-
Product
3U 4HP PMC Adapter for cPCI
cPCIBPMC3U32
-
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
-
Product
10GBASE-T Ethernet PCI Express 2.1 x4 Single Port Adapter, AQC107
10 GigE Network Interface Cards
-
10GBASE-T Ethernet PCI Express 2.1 x4 Single Port Adapter, AQC107
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 40 to 60 GHz
U281B
-
The Keysight U281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
ACC-188 Synchronous Serial Radio Adapter
-
The ACC-188 synchronous serial radio adapter is interoperable among various tactical radio brands and models used by the defense community. The ACC-188 works with any radio that has a synchronous serial communication port using MIL-STD-188-184 and enables the tactical radios to send data such as GPS maps, images, coordinates, and IM-type communications.
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
Network Interface Controller
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
Manual Test Adapter With Rigid Needles
-
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
Product
3U CPCI To PCI 4 Slot Adapter
-
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
-
Product
Self Test Application Adapter and Software
OTP2-Modul-Nr210
-
In order for the system to carry out a self-test, it requires a suitable adapter and software that is tailored to the test system. A self-test is often very helpful and recommended if a system has not been used for a long time or also to see whether the test system is working properly with the specified parameters.
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 40 to 60 GHz
U281A
-
The Keysight U281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
RF Adapters
SMA Adapters
-
Are semi-precision coaxial RF connectors developed in the 1960s as a minimal connector interface for coaxial cable with a screw-type coupling mechanism.
-
Product
Ethernet to CAN Bus Gateway
YAV90090
Ethernet Interface
• High-performance Arm Cortex-M3 MCU with 512 Kbytes Flash, 120 MHz CPU, ART Accelerator, Ethernet P/N STM32F207IEH6• USB 2.0 connector for serial data transfer (reserved for factory use)• Connections for CAN, and power supply via 4-pole Weidmüller connector• Reboot and reset of the device to factory defaults with a reset button• Plastic casing for benchtop operation• LEDs for device status and power supply• Voltage supply from 8 to 30 V
-
-
Product
PXI 8 Slot BRIC 184x8 1-Pole Dual Analog Bus (4 sub-cards)
40-560A-121-184X8-M
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
ITA, G20x, 28 Module, 6.75" Series Adapters
410120210
ITA
ITA, G20x, 28 Module, 6.75" Series Adapters
-
Product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
-
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag information appended to each word, and also allow for filtering and multi-storage modes of data words. The transmit channels operate via a transmit ‘instruction stack’ which allows scheduling of data transmissions and reduces the need for host computer intervention. The EXC-9810 supports up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.The EXC-9810/Ax adapter is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application (only versions 8.1 or higher). Please see multi protocol 8000 modules for additional information on protocols that can be added to this card.
-
Product
Small IC Adapter for ZD Differential Probe Qty 2
PACC-ZD006
-
Small IC adapter for ZD differential probeQty 2
-
-
Product
RF Adapters
SMPM Adapters
-
a type of blind-mate, push-on connector that is similar to SMP connectors.
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
Product
PXI 8 Slot BRIC Module, 1 Resource Distributor, 6 Bus Matrix Inputs
40-569B-116
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-116 is a 8 slot module fitted with 6 Bus Matrix Inputs cards and 1 Resource Distributor card.
-
Product
PCI Adapter for cPCI
PCI2cPCI
-
PCI2cPCI is an adapter familiy used to mount a cPCI device into a PCI connector. PCI2cPCI-32, PCI2cPCI-32-IO, and PCI2cPCI-64 are passive devices with impedance controlled traces interconnecting the Gold Fingers of the PCI edge connector to the press fit cPCI connector. All PCI signals are routed through including power, ground, PCI bus, secondary control signals.
-
Product
XMC-to-PCI Express (PCIe) Adapter
9956
-
The Technobox XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC or VITA 20 conduction-cooled XMC in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board and is not the low-profile version.
-
Product
Wireless Airflow Temperature Humidity Adapter
DTHA2
-
UEi Test & Measurement Instruments
Airflow Temperature Humidity Adapter with Free App
-
Product
Right Angle Waveguide to Coax Adapters
-
Fairview Microwave right angle waveguide to coax adapters include millimeter wave frequency ranges with models in the K-band (18 to 26.5 GHz) up to the V-band (50 to 65 GHz). These right angle waveguide to coax adapters offer excellent VSWR as low as 1.29:1, while also providing insertion loss performance as low as 0.3 dB. Waveguide sizes available for these new 90 degree coaxial adapter models include WR-42, WR-28, WR-22, WR-19 and WR-15. These coax to waveguide adapters in a right angle design are ideal for numerous applications requiring a transition from coaxial cable to waveguide or vice versa, including SATCOM, wireless communications, industrial, test and measurement and defense systems. Fairview’s new waveguide to coax adapter products feature a right-angle configuration, those with 2.92mm connectors use a UG-style square waveguide flange, 2.4mm and 1.85mm connector versions use a UG-style circular waveguide flange. Both male and female connector options are available in each right angle waveguide to coax adapter frequency band.
-
Product
2.54mm PCB Adapter for ZS4000 (Qty.10)
PK-ZS-024
PCB Adapter
2.54mm PCB Adapter - ZS4000 (Qty.10)
-
Product
PCIe Adapter for PMC
PCIeBPMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With PCIeBPMCX2´s two positions a PrPMC can be matched with another PMC to make a high bandwidth processing node. The PrPMC can communicate with the host for set-up, and then use the local bus to control and transfer data with the special purpose IO card. For example the PMC-BiSerial-VI-HW1 provides 32 ports of manchester encoded data.
-
Product
I2C Bus Monitor
Model JI-210
-
The JI-210 is a PC hosted I2C bus monitor used to non-invasivelymonitor and analyze a variety of I2C networks. The desktop unitcaptures and stores up to 32KBs of bus activity including data andaddress values, stop/start, read/write, ACK/NACK, and frame errorevents. Data is displayed as both I2C messages and TimingWaveforms. A Windows software application manages capturedI2C messages, trigger setup, and recording settings.
-
Product
EBIRST 200-pin LFH To 160-pin DIN Adapter
93-002-410
Test Adapter
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
4U CompactPCI® Enclosure with cPCI Power Supply (non-CT Bus)
MIC-3042
Enclosure
The MIC-3042 is a 4U enclosure designed for standard cPCI power supplies. It is equipped with a cPCI 500 W redundant 2 1 power supply with hot-swap support. The system has 8 slots for CompactPCI boards and 6 slots for IEEE 1101.11 rear I/O transition boards. The MIC-3042 comes with a built-in high quality backplane that supports 64-bit / 66 MHz PCI cards.
