Light Fixture
-
product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Component Test Fixture For N1413 With B2980 Series
N1428A
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
product
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA
910121178
Tool, Soldering Fixture, Micro Coaxial, Receiver and ITA.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
-
product
Bottom Electrode SMD Test Fixture
16197A
The 16197A is designed for impedance evaluations of bottom electrode SMDs. It achieves stable frequency characteristics up to 3 GHz and provides highly repeatable measurements. The Keysight 16197A supports various SMD sizes, as small as 1005 (mm)/0402 (inch) and as large as 3225 (mm)/1210 (inch). Accommodation of the 0603 (mm)/0201 (inch) size is available with option 001.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196B
The 16196B surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results, reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement. Now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Dielectric Test Fixture
16451B
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
product
SMD Array Type LCR Test Fixture
16034H
The 16034H is designed for impedance evaluations of array-type SMD.The minimum SMD size that this fixture is adapted to evaluate is 1.6(L)x0.8(W)[mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact each of the elements of the array-type component.
-
product
Test Fixture, Axial And Radial
16047A
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
product
Test Fixture
N1295A
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
product
SMD Test Fixture
16034G
Perform impedance evaluation on a minimum SMD size of 0.6(L) x 0.3(W) [mm]
-
product
Bottom Electrode SMD Test Fixture
16198A
Designed for impedance evaluations of bottom electrode SMDs and supports 201 (mm) and 402 (mm) sizes
-
product
Cameras and Lights
MacArtney LUXUS cameras and lights are designed to combine operational and service flexibility, excellent performance and reliability.
-
product
Lighting ICs
Based on its 30-year experience in power conversion and high-voltage technology, ST offers a wide portfolio of solutions for electronic ballasts, ranging from high-voltage ballast controllers for analog solutions (with or without embedded PFC), to complete power management units with integrated drivers and voltage regulator for digital platforms.
-
product
Light Source
UVF-502S
In combination use with the uniform exposure unit, selection of uniform irradiation area in the range of 80mm200mm is possible.
-
product
Automatic Fixture Removal
S95007B
Many devices do not have coaxial connectors and so they are put in fixtures in order to measure them in a coaxial environment. You must accurately remove the effects of the fixture to get a good measurement of the device under test (DUT). This option adds a powerful application wizard to guide you through characterizing a fixture and removing it from the measurement. The S95007B software is compatible with M980xA PXI Vector Network Analyzers.
-
product
Fixture Design
TestEdge offers quick, cost effective test fixture design services for low-speed, full-speed, and high-speed devices. Based on our experience in developing high performance test fixtures for a wide variety of devices, test sockets, and tester platforms, we provide a premium quality test and engineering validation environment for everything from high power (40W) to high pin count to high speed ECL to high speed SerDes (3.25Gb) devices.
-
product
Functional Test Fixtures
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
product
Structured Light
Structured light systems from ams enable 3D imaging applications to achieve extremely high accuracy. Accurate structured light technology is behind the user face recognition being implemented in smartphones. Structured light products and design expertise from ams help customers get to market quickly and scale up production rapidly.
-
product
Light Meters
Meter reads from 0 to 1,999 foot-candles (resolution 0.1 to 1). Bright 1/2-inch-high digits make it an easy to read pocket light meter. The simplicity of the two-button operation eliminates the need to refer to directions. Functions are on/off, and range. The meter can be zeroed with the simple turn of an adjustment screw
-
product
Wave Profiler Fixture
KIC® Wave Surfer™
The KIC Wave Surfer is a self-contained system that provides critical data on wave solder machine set up and performance. Used in conjunction with your SlimKIC 2000 and the KIC 2000 software, you can ensure your wave solder machine is set up and performing properly.
-
product
Light Meter
Lumu Light Meter incorporate two state of the art sensors. True color sensor, based on the color standard CIE 1931/DIN 5033, and fast silicon photodiode capturing light at astonishing 750 000 measurements/second. Each Lumu Light Meter is calibrated before leaving the manufacturing line and comes with calibration certificate.
-
product
Mechanical Test Fixtures
MMI series man-machine interface
Designed to meet the needs of the most discerning customers and the latest market demands, our MMI series guarantees a natural posture for both the operator and the sitting position when performing the test on the adapter. The newly developed lever mechanism, which has been registered as a utility model, is specially adapted to the hand movement of its employee and ensures a heart-loving strain on the operator.
-
product
Test Fixture Adapters for In-Circuit Test Fixtures
Circuit Check test fixture adapters are utilized when the target ICT tester is not available or has been replaced with a newer technology tester. The tester adapter will often allow existing test fixtures from one test manufacturer to be utilized on another manufacturer test platform, eliminating the need for replacement fixtures. Contact Circuit Check to discuss your tester and fixture combinations for the best choice of a cost effective solution.
-
-
