Shielding Effectiveness
the ability to block an electromagnetic field.
See Also: Shielding, RF Enclosures
-
Product
Signal, Patchcord, ITA, 36", TriPaddle (30 Micron), 4 Conductor Shielded 22/24AWG 120Ω
7-103889000-036
-
Signal, Patchcord, ITA, 36", TriPaddle (30 Micron), 4 Conductor Shielded 22/24AWG 120Ω
-
Product
X2 GPIB Cable,Double-Shielded,Shielded Plug/Receptacles,8 m
763061-04
-
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
Product
Hall Effect Thickness Gage
Magna-Mike 8600
-
The Magna-Mike® 8600 is a portable thickness gage that uses a simple magnetic method to make reliable and repeatable measurements on nonferrous materials. Operation of the Magna-Mike is very simple. Measurements are made when its magnetic probe is held or scanned on one side of the test material and a small target ball (or disk or wire) is placed on the opposite side or dropped inside a container.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-K
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Shielding Solutions
-
The highly transparent EMC shielding material Aaronia-Shield® and the high-tech EMC shielding fleece Aaronia X-Dream®, for example, offer very high EMC protection and are especially well equipped for all future high-frequency radiation sources in the high GHz range, which you can easily verify with our EMC Handheld Spectrum Analyzer. For magnetic field shielding, our MagnoShield® series offers unparalleled protection against alternating magnetic fields, such as cables, power distributors, high-voltage lines or transformers and generators.
-
Product
PXI 50 Shielded SPST Reed Relays
40-142-021
-
The 40-140A/141/142/143 range of high density switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-ST
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
PCI 32xSPST Shielded Reed Relay Card
50-125-021
-
The 50-110/115 range of PCI shielded switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
Hall Effect Measurement system
HMS-5000
-
Constant current source + Van der Pauw method terminal conversion system
-
Product
RF Shielded Test Enclosure, Large interior for multiple device
JRE 1812
-
Developed expressly for high volume testing of larger RF devices, the 1812 is roomy enough for holding both TX and RX devices for actual on-air tests. Top loading keeps door swing out of the way on congested benchtops. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness.
-
Product
Measuring Device for Testing the Effectiveness of Residual Current Protective Devices (RCD) According to DIN EN 61557-6 (VDE 0413-6)
-
PeakTech Prüf- und Messtechnik GmbH
A residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE).
-
Product
Hall Effect Sensor
-
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
Product
Hall Effect Sensor Elements/ICs
-
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
Product
Shield Room
-
Our world depends on digital information & operation. An increasingly electromagnetically polluted environment, solar storms or weaponizing (H)EMP may put your operation at risk, leading to destroyed electronics, data breaches or even espionage. Owning an in-house high-performance RF-shielded enclosure is the best way to secure your critical operation and information. We understand your safety concerns. That’s why we strive for worry-free solutions with the highest level of security, precisely tailored to your needs.
-
Product
SHB12X-B12X, 73-Pin, Male InfiniBand to 73-Pin, Male InfiniBand, 100 Ohm, Shielded LVDS Cable, 1m
192344-01
-
The SHB12X-B12X LVDS Cable 1m connects the 12X InfiniBand connector on PXIe-656x LVDS instruments or some NI 658x LVDS Adapter Modules for FlexRIO with other NI accessories such as the SMA-2164 to break out cable signals for direct access. It is a shielded, 100 ohm cable that is offered in various lengths.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.Each order comes with one board and a set of four female, long extension, headers that can be soldered to the board. If stacking two of these modules on top of each other, please order both a Ch 0-3 and a Ch 4-7 board, as well as an additional set of headers for stacking. We're working on sourcing even longer headers, but the ones currently available are not long enough to stack as-is (they need to be double-stacked).The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or MegaNote: we also offer a universal version of this board in a smaller for factor, the SEN-30003-T.FeaturesType-specific, miniature-sized vertical thermocouple connectors (vertical flat blades, see pics)Measures four (4) thermocouple channels, full extended range.Boards are stackable. Up to 8 thermocouple channels may be connected to an Arduino.14-bit SPI interfacePlugs directly into an Arduino Uno or Mega form factor with built-in voltage level translation on-board.Standard Arduino female headers required for easy configuration, one set included with order (1-6x1, 2-8x1, 1-10x1 0.1" female stackable headers), not soldered on.Detects shorts to GND or VccDetects open thermocoupleOther versions available (K, J, and T stocked). Contact Customer Service to place a custom order.Mounting holes for 4-40 sized screwsConnections are spaced for 0.1" pin headerDesigned, manufactured, tested and shipped from the USA The MAX31855T supports a measured temperature range of -270C-400C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
RF Shielded Box
LTL B12001
-
LTL B12001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL B12001 RF shielded test enclosure can comfortably houses the intermediate and large devices on test such as Laptops, larger test Fixtures and other large RF devices.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
RF Shielded Test Enclosure, Largest Rack Mountable Enclosure
JRE 1724
-
Originally designed for testing wide screen laptops, the rack-mountable JRE1724 is ideal for large wireless devices such as; Mesh Network AP's, Cellular/LTE/4G Base Stations, and other large RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble free operation over its lifespan. Internal struts keep the lid open for easy internal access when connecting the device under test.
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Hall Effect Measurement System
RH 2010
-
The RH 2010 Hall Effect Measurement System has been designed for high flexibility and ease of use as a standard system for quick routine control measurements as well as for sophisticated temperature dependent Hall measurements for material research.
-
Product
Coax, Patchcord, ITA, 36", Mini Coax, RG316DS Tan (Double Shield), Single Ended
7-351117000-036
-
Coax, Patchcord, ITA, 36", Mini Coax, RG316DS Tan (Double Shield), Single Ended.
-
Product
RF Shielded Test Enclosure
JRE 0709-P
-
Containing all the capability of the larger JRE enclosures, the compact JRE 0709-P is ideal for small wireless devices such as; cell phones, pagers, WiFi dongles and other small RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth troublefree operation over its lifespan.
-
Product
Split Core Hall Effect DC Current Sensor
CYHCT-C2TC
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a split core and a high galvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
Coax, Patchcord, Receiver, 72", Micro Coax, RG316 Double Shield Tan, SMB Plug
7-368117652-072
-
Coax, Patchcord, Receiver, 72", Micro Coax, RG316 Double Shield Tan, SMB Plug.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
Product
SCB-19 Noise Rejecting, Shielded Aux I/O Connector Block For FlexRIO
782444-01
-
Screw Terminal, 19-Pin HDMI, Noise Rejecting, Shielded AUX I/O Connector Block.
-
Product
Arduino CAN Shield
IFB-10003-AWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended
7-121974000-036
-
Signal, Patchcord, ITA, 36", QuadraPaddle, 24AWG Single Conductor Shielded, Single Ended.
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
