domain reflectometer (OTDR).
-
Product
Radar Front Ends
FMCW
-
The transmit signal is derived from an external VCO signal, internally multiplied, which also acts as the LO for the receive mixer. The resulting IF is conditioned for gain and filtering as required. The IF also contains an industry leading IF noise figure, especially in the frequency range below 500MHz. Custom designs available, visit our custom design page for more information.
-
Product
Protective Cover, Mini Fiber Optic, Receiver
510109501
Protective Cover
For use with modules p/n 510104243 and 510104120.
-
Product
Fiber Manufacturing
-
From preform fabrication to final quality control, our fiber test instruments are designed to provide a complete end-to-end solution for all of your testing needs. Our technology is so widely used that virtually all fibers produced globally encounter multiple PK instruments before leaving the factory.
-
Product
High Accuracy Fiber Optic Sensors
FS01
-
Compact & simple operation. New 12-bit concurrent CPU. 20-s response speed. Multiple calibration methods. Wire-Saving 0-line or 1-line connection
-
Product
Yamasaki Optical Fiber Identifier
TF916
-
The Yamasaki TF916 Optical Fiber Identifier is an essential part of any professional fiber optic toolkit. By inserting fiber into the Yamasaki TF916 Optical Fiber Identifier head, the Yamasaki TF916 Optical Fiber Identifier can be used to identify traffic, traffic direction, frequency and optical power within any singlemode optical fiber. The sleek black outer housing is comprised of an anodized aluminum to make it lightweight and tough. Also included with the Yamasaki TF916 Optical Fiber Identifier are four adaptor heads that are specifically designed to suit various optical fiber types with minimal bend loss. The easy to read ultra-bright LED display and audible tone make operation easier and can save you valuable time in the field.
-
Product
Raman Fiber Probes
-
For ultimate flexibility, fiber-coupled Raman probes offer a compact design and a rugged, robust construction for a wide range of applications. With an optional integrated camera, the user can locate a precise region of interest prior to analysis. Also available are immersion probes and non-contact optics.
-
Product
3'Harness, 50-Pin Male D-sub Connector on one end, loose wired (numbered) other end
GT97107
-
3' harness, 50-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Dual Fiber Transceivers
-
The benefits and overall savings on a single strand (simplex) versusdual strand (duplex) fiber implementation can be considerable.Considerations include not only the cost of fiber optic cabling itself,but also the labor and material involved in terminating the endpoints,simplex versus duplex patch cords, cross-connect rack space, reducedpoints of failure, and other direct and indirect costs. This technologycan also defer the need to install new fiber to support unexpectedgrowth requirements.
-
Product
Rod End Load Cell
-
Futek Advanced Sensor Technology, Inc.
FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity
-
Product
Fiber Optic Modem
VCH-608
-
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
Product
Tool, Extraction, Mini Fiber Optic, Receiver And ITA
910112125
Extraction Tool
Tool, Extraction, Mini Fiber Optic, Receiver and ITA
-
Product
Optical Fiber 13×1 Switch
OFSW - 13 × 1
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 13×1 is a 13×1 prism optical switch. It can support 13 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
End of Line Noise Test System
-
End of Line Noise Test Systems from VIacoustics are designed to support end of line product noise testing on factory floors and quality assurance environments. Using the Limit Analysis features of the Nelson Acoustic Trident software, users can set noise emission maximum, minimum or control range criteria based on Awtd and/or 1/N octave band criteria. Criteria can be customized for most any type of product based on the noise emissions of known good and bad units. The large front panel Pass/Fail indicator allows operators to quickly determine if units meet the criteria. Data on units that fail can be exported for further analysis.
-
Product
Erbium Doped Fiber Amplifier
S-102
-
The EDFA slot module of FOTS system with built-in power booster EDFA module offers a special function that is able to change the optical signal amplification feature variously, which is followed by user’s driving embedded pump LD freely. The output power of eash pump LD can be controlled separately by the program that is set up by user. When an optimum optical signal amplification particularity is needed, it is made up so that it can be materialized by choosing the Default mode provided along with User mode. More stable application of EDFA is possible through the monitoring of the factors such as in/out signal power, gain, alarm status and pump LD enabled by the application of FPGA processor which makes high speed driving possible. It is also set up that user’s present-time monitoring and control through LCD monitor of system main frame or GUI display for remote control can be possible. Through optimization of amplifier gain, noise figure, and saturated output power, this EDFA module will expand test capabilities in systems, components or sub-assembly manufacturing.
-
Product
Fiber Sensors
-
Easy to install.Numeric displays, interactive prompts.Applications focus on many industries,such as semiconductor assembly, handling technology and packing.Depends on the mounting direction, the digital display of BR1 can be inverted.Response time selectable:(20050010005000)s.
-
Product
Fiber Cleaver
CARY-C500
-
The CARY-F600H optical fiber cleaver easy to use, convenient, rotating blade, no positionlimited, high-precision cutting. Optical fiber cleaver light weight. Cleave angle: < 1 degree .Replaceable blade cleave blade with 16 cleave spots.
-
Product
Fiber Optic Accelerometer
MR660
-
The MR660 Series Accelerometer provides an innovative solution to measure vibration and movement in high voltage or ATEX environments. The MR660 Accelerometer system employs a highly sensitive MEMS membrane to provide a robust system capable of producing an output signal of 100mV/g pk-pk.
-
Product
Rugged Fiber Connectors
-
TE's ruggedized fiber optics brings the benefits of optical technology to challenging environments providing more bandwidth, more distance, and more performance. Our offering includes Ethernet and other fast communications protocols with the capacity to handle next-generation 40G and 100G when you are ready without the severe distance limitations of copper cables. Optical cables also offer significant size and weight savings to help meet SWaP goals.
-
Product
High-efficiency Fiber Stretcher
PZ2
-
The PZ2 provides the most extensive stretch of our stretcher product family. It is a fiber wound piezoelectric element for use in a wide range of optical interferometric measurement and sensing system applications. Typical uses include open loop demodulation, sensor simulation, white-light scanning interferometry and large angle modulation of interferometric phase. The PZ2 is ideal for use in OCT [Optical Coherence Tomography] and OCDR [Optical Coherence Domain Reflectometry] applications requiring scattering or boundary definition measurements.
-
Product
Fiber light source
-
UV irradiation UV curing, infrared irradiation Thermal curing is possible with one unit. All-round player suitable for R & D · mass production line
-
Product
Measurement Front End of the ACQUAlab Generation
LabBGN
-
labBGN is the first of the new ACQUAlab generation of measurement front ends. It is used in conjunction with the background noise simulation systems 3PASS HAE-BGN/ HAE-car, the communication analysis system ACQUA and other HEAD acoustics components.
-
Product
Handheld Fiber Optical Power Meter
3208
-
Anfkom International Co.,Limited
3208 handheld optical power meter is a compact and an easy-to-use testing instrument for optical fiber networks, which can be used for absolute optical power measurements as well as for relative loss measurements in optical fibers. It features ingenious appearance, wide range of power measurement, high accuracy and user self-calibration function with high performance-to-price ratio.
-
Product
PXI Dual 2 Channel Fiber MUX ST
40-855-522-M
-
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Optical Fiber Identifier
TM301
-
TM301 Optical Fiber Identifier (Live Fiber Detector) is an essential instrument for the installation and maintenance of optical fiber projects. It can easily detect any spot of SM fiber cables. Through inserting a 1310 or 1550 modulated signal into the fiber, it is used to indicate the direction of the transmitting signals, find and locate the specific fiber without interrupting the normal work during the installation, cabling and maintenance.
-
Product
100GHz Single Fiber Bi-Direction Dense WDM
DWDM-1200
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDM-1204, DWDM-1208 dense DWDM DWDM, which is based on mature thin film filtering technology, It has the feature of low insertion loss, high isolation and flexible channel configuration. It can bi-direction transmit 4 channel(1204) or 8 channel(1208) on one fiber up stream/down stream.
